Owner's Manual
!ipeaker
&
RCA
Connections
RS1
.8000D
RCA & Speaker wiring:
• Connect the LINE INPUT
of
the amplifier to the head unit line output with appropriate good quality RCA cables. As optional
feature the Balanced Inputs can
be
used. But therefor an signal transmitter with specific wires is required. Ask your specialist
dealer for the required equipment.
"i
Connect the subwoofer with appropriate wires to the terminal block (SPEAKER
OUTPUT+
and -)
of
the amplifier. As optional
feature a additonal Subwoofer can
be
connected to the non-occupied terminals.
• The minimum final subwoofer impedance must not
be
lower than 1 Ohms in total.
Too
low speaker loads result
in
too high heat
dissipation and may cause the amplifier run into protection.
• Please observe correct speaker channels and polarity as printed by the speaker terminal
=
t=
<=1
0
SPE
KERO
PUT
Caution!
Do
not connect speaker(-) to the ground or vehicle's chassis.
Bass Remote Control - Connection for remote control.
This Contoller regulates the Bass Level from f.i. the driver's seat.
=
+12V
REM
GND
" '
@
@ I
@
I
@
l @
@
~
Q Q
MIN MAX
l0Hz
50Hz 40Hz 150Hz O"
1110"
□
POWER
INPUT
By using a additional Subwoofe ,
~---"
connected to the non-occupied
Connect RCA outputs (SUB OUT)
of
L
r
c=
terminals, ensure that the total
the head unit with LINE INPUT
of
the amplifier.
Low Pass
impedance load
is
not lower
than 1 Ohm.
Subwoofer
1 - 8 Ohm
• This eliminates the higher frequencies. Set the crossover-frequency between 30Hz-250Hz, depending on the size
of
the
installed subwoofer.
Sub Sonic
• This eliminates the lowest frequencies and protects the speakers from damage. Set the frequency between 20Hz-50Hz,
depending on the size
of
the installed subwoofer.
Phase
• This Controller allows to adjust the Phase Shift 0° to 180° , to match the subwoofer to the vehicle's acoustic enviroment.
Input Level
• Turn the LEVEL control
of
the amplifier to 6V position.
• Turn the head unit volume control to about 80 - 90%
of
its full setting.
• Turn the LEVEL control clockwise until you hear some distortion.
• Then turn back the LEVEL control slightly until you can hear a clean sound.
Bass EQ
• This Controller regulates the Bass Boost from 0-
12
dB.
Caution! Please use the Bass-EQ carefully. The additional boost may result
in
clipping or overload.
Bass Remote
• The provided Bass Remote regulates the Bass Level from f.i. the driver's seat.
!ipeaker
&
RCA
Connections
RS1
.8000D
MASTER/
SLAVE-MODE/
Subwoofer-Mode with two Ampifiers
• Connect the "LINE IN" (L & R)
of
the MASTER-amplifier to the head unit's line output with appropriate good quality RCA cables.
• Connect the "SLAVE OUT" RCA Output
of
the MASTER-Amp with the "LINE IN" RCA Input
of
the SLAVE-AMP.
• Connect the "REMOTE"-Terminal
of
the MASTER-Amp with the supplied BASS REMOTE.
• Connect the "REMOTE"-Wire
of
your head unit with the REM-Terminals
of
both Amplifiers.
• Connect the subwoofer with appropriate wires to the terminal block (SPEAKER
OUTPUT+
and - )
of
both amplifiers. As optional feature an
additonal Subwoofer can be connected to the non-occupied terminals.
• Connect the Protect/Bridge Connection
of
the Master with the Protect/Bridge Connection
of
the Slave.
This connection warrants
if
there is an operation fault both amps, Master and Slave, would go into protection mode so the amps are prevented
for
any possible damages.
• The minimum final subwoofer impedance must not be lower than 2 Ohms in total
(1
Ohm for each Amplifier)
or
2 Ohms bridged.
Too
low speaker
loads result in too high heat dissipation and may cause the amplifier run into protection.
• Please observe correct speaker channels and polarity as printed by the speaker terminal.
MASTER
=
+ +
Caution!
Do
not connect speaker(-) to the ground or vehicle's chassis.
Bass Remote Control - connection
for
remote control.
This
contoller
regulates the bass level from e.g. the
driver's
seat.
MASTER
=
nm
~ o
0 ~
POWER
INPUT
L
=
~
~ ~ ~
□
RE
OTE
0. 0. 0.i;:::l
MIN MAX 10Hz 50Hz 40Hz 150Hz o
0
180°
n
=
+12V
REM
GND
Q
rn
J:
{;1:1
~
Connect
Master'
s Protect/Bridge
with
Slave
's
Protect/Bridge
Subwoofer
s
= =
00
R Q •; c O
CJ
□
'"'""
0 MIN MAX lOHz 50Hz 40Hz 150Hz O"
110"
L
00
L
C==:)
■
Subwoofer with Dual-Voice-Coil
2-8
Ohm
2 Subwoofers with Single-Voice-Coil
MASTER SLAVE MASTER SLAVE
Subwoofer with Single-Voice-Coil 1 - 8 Ohms
Subwoofer with Dual-Voice-Coil 1 - 8 Ohms per Voice-Coil
Caution: Please observe the right polarity. Slave's - to
Loudspeaker's+
and
Slave's+
to
Loudspeaker's-.
13
14