User Manual
Table Of Contents
- Welcome
- Overview
- Connecting the Pedal
- Connections
- Reverb Engines
- Delay Engines
- Controls
- Hardware Shortcuts
- Preset Storage and Recall
- Universal Bypass
- Stereo Operation & Signal Routing
- External Control
- Neuro Desktop and Mobile Editors
- The Neuro Desktop Editor
- Downloading and Connecting the Neuro Desktop Editor
- Neuro Desktop Editor User Interface
- Connections
- Hardware Options
- Delay Controls (Engine A)
- Reverb Controls (Engine B)
- Routing Options
- Tap Tempo
- This section allows you to manually enter a tempo for your Delay repeats. You may type in a BPM (beats per minute) or ms (milli-seconds) numerically or use your cursor to “tap” the button at your desired tempo. Also in this section is the option to Sy...
- External Control
- Presets
- Device Tab
- Cloud Tab
- The Neuro Mobile App
- Neuro Hub
- MIDI
- USB
- Specifications
- Troubleshooting
- Frequently Asked Questions
- What kind of instruments can I connect to the Collider’s inputs?
- Can I power the Collider directly over USB, without using the 9 Volt supply?
- When connecting the Collider to a recording interface or mixer, should I used a Lo-Z (microphone) or Hi-Z (line / instrument) input?
- Why doesn’t the Collider respond to MIDI messages being sent to it?
- Can I use the Collider in my amp’s effects loop?
- How do I update the firmware?
- Rubber Feet
- Waste Disposal Notes
- Warranty
- Version History
SA263 Collider Delay+Reverb Owner’s Manual
18
Hardware Shortcuts
The Collider comes with many “hidden” controls and features that will help you calibrate the pedal to
your specific needs. There are two types of shortcuts: “Normal” shortcuts that are done without
changing the power of the pedal, and “Power-Up” shortcuts that are options set by depowering and
repowering the pedal.
Normal Mode Shortcuts
Trails Mode: To toggle Trails Mode for your delay/reverb, hold the CONTROL INPUT button on
the top side of the pedal, and press the DELAY/TAP switch. The Control Indicator LED will flash
once for Trails Mode OFF, and twice for Trails Mode ON.
Preset Extension Mode: To toggle Preset Extension Mode, which doubles the amount of
available preset slots from 4 to 8, hold the CONTROL INPUT button on the top side of the pedal,
and press the PRESET SELECT Button.
Adjust Delay Time Division: To toggle between stereo delay time divisions, hold the CONTROL
INPUT button while moving the DELAY knob. There are four divisions spread out evenly across
the knob.
Hidden Output Level Knob: To access the hidden “Output Level” knob, hold the CONTROL
INPUT button while moving the MIX knob. This will control the overall output of the Collider.
Unity gain is at 12 o’clock. This combination is also used to control the level of the dry signal
when the effects are in Parallel Mode.
Power-Up Shortcuts
Factory Reset: To perform a factory reset on the Collider, unplug the power cable. Then, press +
hold the REVERB Footswitch while plugging the power supply back in.
Disable Internal Tap: To disable the integrated Tap Tempo feature located on the DELAY/TAP
Footswitch, unplug the power cable. Then, press + hold the DELAY/TAP Footswitch while
plugging the power supply back in. The DELAY/TAP LED Indicator will flash once for disabled,
twice for enabled.
Control Input Jack Assign Options: To toggle between Control Input Jack assignments, unplug
the power cable. Then, press + hold the CONTROL INPUT Button while plugging the power
supply back in. Keep holding the CONTROL INPUT Button to cycle through the options. The
Control LED Indicator will flash once for Option 1 (Neuro Hub/Expression), twice for Option 2
(Preset Increment), three times for Option 3 (Preset Decrement), and four times for Option 4
(Tap). Release the CONTROL INPUIT Button to select one of these four options.