Owner's Manual
Functions
&
Controls
RS5.4500D
HP PASS
(HighPass)
CH1/2
Controls the frequency response
of
your speakers downwards. The Cut-off frequency is continously variable from 1 0Hz up to 150Hz
HP PASS (High Pass)
CH3/4
Controls the frequency response
of
your
speekers downwards. The Cut-of frequency is comtinously variable from 1 0Hz up to 150Hz
LOWPASSCH5
Controls the frequency response
of
your speakers upwards. The Cut off frequency is continously variable fram 30Hz up to 150Hz
Level
This
allows
to
adjust
the
input
Mode
sensitivity
from
6
Volts
to
0,2
Volts.
Allow you to select the
2CH , 4CH
or
5CH mode.
Input- RCA Inputs
Full range line input to connect with
the head unit RCA Outputs.
'---
L...
r
....
!R
_JB._
~!LL
CROSSOVER
-
FRO•
T
CH.
LE EL
CROS'
OVER
-
RE~
CH.
LEVEL
000
HIGH
FULL
HIGH
PASS FROI T
CH.
HIGH
PASS
FULL
LOW
PASS
RO H.
c=J
~
~
Ci
-(Q
□
Sd'Hz
4kHz
soHz
160Hz
HIG
BAND
• •
6V
.2V
0 0
6V
.2V
PC
WER
250Hz
4kHz
000
~
~
~
6
-0
I I
Rl
50Hz
l
50Hz
ode 1
2:de
6V
.2V
A U
LT
2
4
5
rR
LOW
PASS
45Hz
CH.5
CH.
CH.
CH.
REMOTE
SIGNAL
INPUT
CROSSOVER
BOOST
LEVEL
INPUT
SELECTOR
I
- -
C
)
V
C
)
::,-...
"
I
Remote
Connection
for
the provided bass
remote control. Allows to adjust the
Bass EQ
subwoofer from f.i. the driver's seat.
Continously variable Bass Boost
Power-LED
from 0dB up to +12dB.
If
the green LED is illuminated,
the amp is in operation mode.
Protect-
LED
X-Over
CH1/2
&
CH3/4
If
the red LED is illuminated:
Selects the operation modes
of
the amplifier which is required:
a) Overheated
Position HPF:
b) Speaker wires shorted
Highpass/Subsonic (frequency response is limited downwards.
II
is
c) Overload (Impedance, less Power Supply)
controlled by the HP PASS-controller)
d) Amplifier is damaged
Position FULL:
The built-in electronic diagnostic protection saves the
Provides a full range signal to the speakers (whole frequency response).
amplifier and speakers from serious damage.
If
the red LED
lights up due to overheating, let the amplifier coold down a
while a turn it on again.
If
the red light is still lighting up, ensure that all connections,
especially the speakers are correct and not shorted.
If
the amp is still
in
protection mode, try to restart the
amplifier without any speaker or RCA wires.
If
the green light is
now
lighting up, re-check again all
speaker- and RCA-connections, to ensure correct
connection.
!ipeaker
&
RCA
Connections
RS5.4500D
INTERCONNECTION EXAMPLE 5-Channel Mode: 2x Stereo System (Front or rear)+1xSubwoofer
RCA
& Speaker wiring:
• Connect the RCA lineouts
of
the headunit with the RCA jacks LINE INPUT
of
the amplifier with appropriate high-value RCA cables.
• Connect the front
or
rear speakers with the speaker outputs
(Ch1
+/- and CH2 +/- SPEAKER), (CH3 +/- and CH4 +/- SPEAKER)
and (CH5 +/- SPEAKER) by using appropriate wires.
• Ensure by any means, that the total impedance load
of
all speakers is not lower than 2 ohms. Too low impedance cause high temperature
and will shut down the amplifier operation.
• Always ensure the correct polarity
of
the speakers. The interchange
of
plus and minus cause total loss
of
bass playback and could
damage the speakers
Caution!
Do not connect speaker(-) to the ground or vehicle's chassis.
Speakers
CH1
Speakers CH2 Speakers
CHS
2 - 8
Ohm
2 - 8
Ohm
2 - 8 Ohm
Bass Remote Control - connection
for
remote control.
This contoller regulates the Bass Level from e.g. the driver's seat.
=
+
SUB-
n
1~;
K
~I
OUTPUT
Speakers CH3 Speakers CH4
2 - 8
Ohm
2 - 8 Ohm
.0..
Connect RCA outputs
from head-unit with RCA inputs
(LINE INPUT CH1/2,CH3/4 & CH5).
•
By
using
bigger
speakers
(more
than
20cm)
you
can
set
the
X-OVER
switch
to
the
FULL
position (Full
Range
Signal).
•
By
using
smaller
speakers
(8.7cm
-
16cm)
you
must
set
the
X-OVER
switch
to
the
HPF
Position
(Highpass
Mode)
to
avoid
any
damage
by
lower
frequencies
on
the
speakers.
The
cut-
off
frequency
is
adjustable
with
the
HIGH
PASS
controller
and
should
be
set
between
10Hz
to
150Hz(CH1/2)
and
10Hz
to
150Hz(CH3/4),
depending
on
the
size
of
the
speakers.
•
The
LOW
PASS
Controller
is
not
in
use
in this
interconnecting
example.
LEVEL CONTROLLER
• Turn
the
LEVEL
controller
of
the
amplifier
to
the
6V
position.
• Turn
the
volume
controller
of
the
head
unit
to
80
-
90%
of
its full setting,
• Turn
the
LEVEL
controller
clockwise
until
you
hear
some
distortion.
•
Then
turn
back
the
LEVEL
controller
slightly until
you
hear
a
cleaner
sound.
BASS BOOST CONTROLLER
•
The
BASS
BOOST
controller
must
be
turned
to
0
dB
position in
this
interconnecting
example
.
15 16