User Manual

ManualsBrandsSource Audio ManualsChorus - FlangerGemini Chorus - CHORUS EFFECT WITH PEDAL FOR GUITAR

Table Of Contents

Welcome
Overview
Quick Start
- Power
- Guitar/Audio Connections
- Brief Knob, Footswitch, and Button Descriptions
Connections
- Input Side Connections
  - Input 1
  - Input 2
    - Input 2 as an Audio Input
    - Input 2 as a Neuro App Data Input
- Output Side Connections
  - Output 1
  - Output 2
    - Output 2 as an Audio Output
    - Output 2 as a Neuro App Data Daisy-Chain Output
- Example Neuro Daisy-Chain Connections
  - Mono Audio Path with Neuro Daisy-Chain
  - Mono-To-Stereo Audio Path with Neuro Daisy-Chain
- Power and Control Connections
Basic Chorus Operation
Effect Types
- Classic
- Dual
- Quad
- Additional Effect Types
Controls
- Knobs
- Effect Switch
- LEDs
  - Engage / Bypass LED
  - External Control LED
- Footswitch
- Control Input Button
Preset Storage and Recall
- Saving Your First Preset
- Editing a Preset
- Exiting Preset Mode
- Quick Preset Switching
Universal Bypass TM
Stereo Routing
Parametric EQ
- Low Cut Filter
External Control
- Expression Control
Neuro App
- Main Menu
- Sound Editor
- Browse Sounds
  - Open In Sound Editor
  - Deleting or Publishing Presets
- Hardware Options
- Neuro Hub (Formerly the Soundblox Hub)
  - MIDI
- USB
  - USB-MIDI
- Envelope Mode
- External Tap Tempo
Specifications
- Dimensions
- Weight
- Power
- Audio Performance
Troubleshooting
- General
  - Factory Reset using the Neuro App
  - Factory Reset using the Hardware (Firmware v1.06 and later)
- Noise
- Hot Hand Doesn’t Work
- Unit Appears Dead / No LEDs Lit
Frequently Asked Questions
- How do I change the routing mode for my pedal without changing anything about the sounds?
- What kind of instruments can I connect to the Gemini’s inputs?
- Can I power the Gemini directly over USB, without using the 9 Volt supply?
- When connecting the Gemini to a recording interface or mixer, should I used a Lo-Z (microphone) or Hi-Z (line / instrument) input?
- Why doesn’t the Gemini respond to MIDI messages being sent to it?
- How do I enable extended effect types via MIDI?
- Can I use the Gemini in my amp’s effects loop?
Rubber Feet
Waste Disposal Notes
Warranty
- Limited Transferrable Warranty
- Warranty Information
- Disclaimer and Limitation of Warranty
Version History

SA242 Gemini Chorus User’s Guide 3

Quick Start

Power

To power the unit, connect the included 9V DC power supply to the jack labeled DC 9V on the back

panel.

Warning: Using a non-Source Audio supply, especially an unregulated supply, could damage the unit.

Please be very cautious when using 3

-party power supplies.

Guitar/Audio Connections

Using standard ¼” mono cables, connect your guitar, bass, or other instrument to the INPUT 1 jack

and your amp (or the next audio device in the signal chain) to the OUTPUT 1 jack.

When the power and audio connections have been made, the Gemini is ready to play.

Brief Knob, Footswitch, and Button Descriptions

Depth Knob: Controls the depth of the Low Frequency Oscillator (LFO), which determines the

strength or prominence of the chorus effect.

Speed Knob: Controls the frequency of the LFO, which determines the speed of the chorus effect.

Mix Knob: Sets the relative levels on the dry (clean input) signal and the wet effects signal, allowing

you to dial in just the right amount of chorus.

Tone Knob: Controls the tonal balance of the output, making either the treble or bass more

prominent.