9" X 48" EVS MILLING MACHINE w/COOLANT SYSTEM & POWER FEED MODEL SB1027 OWNER'S MANUAL Hundreds of Thousands of Lathes Sold With a Tradition of Q uality Since 1906! Copyright © April, 2010 For Machines Mfg.
Scope of Manual This manual helps the reader understand the machine, how to prepare it for operation, how to control it during operation, and how to keep it in good working condition. We assume the reader has a basic understanding of how to operate this type of machine, but that the reader is not familiar with the controls and adjustments of this specific model. As with all machinery of this nature, learning the nuances of operation is a process that happens through training and experience.
Table of Contents INTRODUCTION About This Machine.............................................. 3 Foreword. ............................................................ 3 Capabilities.......................................................... 3 Features. ............................................................. 3 Full View Identification........................................ 4 Drive System, Headstock, & Control Panel Identification............................. 5 Machine Specifications..................
Adjusting Leadscrew Backlash.......................... 51 Longitudinal Leadscrew Backlash. ..................... 52 Cross Leadscrew Backlash.................................. 52 Belt Tensioning................................................... 53 TROUBLESHOOTING.................................................. 54 ELECTRICAL Electrical Safety Instructions............................ 56 Upper Electrical Panel....................................... 57 Lower Electrical Panel...................................
For Machines Mfg. Since 8/09 INTRODUCTION Model SB1027 About This Machine Foreword Capabilities "Most boys should learn a trade in order that they may become skilled workmen. The trained workman is always in demand...When a boy has learned a trade, becomes a skilled mechanic, he has excellent equipment with which to begin life's battle, but he need not stop there.
INTRODUCTION Model SB1027 For Machines Mfg. Since 8/09 Full View Identification Drive System & Headstock (See Page 5 for Identification) Control Panel (See Page 5 for Identification) Lifting Eye Bolt Coolant Nozzle & Valve Electrical Cabinet Work Table Power Feed Limit Switch X-Axis Ball Handle X-Axis Power Feed Y-Axis Ball Handle Coolant Return Hose Knee Z-Axis Crank One-Shot Oiler Splash Pan Figure 1. SB1027 full view identification.
INTRODUCTION For Machines Mfg.
INTRODUCTION Model SB1027 For Machines Mfg. Since 8/09 Machine Specifications P.O. Box 2027, Bellingham, WA 98227 U.S.A. Machine Specifications PHONE: (360) 647- 0801 Ext. 223 • FAX: (360) 676 -1075 www.southbendlathe.com Model SB1027 9" x 48" EVS Milling Machine w/Coolant System & Power Feed Product Dimensions: Weight ........................................................................................................................................................................2156 lbs.
For Machines Mfg. Since 8/09 INTRODUCTION Model SB1027 Motors (continued): Coolant Pump Type .............................................................................................................................................. TE Induction Class F Horsepower............................................................................................................................................................. 1⁄8 HP Voltage .....................................................................
Model SB1027 INTRODUCTION For Machines Mfg. Since 8/09 Other Specifications Machine No-Load Sound Level @ 5000 RPM ................................................................................................................ 54 dB Country of Origin ......................................................................................................................................................... Taiwan Warranty .......................................................................................
For Machines Mfg. Since 8/09 SAFETY Model SB1027 Understanding Risks of Machinery Operating all machinery and machining equipment can be dangerous or relatively safe depending on how it is installed and maintained, and the operator's experience, common sense, risk awareness, working conditions, and use of personal protective equipment (safety glasses, respirators, etc.). The owner of this machinery or equipment is ultimately responsible for its safe use.
Model SB1027 SAFETY For Machines Mfg. Since 8/09 5. Entanglement: Loose clothing, gloves, neckties, jewelry or long hair may get caught in moving parts, causing entanglement, amputation, crushing, or strangulation. Reduce this risk by removing/securing these items so they cannot contact moving parts. 11. Chuck Keys or Adjusting Tools: Tools used to adjust spindles, chucks, or any moving/ rotating parts will become dangerous projectiles if left in place when the machine is started.
