User Manual
Table Of Contents
- Welcome
- Overview
- Quick Start
- Connections
- Reverb Engines
- Extended Reverb Engines
- Controls
- Preset Storage and Recall
- Recalling Presets
- Recalling MIDI Presets
- Editing and Saving a Single Engine Preset to Reverb A
- Editing and Saving a Dual Engine Preset to Reverb A+B
- Copying a Preset to a New Location Using the Select/(Hold) Save Button
- Copying a Preset to a New Location Using an External MIDI Controller
- Copying a Preset to a New Location Using the Neuro App
- Clearing all Presets
- Universal Bypass
- Stereo Operation & Signal Routing
- Mono In, Mono Out (1)
- Toggle = A Toggle = B
- Toggle = A+B, Dual Parallel
- Toggle = A+B, Dual Cascade
- Stereo In, Mono Out (2)
- Toggle = A Toggle = B
- Toggle = A+B, Dual Parallel
- Toggle = A+B, Dual Cascade
- Mono In, Stereo Out (3)
- Toggle = A Toggle = B
- Toggle = A+B, Dual Parallel
- Stereo In, Dependent Stereo Out (4)
- Toggle Switch = Reverb A Toggle Switch = Reverb B
- Toggle = Reverb A+B, Dual Cascade
- Mono In, Mono Out, Dry Out 2 (5)
- Toggle Switch = Reverb A Toggle Switch = Reverb B
- Toggle = Reverb A+B, Dual Cascade
- Stereo In, Wet Sum to Mono (6)
- Toggle Switch = Reverb A Toggle Switch = Reverb B
- Toggle = Reverb A+B, Dual Cascade
- Dual Mono, (Independent Stereo) (7)
- Toggle Switch = Reverb A Toggle Switch = Reverb B
- Mono In, Independent Stereo Out (8)
- Toggle Switch = Reverb A Toggle Switch = Reverb B
- Pre Processing External Loop (9)
- Toggle Switch = Reverb A Toggle Switch = Reverb B
- Toggle = Reverb A+B, Dual Cascade
- External Loop Cable Connection Instructions
- External Control
- Neuro Desktop and Mobile Editors
- The Neuro Desktop Editor
- Downloading and Connecting the Neuro Desktop Editor
- Neuro Desktop Editor User Interface
- Connections
- Hardware Options
- Sound Editor
- Dual/Single Mode
- I/O Routing Option
- Reverb Engine A Controls
- Option Footswitch Assign
- Tapping or holding the Ventris Dual Reverb’s OPTION footswitch accesses specific default functions, depending on the selected reverb engine (see the Reverb Engines section for the default functions of each engine). In addition, it is possible to reass...
- Reverb Engine B Controls
- Dual Mode Controls
- Spillover Controls
- On/Off Status (MIDI Recall)
- External Control
- Presets
- The Neuro Mobile App
- Neuro Hub
- MIDI
- USB
- Specifications
- Troubleshooting
- Frequently Asked Questions
- How can I access the extended reverb engines without the app?
- What kind of instruments can I connect to the Ventris’s inputs?
- Can I power the Ventris directly over USB, without using the 9 Volt supply?
- When connecting the Ventris to a recording interface or mixer, should I used a Lo-Z (microphone) or Hi-Z (line / instrument) input?
- Why doesn’t the Ventris respond to MIDI messages being sent to it?
- Can I use the Ventris in my amp’s effects loop?
- How do I update the firmware?
- Rubber Feet
- Waste Disposal Notes
- Warranty
- Version History
SA262 Ventris Dual Reverb Owner’s Manual
6
PRE-DELAY: Adjusts the amount of time between the dry signal and the beginning of the reverb. Turn
the PRE-DELAY knob clockwise to create echo reflections similar to slapback or delay effects.
MIX: Controls the relative level between the dry input signal and the wet. When set at 3 o'clock, the
wet and dry signals will be at equal volume. Fully counter-clockwise is 100% dry, and fully clockwise is
100% wet.
TREBLE: Controls the cut-off point of a low pass filter on the wet signal. Turn the knob clockwise for
brighter reverb trails and counter-clockwise for darker trails.
CONTROL 1 & CONTROL 2: The functions of these knobs vary depending on the selected reverb
engine. Check the Reverb Engines section of this manual for the parameter descriptions of each
CONTROL knob’s function.
ENGINE SELECTOR KNOB: Selects between the 12 main effect engines. To access the additional
reverb engines, use the Neuro Mobile App or Desktop Editor.
ON/OFF FOOTSWITCH: Engages or bypasses the reverb effect. The corresponding ON/OFF LED will be
lit when the reverb effect is engaged. In addition (while the pedal is engaged), pressing and holding
the ON/OFF Footswitch scrolls to the next Preset.
OPTION FOOTSWITCH (FOOTSWITCH #2): This dual action footswitch comes preloaded with two
independent control functions that vary depending on the selected engine. The footswitch responds
to two actions: quickly tapping, or press & hold. Each of the two actions prompts a different function.
See the Reverb Engines section for descriptions of each default control function. Option Footswitch
commands include tap tempo for the Pre-Delay or modulation, Hold, Build, A/B reverb toggling, and
more. It is also possible to program alternative control options with the Neuro App or Desktop Editor.
A/B REVERB SELECTOR TOGGLE SWITCH: Selects between reverbs A, B, or A+B. Save two
independent reverb effects (one for each processor) in each of the Ventris’s 128 presets and use the
A/B Toggle Switch to select which is active. Selecting A + B will engage both reverbs simultaneously.
Note: the initial engagement position of this switch can be saved as part of a preset. Go to the Editing
and Saving Dual Engine Presets section for complete instructions on dual reverb presets.
PRESET SELECT/SAVE BUTTON: Scrolls through the four user presets (or eight in Preset Extension
Mode) saved in the Ventris. To save a preset into the currently selected spot, press and hold this
button.
AUTOMATIC STEREO DETECTION: The Ventris monitors its Input and Output connections and
configures itself to the appropriate stereo routing mode. It is also possible to override this and
choose a custom routing mode using the Neuro Editors.