User Manual

ManualsBrandsSource Audio ManualsDelays - EcoSA263 Collider Delay + Reverb - DELAY EFFECT + PEDAL REVERB

Table Of Contents

Welcome
Overview
Connecting the Pedal
- Power
Connections
- Guitar/Audio Connections
- Input Side Connections
- Output Side Connections
- Power and Control Connections
Reverb Engines
- Room
- Hall
- True Spring
- Plate
- Shimmer
- E-Dome
- Swell
Delay Engines
- Digital (0)
- Analog
- Tape
- Reverse
- Oil Can
Controls
- KNOBS Toggle Switch
- Effect Engine Selector Encoder & LEDs
  - DELAY/TAP Footswitch
- Tap Beat Division Toggle Switch
- REVERB Footswitch
- Control Input Button
  - External Control LED
Hardware Shortcuts
- Normal Mode Shortcuts
- Power-Up Shortcuts
Preset Storage and Recall
- Recalling Presets
- Recalling MIDI Presets
- Copying a Preset to a New Location Using the Select/(Hold) Save Button
- Copying a Preset to a New Location Using an External MIDI Controller
- Copying a Preset to a New Location Using the Neuro App
- Clearing all Presets
Universal Bypass
Stereo Operation & Signal Routing
- Mono In, Mono Out
- Mono In, Stereo Out
- Stereo In, Stereo Out
- Stereo In, Mono Out
- Stereo In, Stereo Out (Split Stereo)
External Control
- External Switches (1/4” TRS Connection)
- External Switches (1/8” TRRS Connection)
- External Expression Controller (1/4” TRS Connection – PEDAL IN jack)
- External Expression Controller (1/8”/3.5mm TRRS Connection – CONTROL INPUT jack)
Neuro Desktop and Mobile Editors
The Neuro Desktop Editor
- Downloading and Connecting the Neuro Desktop Editor
- Neuro Desktop Editor User Interface
- Connections
- Hardware Options
- Delay Controls (Engine A)
- Reverb Controls (Engine B)
- Routing Options
- Tap Tempo
- This section allows you to manually enter a tempo for your Delay repeats. You may type in a BPM (beats per minute) or ms (milli-seconds) numerically or use your cursor to “tap” the button at your desired tempo. Also in this section is the option to Sy...
- External Control
- Presets
- Device Tab
- Cloud Tab
The Neuro Mobile App
Neuro Hub
MIDI
- MIDI Channel
- Selecting Presets via Program Change (PC) Messages
- Controlling the Collider with MIDI Continuous Controller (CC) Messages
- Custom CC Mapping
USB
- USB-MIDI
Specifications
- Dimensions
- Weight
- Power
- Audio Performance
Troubleshooting
- Restore Factory Settings
- Noise
- Hot Hand Doesn’t Work
- Unit Appears Dead / No LEDs Lit
Frequently Asked Questions
- What kind of instruments can I connect to the Collider’s inputs?
- Can I power the Collider directly over USB, without using the 9 Volt supply?
- When connecting the Collider to a recording interface or mixer, should I used a Lo-Z (microphone) or Hi-Z (line / instrument) input?
- Why doesn’t the Collider respond to MIDI messages being sent to it?
- Can I use the Collider in my amp’s effects loop?
- How do I update the firmware?
  - Mac Gatekeeper
Rubber Feet
Waste Disposal Notes
Warranty
- Limited Transferrable Warranty
- Warranty Information
- Disclaimer and Limitation of Warranty
Version History

SA263 Collider Delay+Reverb Owner’s Manual

Full MIDI Implementation – Collider’s parameters can be accessed and controlled using MIDI

messages via its 5-pin DIN Input, a Neuro Hub connection, or USB port. Use MIDI messages to

engage/disengage the pedal, change presets, move parameters with a MIDI expression controller,

and more. Class compliant USB-MIDI allows the Collider to work as a plug-and-play device with

recording software running on Mac and Windows.

External Control – Easily configure the Collider to work with a variety of expression pedals and

footswitches for various external control options

Discover Knobs Position – Allows you to “discover” where the pedal’s knobs are set for a given

preset, via the Control LED flashing when you’ve reached the correct knob position on the dial.