For Machines Mfg. Since 8/09 SAFETY Model SB1027 Additional Milling Machine Safety 1. Understanding Controls: The mill is a complex machine that presents severe cutting or amputation hazards if used incorrectly. Make sure you understand the use and operation of all controls before you begin milling. 2. Safety Accessories: Flying chips or debris from the cutting operation can cause eye injury or blindness. Always use a chip guard in addition to your safety glasses or use a face shield when milling. 3.
Model SB1027 P R E PA R AT I O N For Machines Mfg. Since 8/09 Preparation Overview Things You'll Need The purpose of the preparation section is to help you prepare your machine for operation. The typical preparation process is as follows: During the setup process, operation, and maintenance of your machine, you'll need the following items: 1. Unpack the machine and inventory the contents of the box/crate. For Lifting 2. Clean the machine and its components. • 3.
For Machines Mfg. Since 8/09 P R E PA R AT I O N Model SB1027 Unpacking This item was carefully packaged to prevent damage during transport. If you discover any damage, please immediately call Customer Service at (360) 734-1540 for advice. You may need to file a freight claim, so save the containers and all packing materials for possible inspection by the carrier or its agent.
Model SB1027 P R E PA R AT I O N For Machines Mfg. Since 8/09 Cleaning & Protecting The unpainted surfaces are coated at the factory with a heavy-duty rust preventative that prevents corrosion during shipment and storage. The benefit of this rust preventative is that it works very well. The downside is that it can be time-consuming to thoroughly remove. Be patient and do a careful job when cleaning and removing the rust preventative.
P R E PA R AT I O N For Machines Mfg. Since 8/09 Location Model SB1027 Weight Load Physical Environment The physical environment where your machine is operated is important for safe operation and longevity of parts. For best results, operate this machine in a dry environment that is free from excessive moisture, hazardous or flammable chemicals, airborne abrasives, or extreme conditions.
P R E PA R AT I O N Model SB1027 Lifting & Moving This machine and its parts are heavy! Serious personal injury may occur if safe moving methods are not used. To reduce the risk of a lifting or dropping injury, ask others for help and use power equipment. 2. Lifting Web Straps Turret Lock Bolts Important: Before lifting the mill, make sure the four turret lock bolts (two on either side of the ram) are torqued to 47 ft/lbs. 1.
For Machines Mfg. Since 8/09 P R E PA R AT I O N Leveling & Mounting Model SB1027 Bolting to Concrete Floors Although not required, we recommend that you level your machine and mount it to the floor. Because this is an optional step and floor materials may vary, mounting hardware is not included. Generally, you can either bolt your machine to the floor or mount it on machine mounts. Anchor Bolt We strongly recommend securing your machine to the floor if it is hardwired to the power source.
Model SB1027 P R E PA R AT I O N For Machines Mfg. Since 8/09 Assembly 5. Remove the hex nut from the Y-axis leadscrew. Ball Handles 6. Align the keyway of the ball handle with leadscrew key, slide the Y-axis ball handle (see Figure 8) onto the leadscrew, then secure it in place with the removed hex nut. 7. Thread the handles into the small end of the ball handles and tighten them with a wrench.
For Machines Mfg. Since 8/09 P R E PA R AT I O N Way Covers 1. Remove the five button-head cap screws shown in Figure 10 from the front of the saddle and knee, position the pleated way cover in place, then secure it with the removed cap screws. Model SB1027 Splash Pan & Coolant Return Hoses 1. Remove the three cap screws shown in Figure 12 from the base rim, slide the splash pan into position, then secure it with the removed cap screws.
Model SB1027 5. 6. P R E PA R AT I O N Loosen the hose clamp screws above the coolant return screens in the base (see Figure 13 on the previous page), insert the hoses so that they will drain into the screens, then re-tighten the clamp screws to secure them in place. Fine Downfeed Handwheel Electrocution or fire may occur if machine is ungrounded, incorrectly connected to power, or connected to an undersized circuit. Use a qualified electrician to ensure a safe power connection.
