User Manual

ManualsBrandsSource Audio ManualsDelays - EcoSA263 Collider Delay + Reverb - DELAY EFFECT + PEDAL REVERB

Table Of Contents

Welcome
Overview
Connecting the Pedal
- Power
Connections
- Guitar/Audio Connections
- Input Side Connections
- Output Side Connections
- Power and Control Connections
Reverb Engines
- Room
- Hall
- True Spring
- Plate
- Shimmer
- E-Dome
- Swell
Delay Engines
- Digital (0)
- Analog
- Tape
- Reverse
- Oil Can
Controls
- KNOBS Toggle Switch
- Effect Engine Selector Encoder & LEDs
  - DELAY/TAP Footswitch
- Tap Beat Division Toggle Switch
- REVERB Footswitch
- Control Input Button
  - External Control LED
Hardware Shortcuts
- Normal Mode Shortcuts
- Power-Up Shortcuts
Preset Storage and Recall
- Recalling Presets
- Recalling MIDI Presets
- Copying a Preset to a New Location Using the Select/(Hold) Save Button
- Copying a Preset to a New Location Using an External MIDI Controller
- Copying a Preset to a New Location Using the Neuro App
- Clearing all Presets
Universal Bypass
Stereo Operation & Signal Routing
- Mono In, Mono Out
- Mono In, Stereo Out
- Stereo In, Stereo Out
- Stereo In, Mono Out
- Stereo In, Stereo Out (Split Stereo)
External Control
- External Switches (1/4” TRS Connection)
- External Switches (1/8” TRRS Connection)
- External Expression Controller (1/4” TRS Connection – PEDAL IN jack)
- External Expression Controller (1/8”/3.5mm TRRS Connection – CONTROL INPUT jack)
Neuro Desktop and Mobile Editors
The Neuro Desktop Editor
- Downloading and Connecting the Neuro Desktop Editor
- Neuro Desktop Editor User Interface
- Connections
- Hardware Options
- Delay Controls (Engine A)
- Reverb Controls (Engine B)
- Routing Options
- Tap Tempo
- This section allows you to manually enter a tempo for your Delay repeats. You may type in a BPM (beats per minute) or ms (milli-seconds) numerically or use your cursor to “tap” the button at your desired tempo. Also in this section is the option to Sy...
- External Control
- Presets
- Device Tab
- Cloud Tab
The Neuro Mobile App
Neuro Hub
MIDI
- MIDI Channel
- Selecting Presets via Program Change (PC) Messages
- Controlling the Collider with MIDI Continuous Controller (CC) Messages
- Custom CC Mapping
USB
- USB-MIDI
Specifications
- Dimensions
- Weight
- Power
- Audio Performance
Troubleshooting
- Restore Factory Settings
- Noise
- Hot Hand Doesn’t Work
- Unit Appears Dead / No LEDs Lit
Frequently Asked Questions
- What kind of instruments can I connect to the Collider’s inputs?
- Can I power the Collider directly over USB, without using the 9 Volt supply?
- When connecting the Collider to a recording interface or mixer, should I used a Lo-Z (microphone) or Hi-Z (line / instrument) input?
- Why doesn’t the Collider respond to MIDI messages being sent to it?
- Can I use the Collider in my amp’s effects loop?
- How do I update the firmware?
  - Mac Gatekeeper
Rubber Feet
Waste Disposal Notes
Warranty
- Limited Transferrable Warranty
- Warranty Information
- Disclaimer and Limitation of Warranty
Version History

SA263 Collider Delay+Reverb Owner’s Manual

Stereo In, Stereo Out

This mode should be your default selection for Stereo In, Stereo Out applications. Most effective

stereo reverb processing is performed with information from both input channels, so the modes in

this section should not be considered as completely independent audio channels. If you want

channel independence, set the Routing Option to “Parallel Delay/Reverb” and choose the “Split

Stereo (Left=A, Right=B)” option