User Manual
Table Of Contents
- Welcome
- Overview
- Quick Start
- Connections
- Reverb Engines
- Extended Reverb Engines
- Controls
- Preset Storage and Recall
- Recalling Presets
- Recalling MIDI Presets
- Editing and Saving a Single Engine Preset to Reverb A
- Editing and Saving a Dual Engine Preset to Reverb A+B
- Copying a Preset to a New Location Using the Select/(Hold) Save Button
- Copying a Preset to a New Location Using an External MIDI Controller
- Copying a Preset to a New Location Using the Neuro App
- Clearing all Presets
- Universal Bypass
- Stereo Operation & Signal Routing
- Mono In, Mono Out (1)
- Toggle = A Toggle = B
- Toggle = A+B, Dual Parallel
- Toggle = A+B, Dual Cascade
- Stereo In, Mono Out (2)
- Toggle = A Toggle = B
- Toggle = A+B, Dual Parallel
- Toggle = A+B, Dual Cascade
- Mono In, Stereo Out (3)
- Toggle = A Toggle = B
- Toggle = A+B, Dual Parallel
- Stereo In, Dependent Stereo Out (4)
- Toggle Switch = Reverb A Toggle Switch = Reverb B
- Toggle = Reverb A+B, Dual Cascade
- Mono In, Mono Out, Dry Out 2 (5)
- Toggle Switch = Reverb A Toggle Switch = Reverb B
- Toggle = Reverb A+B, Dual Cascade
- Stereo In, Wet Sum to Mono (6)
- Toggle Switch = Reverb A Toggle Switch = Reverb B
- Toggle = Reverb A+B, Dual Cascade
- Dual Mono, (Independent Stereo) (7)
- Toggle Switch = Reverb A Toggle Switch = Reverb B
- Mono In, Independent Stereo Out (8)
- Toggle Switch = Reverb A Toggle Switch = Reverb B
- Pre Processing External Loop (9)
- Toggle Switch = Reverb A Toggle Switch = Reverb B
- Toggle = Reverb A+B, Dual Cascade
- External Loop Cable Connection Instructions
- External Control
- Neuro Desktop and Mobile Editors
- The Neuro Desktop Editor
- Downloading and Connecting the Neuro Desktop Editor
- Neuro Desktop Editor User Interface
- Connections
- Hardware Options
- Sound Editor
- Dual/Single Mode
- I/O Routing Option
- Reverb Engine A Controls
- Option Footswitch Assign
- Tapping or holding the Ventris Dual Reverb’s OPTION footswitch accesses specific default functions, depending on the selected reverb engine (see the Reverb Engines section for the default functions of each engine). In addition, it is possible to reass...
- Reverb Engine B Controls
- Dual Mode Controls
- Spillover Controls
- On/Off Status (MIDI Recall)
- External Control
- Presets
- The Neuro Mobile App
- Neuro Hub
- MIDI
- USB
- Specifications
- Troubleshooting
- Frequently Asked Questions
- How can I access the extended reverb engines without the app?
- What kind of instruments can I connect to the Ventris’s inputs?
- Can I power the Ventris directly over USB, without using the 9 Volt supply?
- When connecting the Ventris to a recording interface or mixer, should I used a Lo-Z (microphone) or Hi-Z (line / instrument) input?
- Why doesn’t the Ventris respond to MIDI messages being sent to it?
- Can I use the Ventris in my amp’s effects loop?
- How do I update the firmware?
- Rubber Feet
- Waste Disposal Notes
- Warranty
- Version History
SA262 Ventris Dual Reverb Owner’s Manual
29
Note: When recalling presets via MIDI PC messages, you may wish to queue up your preset with
effect bypassed. To do this, simply engage the preset, bypass it with the ON/OFF footswitch, then re-
save the preset normally. When recalled, the pedal will load the saved user settings, but the effect
will be bypassed. To engage the preset, simply press the ON/OFF Footswitch on the Ventris.
Copying a Preset to a New Location Using the Select/(Hold) Save Button
1. Select the preset you would like to copy by pressing the SELECT/(HOLD) SAVE Button until the
corresponding PRESET LED is lit.
2. Press and hold the SELECT/(HOLD) SAVE Button for one second until the corresponding PRESET
LED begins blinking rapidly. Quickly release the SELECT/(HOLD) SAVE Button. The PRESET LED
should continue to blink rapidly. This indicates that the Ventris is in copy mode.
3. Tap the SELECT/(HOLD) SAVE Button to increment the preset. The corresponding PRESET LED
should continue to blink rapidly. Tap the SELECT/(HOLD) SAVE Button again until the desired
copy destination is selected.
4. Press and hold the SELECT/(HOLD) SAVE Button until the PRESET LED blinks slowly and then turns
solid. This indicates that the preset has been saved to the new location. The original location
will not be changed or overwritten.
Copying a Preset to a New Location Using an External MIDI Controller
1. Select the preset you would like to copy by sending a MIDI program change message to the
Ventris.
2. Press and hold the SELECT/(HOLD) SAVE Button for one second until the corresponding PRESET
LED begins blinking rapidly. Quickly release the SELECT/(HOLD) SAVE Button. The PRESET LED(S)
should continue to blink rapidly. This indicates that the Ventris is in copy mode.
3. Send a desired MIDI Program Change number to indicate the desired copy destination for the
preset.
4. PRESET LED will blink fast and then turn solid. This indicates that the preset has been saved to
the new location.
Copying a Preset to a New Location Using the Neuro App
Using the BURN command in Neuro Mobile or Desktop Editors, it is possible to copy presets to any
location in memory.
Clearing all Presets
The entire range of 128 User Presets can be erased using the Factory Reset procedure. Warning: the
Factory Reset procedure resets the entire pedal back to the state in which it was originally shipped –
this includes all global settings, swapped reverb engines in the Effect Selector knob, and User Presets.
A Factory Reset will not change any firmware updates.