For Machines Mfg. Since 8/09 P R E PA R AT I O N Model SB1027 Test Run Pulling the power plug from the receptacle while the mill is running could damage the inverter inside the electrical box or other electrical parts. Always use the emergency STOP button or the circuit breaker to turn the mill OFF before pulling the plug. After all preparation steps have been completed, the machine and its safety features must be tested to ensure correct operation.
Model SB1027 P R E PA R AT I O N 5. Set the spindle speed to the low range (refer to the Setting Spindle Speed Range section beginning on Page 34 for detailed instructions). 6. Move the downfeed selector to the manual (forward) position so that the spindle does not feed into the table during this test (refer to the Downfeed Operations section on Page 35 for detailed instructions). 7.
For Machines Mfg. Since 8/09 P R E PA R AT I O N 14. Turn the spindle direction switch to the stop (middle) position to prevent the spindle from starting when you next use the ON button. 15. Make sure the emergency STOP button has been reset, press the ON button, then start spindle rotation. 16. Push the spindle brake lever—the spindle motor should turn OFF and the spindle should come to a stop from the pressure of the brake. Model SB1027 3. Loosen the table locks on the front of the table. 4.
Model SB1027 P R E PA R AT I O N For Machines Mfg. Since 8/09 Spindle Break-In Complete the spindle bearing break-in procedure to avoid rapid deterioration of spindle components when the mill is placed into operation. The high-quality bearings and gears used in the mill are manufactured to very close tolerances. However, this does not guarantee perfect dimensional mating of the bearing components or exact meshing of gear teeth.
For Machines Mfg. Since 8/09 O P E R AT I O N Model SB1027 Operation Overview The purpose of this overview is to give an example of a typical milling operation. Read through the steps below to better understand the controls and functions described later in this manual, so that you will know how they are used to successfully operate the mill. Loose hair, clothing, or jewelry could get caught in machinery and cause serious personal injury.
O P E R AT I O N Model SB1027 Control Panel Use Figures 17–18 and the following descriptions to understand the functions of the mill main power switch and the control panel. Main Power Switch: When turned ON, enables power to flow to the control panel. For Machines Mfg. Since 8/09 Spindle Speed Display Spindle Speed Dial Spindle Direction Switch Emergency STOP Button Main Power Switch Coolant Switch ON Button Figure 18. Control panel. Figure 17.
O P E R AT I O N For Machines Mfg. Since 8/09 Table Movement The mill table moves in three directions, as illustrated in Figure 19: • • • X-axis (longitudinal) Y-axis (cross) Z-axis (vertical) Model SB1027 Table Locks Refer to Figure 20 for the locations of the locks used to secure the table in place. X-Axis Locks Y-Axis Lock These movements are controlled by table ball handles and the Z-axis crank. Additionally, the table can be moved along the X-axis with the power feed.
O P E R AT I O N Model SB1027 X-Axis Power Feed The mill is equipped with a power feed unit for X-axis table movement. Refer to the illustration in Figure 22 and the descriptions below to understand the functions of the various components of the power feed system. D F G Limit Switch: Stops table movement when either of the switch side plungers are pressed by the limit stops. B. Limit Stop: Restricts table movement when positioned along the front of the table. C.
For Machines Mfg. Since 8/09 O P E R AT I O N Model SB1027 Head Movement The mill head tilts 45° back and forth, and rotates 90° left and right, as shown in Figures 23–24. 45° Always lock the head firmly in place after tilting or rotating it. Unexpected movement of the head during operations could cause damage to the cutter or workpiece. Tool Needed Qty Wrench 19mm........................................................ 1 Tilting Head 1. DISCONNECT MILL FROM POWER! 2.
O P E R AT I O N Model SB1027 Rotating Head For Machines Mfg. Since 8/09 Tramming Spindle 1. DISCONNECT MILL FROM POWER! 2. Loosen the four rotation lock bolts on the face of the head shown in Figure 26. ! After positioning the head at an angle and when your operation requires that the spindle axis be precisely perpendicular to the table, you must tram or align the spindle with the table to ensure the spindle is exactly 90° to the table.
