MODEL : STm.57b MOBILE PRINTER Rev. 1.
Table of Contents RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION 1. Unpacking 2 2. Product overview 3 3. Installation & Usage 4 3-1. Control Panel Usage 4 3-2. Battery Installation 5 3-3. Battery removel 6 3-4. Battery Charging 7 3-5. Battery Charger Usage 8 3-6. Usage of Cigar Jack for charging 9 3-7. Belt clip usage 10 3-8. Roll Paper Installation 11 3-9. Leather case Usage 12 3-10.
2. Product overview 1.
3. Setting Up the Product 3-2. Installing battery 3-1. Control Panel Usage Button Name function Power button This button is used to turn the printer on and off. When the printer is off, press this button for approximately 2 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off. Paper Feed Button Paper output can be done manually by pressing this button. Additionally, self-testing and Hexadecimal Dumping can be processed.. 1.
3-3. Battery removel 3-4. Battery Charging ② LED ① Push the Open into the direction indicated with the arrow in the image. Push up the hook after opening the battery cover. 1 2 3 1. The battery can be charged only when the temperature is 0~40℃ 2. Be sure that the printer is turn off and the battery to be charged is installed. 3. Connect the charger to the printer. 4. Recharging will now be started.
3-5. Battery charger Usage 3-6 Usage of Cigar Jack Charger for charging Optional Optional ② LED Printer ① 1. Please press the battery into the holder until you can hear a snapping sound. 2. Insert DC JACK ① into the end completely as the direct shown above. 3. Plug the power code to electrical outlet. 4. While charging the battery, red light turns on. Once the charge is completed, green light turns on. Check the state of code connection when error occurs blinking on red light.
3-7. Belt clip Usage 3-8. Roll Paper Installation Insert the belt hook screw into the hole of the belt hook. 1 2 As shown above, fasten the screw with a screw driver. 10 Open the paper cover pressing the open button. Insert a sharp tool into the paper guide hole and push it in the direction of arrow as shown above. Pull out a short length of the paper and shut the paper cover. 1 2 3 4 Put the paper in the right direction after adjusting the paper guide matching the paper width.
3-9. Leather Case Usage 3-10. Shoulder Strap Usage Optional Optional Open the Velcro 1 2 3 Put the printer into the leather case following the direction shown in the image. Close the Velcro 12 Insert the strap into the hook on the printer. Place the end of strap into the hook of shoulder strap. 1 2 3 4 After pulling out the end of strap tightly, put it into the clip to be fastened. Fasten the strap in the opposite side with the sample way.
3-11. Self Test Turn off the power pressing the power button for approximately 3 seconds. The sample of self test printout While you are pressing the FEED button, press the power button 1 2 3 NOTE 1. To print ASCII pattern additionally, press the Feed button once more 2. After printing ASCII pattern, the self test will be finished automatically. 3. If the Feed button is not pressed to print ASCII pattern, self test will be finished automatically after 30 seconds. The printout is produced.
4. Peripherals Connection When the printer is installed initially or when you face a problem, you can run the self test and check the information about -Control Circuit, Mechanism, Print Quality, ROM Version This product can communicate with other devices via Bluetooth communication and cable. 4-1. Bluetooth Connection After checking with self-test and no issues are found, you can examine other devices and software. This function is working independent of devices and software.
5. Printer cleaning If the interior of the printer is dusty, printing quality can lowered. In such a case, follow the instructions below to clean up the printer. 4-2. Interface Cable Connection NOTE 1. Make sure to turn the printer power off prior to cleaning 2. Regarding print head cleaning, as the print head sets very hot during printing, turn off the printer power and wait approximately 10 minute before commencement. 3.
6. Pritner Specification 6-1.
7. CPCL Command Compatibility NOTE Compatible Graphics Compatible with only commanders provided by the manufacturer.
Line Print Mode 24 Compatibility SETLP ○ SETLF ○ Moving With X and Y Coordinates ○ LMARGIN ○ SETBOLD ○ SETSP ○ Special ASCII Characters ○ SETFF ○ SET-TOF ○ SETLP-TIMEOUT ○
