User Manual

ManualsBrandsSource Audio ManualsChorus - FlangerGemini Chorus - CHORUS EFFECT WITH PEDAL FOR GUITAR

Table Of Contents

Welcome
Overview
Quick Start
- Power
- Guitar/Audio Connections
- Brief Knob, Footswitch, and Button Descriptions
Connections
- Input Side Connections
  - Input 1
  - Input 2
    - Input 2 as an Audio Input
    - Input 2 as a Neuro App Data Input
- Output Side Connections
  - Output 1
  - Output 2
    - Output 2 as an Audio Output
    - Output 2 as a Neuro App Data Daisy-Chain Output
- Example Neuro Daisy-Chain Connections
  - Mono Audio Path with Neuro Daisy-Chain
  - Mono-To-Stereo Audio Path with Neuro Daisy-Chain
- Power and Control Connections
Basic Chorus Operation
Effect Types
- Classic
- Dual
- Quad
- Additional Effect Types
Controls
- Knobs
- Effect Switch
- LEDs
  - Engage / Bypass LED
  - External Control LED
- Footswitch
- Control Input Button
Preset Storage and Recall
- Saving Your First Preset
- Editing a Preset
- Exiting Preset Mode
- Quick Preset Switching
Universal Bypass TM
Stereo Routing
Parametric EQ
- Low Cut Filter
External Control
- Expression Control
Neuro App
- Main Menu
- Sound Editor
- Browse Sounds
  - Open In Sound Editor
  - Deleting or Publishing Presets
- Hardware Options
- Neuro Hub (Formerly the Soundblox Hub)
  - MIDI
- USB
  - USB-MIDI
- Envelope Mode
- External Tap Tempo
Specifications
- Dimensions
- Weight
- Power
- Audio Performance
Troubleshooting
- General
  - Factory Reset using the Neuro App
  - Factory Reset using the Hardware (Firmware v1.06 and later)
- Noise
- Hot Hand Doesn’t Work
- Unit Appears Dead / No LEDs Lit
Frequently Asked Questions
- How do I change the routing mode for my pedal without changing anything about the sounds?
- What kind of instruments can I connect to the Gemini’s inputs?
- Can I power the Gemini directly over USB, without using the 9 Volt supply?
- When connecting the Gemini to a recording interface or mixer, should I used a Lo-Z (microphone) or Hi-Z (line / instrument) input?
- Why doesn’t the Gemini respond to MIDI messages being sent to it?
- How do I enable extended effect types via MIDI?
- Can I use the Gemini in my amp’s effects loop?
Rubber Feet
Waste Disposal Notes
Warranty
- Limited Transferrable Warranty
- Warranty Information
- Disclaimer and Limitation of Warranty
Version History

SA242 Gemini Chorus User’s Guide 26

Hardware Options

This screen shows some advanced options.

Effect Bypass Mode

Selects which bypass path will be used for presets that use hardware bypass mode.

 True Bypass (Relay) uses two relays for true bypass switching.

 Active Analog (Buffered) bypass uses a buffer to help prevent signal loss and clicking.

MIDI Channel (Device ID)

Selects which channel (1 to 16) the hardware will respond to on Hub and USB-MIDI inputs.

Preset Mode (Soundblox 2 Mode)

Enables the preset saved in memory to be loaded each time the effect is enabled using the

footswitch. This loads all settings from the preset and ignores the knob positions. When Preset Mode

is enabled, the main LED will be red instead of green. Preset Mode can also be enabled/disabled by

pressing and holding the footswitch for a few seconds.

Enable External Tap Tempo Switch

Allows the Source Audio tap tempo switch to be connected to the Control Input Port. This allows the

tempo for the LFO to be tapped in directly. The Control LED will blink in time with the tempo if this

mode is enabled.

Factory Reset

Resets the internal memory (including all presets and effect types) to the factory default settings.