For Machines Mfg. Since 8/09 O P E R AT I O N Tools Needed Qty Dial Test Indicator (with at least 0.0005" resolution)................... 1 Indicator Holder (mounted on the quill/spindle)....................... 1 Precision Parallel Block (at least 9" in length)...................................... 1 4.
Model SB1027 O P E R AT I O N Note: Generally, the goal in the next steps is to get the difference of the indicator readings between the end of the parallel bar down to 0.0005". However, the acceptable variance will depend on the requirements for your operation. 6. 7. Rotate the spindle by hand so that the indicator point rests on one end of the parallel block, as illustrated in Figure 29, then zero the dial.
For Machines Mfg. Since 8/09 O P E R AT I O N Model SB1027 Ram Movement The ram travels back and forth 13" and rotates 360° in either direction around the turret. Tool Needed Qty Wrench 19mm........................................................ 1 Moving Ram Back and Forth 1. DISCONNECT MILL FROM POWER! 2. Loosen the two lock levers shown in Figure 31 on the right side of the ram. ! Always lock the head firmly in place after tilting or rotating it.
O P E R AT I O N Model SB1027 For Machines Mfg. Since 8/09 Setting Spindle Speed Using the correct spindle speed is important for safe and satisfactory results, as well as maximizing tool life. To set the spindle speed for your operation, you will need to: (1) Determine the best spindle speed for the cutting task, and (2) configure the mill controls to produce the required spindle speed.
O P E R AT I O N For Machines Mfg. Since 8/09 3. Press the spindle speed range lever shown in Figure 34 toward the head to release the detent pin from the detent plate, move selector so that the pin is over the other detent, then release the selector. — When the lever is pointing to the rear and the front detent is engaged, the low speed range is selected. Conversely, when the lever is pointing toward the front and the rear detent is engaged, the high speed range is selected.
Model SB1027 O P E R AT I O N 4. Manual (Disengaged) Position For Machines Mfg. Since 8/09 Make sure the pin of the coarse downfeed handle hub is engaged with one of the detents on the downfeed sleeve (see Figure 38). Handle Hub Auto-Downfeed (Engaged) Position Detents & Pin Figure 38. Coarse downfeed handle hub, detents, and pin. Figure 37. Downfeed selector positions. -36- 5. Make sure the quill lock lever is loose so that the quill can easily move. 6.
O P E R AT I O N For Machines Mfg. Since 8/09 Fine Downfeed Controls There are a number of devices on the head that are used with the fine downfeed handwheel or the auto-downfeed system. Refer to Figure 39 and the descriptions below to become familiar with these controls. I A B G D G. Downfeed Stop & Locking Wheel: Sets the depth of spindle downfeed. The stop is threaded into position, then the locking wheel is used to secure it in place. H.
Model SB1027 O P E R AT I O N Using the Auto-Downfeed System When using the auto-downfeed system, the spindle will move in the direction you choose with the auto-downfeed direction pin. When the quill dog reaches the top or meets the downfeed stop, the downfeed clutch lever releases. Then, if the spindle was traveling upward, the movement simply stops. If the spindle was traveling downward, then the spindle moves back to the top at a rate controlled by the return spring on the left side of the head.
For Machines Mfg. Since 8/09 O P E R AT I O N Model SB1027 Spindle Brake To avoid the risk of gear damage, always start spindle rotation before using the autodownfeed rate selector. 7. Select one of the three downfeed rates by pulling the auto-downfeed rate selector knob out, position the selector over the appropriate detent, then release the knob. Make sure the pin is firmly seated by attempting to move the selector without pulling the knob out.
