User Manual

ManualsBrandsSource Audio ManualsEqualizersEQ2 Programmable EQ - PROGRAMMABLE PEDAL EQUALIZER FOR GUITAR

Table Of Contents

Welcome
Contents
Feature Overview
Connecting the Pedal
- Power
Connections
- Guitar/Audio Connections
- Input Side Connections
- Output Side Connections
- Power and Control Connections
Basic Operation
- Selecting a Band to Adjust
- Adjusting a Band
- Set to Flat
- Adjusting the Frequency of a Band
- Adjusting the Q Factor (Width) of a Band
- Setting the Master Output
The Options Menu
Navigating the Options Menu
- FREQ
- Q FACT
- GAIN
- SPLIT
- LIMITER
- GATE
- THRESHOLD
- HP FREQ
- SHELF (Bands 1 and 10 Only)
- CONFIG
- MIDI CH
- FS Option
- CNTRL OPTION
Controls
- Rotary Encoder Knob
- OUTPUT Knob
- Footswitch
- Control Input Button
- ON/OFF LED
- Preset SELECT/SAVE Button & Preset LEDs
- Display Screen
Common EQ Configurations
- Vocal Mid-Bump, Mild Bass Reduction
- “Arrow” Configuration (Drastic Mid Push)
- Drastic Mid Scoop
- Subtle Mid Scoop
- Mild Bass Boost, Treble Roll-Off
- Single Coil Sanctuary
Stereo Operation & Signal Routing
- Mono In, Mono Out
- Mono In, Stereo Out
- Stereo In, Stereo Out
- Stereo In, Mono Out
Preset Storage and Recall
- Recalling Presets
- Recalling MIDI Presets
- Copying a Preset to a New Location Using the Select/(Hold) Save Button
- Copying a Preset to a New Location Using an External MIDI Controller
- Copying a Preset to a New Location Using the Neuro App
- Clearing all Presets
Additional Features
- Noise Gate
- Limiter
- “Split” Mode
- Tuner
External Control
- External Switch Options
- External Switches (1/8” TRRS Connection)
Expression Control
- Connecting the Expression Pedal
- Mapping Parameters
- MIDI
Neuro Desktop and Mobile Editors
The Neuro Desktop Editor
- Downloading and Connecting the Neuro Desktop Editor
- Neuro Desktop Editor User Interface
- Connections
- Hardware Options
- Equalizer
- Master Volume & Trim
- Limiter
- Noise Gate
- I/O Routing Options
- External Switch
- External Control
- Presets
The Neuro Mobile App — with New Direct MIDI-USB Support
- Connecting to the Neuro Mobile App (USB-MIDI)
- Connecting to the Neuro Mobile App (headphone jack)
Neuro Hub
MIDI
- MIDI Channel
- Selecting Presets via Program Change (PC) Messages
- Controlling the EQ2 with MIDI Continuous Controller (CC) Messages
- Custom CC Mapping
USB
- USB-MIDI
Specifications
- Dimensions
- Weight
- Power
- Audio Performance
Troubleshooting
- Restore Factory Settings
- Noise/Hum
- Unit Appears Dead / No LEDs Lit
Frequently Asked Questions
- What kind of instruments can I connect to the EQ2’s inputs?
- Can I power the EQ2 directly over USB, without using the 9 Volt supply?
- When connecting the EQ2 to a recording interface or mixer, should I use a Lo-Z (microphone) or Hi-Z (line / instrument) input?
- Why doesn’t the EQ2 respond to MIDI messages being sent to it?
- Can I use the EQ2 in my amp’s effects loop?
- How do I update the firmware?
  - Mac isn’t letting me download your software?
Rubber Feet
Waste Disposal Notes
Warranty
- Limited Transferrable Warranty
- Warranty Information
- Disclaimer and Limitation of Warranty
Version History

SA270 EQ2 User Guide

Stereo In, Stereo Out

This mode should be your default selection for Stereo In, Stereo Out applications. Stereo In, Stereo

Out allows you to continue your stereo chain of effects.

Stereo In, Mono Out

This mode will accept stereo input on jacks INPUT 1 and 2. Inputs 1 and 2 are sent to Channel 1 and 2

equalizers, respectively. The outputs of the Channel 1 and Channel 2 equalizers are mixed together

and sent to OUTPUT 1.

Additional Routing Modes

EQ2 supports an additional routing mode available in the Neuro Mobile App and the Neuro Desktop

Editor, External Loop 2 -> Loop 1.

External Loop 2 -> Loop 1

This routing mode supports a use case that involves placing two different EQs at two different points

in your signal path. In this routing mode, a loop for external effects is placed after Channel 2, before

Channel 1. INPUT 2 and OUTPUT 2 act as “Send” and “Return” for the effects loop.