User Manual

ManualsBrandsSource Audio ManualsDelays - EcoSA263 Collider Delay + Reverb - DELAY EFFECT + PEDAL REVERB

Table Of Contents

Welcome
Overview
Connecting the Pedal
- Power
Connections
- Guitar/Audio Connections
- Input Side Connections
- Output Side Connections
- Power and Control Connections
Reverb Engines
- Room
- Hall
- True Spring
- Plate
- Shimmer
- E-Dome
- Swell
Delay Engines
- Digital (0)
- Analog
- Tape
- Reverse
- Oil Can
Controls
- KNOBS Toggle Switch
- Effect Engine Selector Encoder & LEDs
  - DELAY/TAP Footswitch
- Tap Beat Division Toggle Switch
- REVERB Footswitch
- Control Input Button
  - External Control LED
Hardware Shortcuts
- Normal Mode Shortcuts
- Power-Up Shortcuts
Preset Storage and Recall
- Recalling Presets
- Recalling MIDI Presets
- Copying a Preset to a New Location Using the Select/(Hold) Save Button
- Copying a Preset to a New Location Using an External MIDI Controller
- Copying a Preset to a New Location Using the Neuro App
- Clearing all Presets
Universal Bypass
Stereo Operation & Signal Routing
- Mono In, Mono Out
- Mono In, Stereo Out
- Stereo In, Stereo Out
- Stereo In, Mono Out
- Stereo In, Stereo Out (Split Stereo)
External Control
- External Switches (1/4” TRS Connection)
- External Switches (1/8” TRRS Connection)
- External Expression Controller (1/4” TRS Connection – PEDAL IN jack)
- External Expression Controller (1/8”/3.5mm TRRS Connection – CONTROL INPUT jack)
Neuro Desktop and Mobile Editors
The Neuro Desktop Editor
- Downloading and Connecting the Neuro Desktop Editor
- Neuro Desktop Editor User Interface
- Connections
- Hardware Options
- Delay Controls (Engine A)
- Reverb Controls (Engine B)
- Routing Options
- Tap Tempo
- This section allows you to manually enter a tempo for your Delay repeats. You may type in a BPM (beats per minute) or ms (milli-seconds) numerically or use your cursor to “tap” the button at your desired tempo. Also in this section is the option to Sy...
- External Control
- Presets
- Device Tab
- Cloud Tab
The Neuro Mobile App
Neuro Hub
MIDI
- MIDI Channel
- Selecting Presets via Program Change (PC) Messages
- Controlling the Collider with MIDI Continuous Controller (CC) Messages
- Custom CC Mapping
USB
- USB-MIDI
Specifications
- Dimensions
- Weight
- Power
- Audio Performance
Troubleshooting
- Restore Factory Settings
- Noise
- Hot Hand Doesn’t Work
- Unit Appears Dead / No LEDs Lit
Frequently Asked Questions
- What kind of instruments can I connect to the Collider’s inputs?
- Can I power the Collider directly over USB, without using the 9 Volt supply?
- When connecting the Collider to a recording interface or mixer, should I used a Lo-Z (microphone) or Hi-Z (line / instrument) input?
- Why doesn’t the Collider respond to MIDI messages being sent to it?
- Can I use the Collider in my amp’s effects loop?
- How do I update the firmware?
  - Mac Gatekeeper
Rubber Feet
Waste Disposal Notes
Warranty
- Limited Transferrable Warranty
- Warranty Information
- Disclaimer and Limitation of Warranty
Version History

SA263 Collider Delay+Reverb Owner’s Manual

Split Stereo Modes

An additional option is available when using the Collider in Parallel Mode. In the Routing Options

block of the Neuro Editors there is a button labeled “Split Stereo (Left=A, Right=B). This option

provides independent processing, meaning you can apply only delay to Input and Output 1 and only

Reverb to Input and Output 2. See detailed descriptions of the Split Stereo options in the section

below.

• Mono In, Stereo Out (Split Stereo)

• Stereo In, Stereo Out (Split Stereo)

Mono In, Stereo Out (Split Stereo)

This mode is used when routing a single mono signal to Split Stereo (Left=A, Right=B).