Model SB1027 O P E R AT I O N Loading/Unloading Tooling 5. For Machines Mfg. Since 8/09 With one hand holding the tool in place, insert the drawbar into the spindle from the top of the head, then thread it into the tool (see Figure 44). The mill is equipped with an R8 spindle taper and a 1⁄2"-20 x 18 1⁄2" spindle drawbar, as shown in Figure 43. Drawbar Figure 44. Drawbar loaded into the spindle. 6. Figure 43. Spindle drawbar and spacer. Tool Needed Qty Wrench 21mm..................................
For Machines Mfg. Since 8/09 MAINTENANCE Model SB1027 Maintenance Schedule Machine Storage ! Before Beginning Operations Always disconnect machine from power before performing maintenance or serious personal injury may result. Each operator of this machine is responsible for ensuring proper care of the equipment. We strongly recommend that all operators make a habit of following the daily maintenance procedures.
-42- 2 3 4 5 6 (360) 734-1540 • FAX: (360) 676-1075 www.southbendlathe.com 1 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Month/Year: Make copies of this page to use each month. Keep each charts as a maintenance record for the mill. Use this chart to keep track of the maintenance performed on the mill. Cross out or initial the “Day” box for each item on the list. If the box is blacked out, maintenance is not required for that item on that day.
For Machines Mfg. Since 8/09 MAINTENANCE Model SB1027 Cleaning Lubrication Regular cleaning is one of the most important steps in taking good care of this machine. Each operator is responsible for cleaning the machine immediately after using it or at the end of the day. We recommend that the cleaning routine be planned into the workflow schedule, so that adequate time is set aside to do the job right.
Model SB1027 MAINTENANCE For Machines Mfg. Since 8/09 Table Ways (One-Shot Oiler) Failure to follow reasonable lubrication practices as instructed in this manual for the mill could lead to premature failure of the mill and will void the warranty. Quill Oil Type....... Mobil Vactra 2 or ISO 68 Equivalent Oil Amount........................................... Fill Oil Cup Check/Add Frequency...............4 hrs. of Operation Lift the oil cup cap shown in Figure 46 to fill the oil cup with lubricant.
For Machines Mfg. Since 8/09 MAINTENANCE Model SB1027 Speed Range Bearing Sleeve Ram Ways Oil Type....... Mobil Vactra 2 or ISO 68 Equivalent Oil Amount........................................... Fill Oil Cup Check/Add Frequency.............40 hrs. of Operation Oil Type....... Mobil Vactra 2 or ISO 68 Equivalent Oil Amount.............................................. Thin Coat Check/Add Frequency.............40 hrs.
Model SB1027 MAINTENANCE For Machines Mfg. Since 8/09 Table Elevation Leadscrew Power Feed Gears Grease Type..........................NLGI 2 or Equivalent Grease Amount....................................... Thin Coat Check/Add Frequency.............40 hrs. of Operation Grease Type........Medium-Weight Lithium Grease Grease Amount............Two Pumps of Grease Gun Check/Add Frequency.............40 hrs.
MAINTENANCE For Machines Mfg. Since 8/09 4. Remove the brass bevel gear from the leadscrew, then remove the leadscrew alignment key (see Figure 54). Alignment Key Brass Bevel Gear Figure 54. Power feed brass gear and leadscrew alignment key. 5. Model SB1027 6. Replace the leadscrew alignment key, then align the bevel gear keyway with the key as you slide the gear onto the leadscrew and mesh its teeth with the drive gear. 7.
MAINTENANCE Model SB1027 Coolant Reservoir For Machines Mfg. Since 8/09 To check the coolant level: 1. DISCONNECT MILL FROM POWER! 2. Clean away debris and grime from the coolant drain screens on the base of the mill (see Figure 56), then insert a clean and dry piece of wire through one of the screens to check the level of the coolant. BIOLOGICAL & POISON HAZARD! Use the correct personal protection equipment when handling cutting fluid.
For Machines Mfg. Since 8/09 MAINTENANCE 5. The coolant reservoir on this mill is only designed to store coolant. During storage some fluids grow dangerous microbes, which will produce an unpleasant odor. As well, due to the collection of toxic metal chips in the fluid, the fluid can become a potent and extremely poisonous solution to humans and animals. Use the correct personal protection equipment and immediately change the coolant if either of these conditions occur.
Model SB1027 MAINTENANCE For Machines Mfg. Since 8/09 Machine Storage Adjusting Gibs To avoid rust problems or corrosion damage, use the following information to protect your investment when storing the mill for any length of time. Gibs are tapered lengths of metal between two dovetail sliding surfaces. Gibs control the gap between these surfaces and how they slide past one another. Correctly adjusting the gibs is critical to producing good milling results.
For Machines Mfg. Since 8/09 SERVICE Model SB1027 Adjusting Leadscrew Backlash Leadscrew backlash is the amount the leadscrew rotates before the attached device begins to move. Table Gib & Adjustment Screw Figure 58. Table gib and adjustment screw underneath the left side of the table. Although the mill is equipped with doublebronzed longitudinal and cross leadscrew nuts to minimize backlash, leadscrews will always have a certain amount of backlash that will increase with normal wear. Generally, 0.
Model SB1027 SERVICE Longitudinal Leadscrew Backlash 1. DISCONNECT MILL FROM POWER! 2. Loosen the two cap screws on the leadscrew nut accessed from underneath the left side of the table, as shown in Figure 61. 3. For Machines Mfg. Since 8/09 Unthread and remove the knurled retaining ring, graduated dial ring, and the leadscrew key, as shown in Figure 62. Cross Leadscrew Leadscrew Nut (1 of 2) & Cap Screw Figure 61.
For Machines Mfg. Since 8/09 5. SERVICE Loosen the two cap screws on the face of the leadscrew nut shown in Figure 64. Model SB1027 Belt Tensioning Power is transferred from the motor to the spindle with heavy-duty ribbed belts. With normal use, these belts will gradually stretch over time. When they do, perform the follow procedure to re-tension them. Tools Needed Qty Hex Wrench 6mm.................................................. 1 Hex Wrench 10mm................................................
TROU B LESHOOTI NG Model SB1027 For Machines Mfg. Since 8/09 If you need replacement parts, or if you are unsure how to do any of the solutions given here, feel free to call us at (360) 734-1540. ! Symptom Machine does not start or a breaker trips. Machine stalls or is overloaded. Possible Cause 1. Emergency stop button is pushed in or is at fault. 1. Rotate the button clockwise until it pops out; replace if necessary. 2. Main power switch not turned ON. 2.
For Machines Mfg. Since 8/09 Symptom Tool slips in collect. Tool breakage. Workpiece chatters or vibrates during operation. Table hard to move. Bad surface finish. Power feed chatters or grinds during operation. TROU B LESHOOTI NG Possible Cause Model SB1027 ! Possible Solution 1. Collet is not fully drawn into spindle taper. 1. Snug up the drawbar to fully seat the collet. 2. Wrong size collet. 2. Use correct collect for tool shank diameter. 3. Debris on mating surfaces of collet and spindle.
ELECTRICAL Model SB1027 For Machines Mfg. Since 8/09 Electrical Safety Instructions These pages are accurate at the time of printing. In the constant effort to improve, however, we may make changes to the electrical systems of future machines. Study this section carefully. If you see differences between your machine and what is shown in this section, call Technical Support at (360) 734-1540 for assistance BEFORE making any changes to the wiring on the machine. 1. 2.
For Machines Mfg.
ELECTRICAL Model SB1027 For Machines Mfg.
ELECTRICAL For Machines Mfg.
Model SB1027 ELECTRICAL For Machines Mfg. Since 8/09 Electrical Component Pictures Figure 66. Control panel wiring. Figure 68. Spindle motor wiring. Figure 69. Spindle brake switch wiring. Figure 67. Electrical panel wiring. Figure 70. Coolant pump motor wiring.
85 84 87 18 63 9 22 38 21 58 60 81 59 44 82 79 77 78 76 68 54 69 55A 61 81 80 86 83 19 62 45 37A 38 56 55 42 70 71 66 54 73A 72 55 40 67 73 75 74 57 43 46 47 48 41 39 21 65 64 53 37 89 139 52 50 49 51 49 38 88 90 36 35 104 105 65 101 17 15 103 102 100 14 13 9 21 109 107 112 129 10 106 113 99 12 11 22 20 9 8 110 18 7 127 138 133A 134 125 128 124 2 137 3 133 136 6 5 4 122 123 132 127A 126 131 135 18 1
PARTS Model SB1027 For Machines Mfg.
For Machines Mfg.
PARTS Model SB1027 For Machines Mfg.
PARTS For Machines Mfg.
PARTS Model SB1027 For Machines Mfg.
PARTS For Machines Mfg.
PARTS Model SB1027 For Machines Mfg.
PARTS For Machines Mfg.
-70- 608 608 656* 658 660 661 657 628 662 635 636 637 639 638 641 640 653 642 643 644 603 652 651 659 663 634 664* 633 630 631 632 608 619 628 622 620 626* 608 624 605 625 615 613A 616 613 612 614 610 607 609 611 623 617 621 629 605 608 628 627* 619A 618 607 665 667 601 606 605 604 603 602 PARTS 643 650 654 651A 602 605 608 648 655 649 646 645 647 607 608 655 665 666 626A* Available only as a set Model SB1027 For Machines Mfg.
For Machines Mfg.
-72- 711 701 702 709 723 724 733 735 738 740‡ 731 734 739 710 732 723A 707 705 706 708 713 741 710 744* 725 729 730 718 704A 735 706 752 751 753 703 704 705 716 715 701 746 713 711 709 710 708 702 724 701 749 723 747 725 748 707 712 729 738 723A 709 707 730 731 732 745 714‡ 721 722 702 717 733 710 711 718 719 720 734 714A‡ Available only as a set 719 716 715 750 717 722 721 720 736* 737 713 705 PARTS 704 704A 742* 743‡ 71
For Machines Mfg.
PARTS Model SB1027 For Machines Mfg. Since 8/09 One-Shot Oiler 807 801 802 801 808 803 K 806 K 804 805 Oil distributor B C 801 F G A B C D E F G H E D A H REF PART # DESCRIPTION REF PART # DESCRIPTION 801 802 803 804 PSB10240801 PSB10240802 PSB10240803 PCAP02M ELBOW JOINT M4 X 1/8 PT T-JOINT ONE SHOT OILER ASSEMBLY CAP SCREW M6-1 X 20 805 806 807 808 PCAP01M PSB10240806 PCAP38M PSB10240808 CAP SCREW M6-1 X 16 FLEXIBLE STEEL TUBE 4 X 500MM CAP SCREW M5-.
PARTS For Machines Mfg.
PARTS Model SB1027 For Machines Mfg.
For Machines Mfg.
PARTS Model SB1027 For Machines Mfg. Since 8/09 Tools 1101 1106 1107 1104 1103 1105 1102 REF PART # DESCRIPTION REF PART # DESCRIPTION 1101 1102 1103 1104 PSB10241004 PSDF2 PSDP2 PWR1214 TOOLBOX SCREWDRIVER FLAT #2 PHLP HD SCREWDRIVER #2 WRENCH 12/14MM 1105 1106 1107 PWR1921C PAW1510M PSB10241007 CLOSED WRENCH 19/21MM HEX WRENCH 10PC 1.
PARTS For Machines Mfg.
PARTS Model SB1027 For Machines Mfg.
WAR R ANT Y This quality product is warranted by South Bend Lathe Company to the original buyer for one year from the date of purchase. This warranty does not apply to consumable parts, or defects due to any kind of misuse, abuse, negligence, accidents, repairs, alterations or lack of maintenance. We do not reimburse for third party repairs.
South Bend Lathe Co. P.O. Box 2027 Bellingham, WA 98227 PHONE: (360) 734-1540 (Administrative Offices) FAX: (360) 676-1075 (International) FAX: (360) 734-1639 (USA only) southbendlathe.
