Owner's Manual
!ipeaker
&
RCA
Connections
RS1
.5000D
MASTER/
SLAVE-MODE/
Subwoofer-Mode
with
two
Ampifiers
• Connect the "LINE IN" (L &
R)
of
the MASTER-amplifier to the head unit's line output with appropriate good quality RCA cables.
• Connect the "SLAVE OUT" RCA Output
of
the MASTER-Amp with the "LINE IN" RCA Input
of
the SLAVE-AMP.
• Connect the "REMOTE"-Terminal
of
the MASTER-Amp with the supplied BASS REMOTE.
• Connect the "REMOTE"-Wire
of
your head unit with the REM-Terminals
of
both Amplifiers.
• Connect the subwoofer with appropriate wires to the terminal block (SPEAKER
OUTPUT+
and - )
of
both amplifiers. As optional feature an
additonal Subwoofer can be connected to the non-occupied terminals.
• Connect the ProtecUBridge Connection
of
the Master with the Protect/Bridge Connection
of
the Slave.
This connection warrants
if
there is an operation fault both amps, Master and Slave, would go into protection mode so the amps are prevented
for any possible damages.
• The minimum final subwoofer impedance must not be lower than 2 Ohms in total
(1
Ohm for each Amplifier)
or
2 Ohms bridged. Too low speaker
loads result
in
too high heat dissipation and may cause the amplifier run into protection.
• Please observe correct speaker channels and polarity as printed by the speaker terminal.
Caution!
Do
not connect speaker(-) to the ground or vehicle's chassis.
Bass Remote Control - connection
for
remote control.
This
contoller
regulates the bass level from e.g. the driver's seat.
MASTER
= =
+ +
(!CCI
O
[:
1: 1
na
0
S
KER
OUTP T
0
POWER
INPUT
SL
=
= =
nm
[!CC)
o
0
POWER
INPUT
Subwoofer with Dual-Voice-Coil
MASTER
SLAVE
C=::)
Connect Master' s Protect/Bridge
with Slave 's ProtecUBridge
Subwoofer
2 - 8 Ohm
Subwoofer with Dual-Voice-Coil 1 - 8 Ohms per Voice-Coil
0
0
R
0.
Wo.C
O
q
□
REMOTE
0 MIN MAX lOHz
SOHz
40Hz
15GHz
O"
1150"
,
00
,
■
2 Subwoofers with Single-Voice-Coil
MASTER
SLAVE
Subwoofer with Single-Voice-Coil 1 - 8 Ohms
Caution: Please observe the right polarity. Slave's - to
Loudspeaker's+
and
Slave's+
to
Loudspeaker's-.
Functions
&
Controls
RS1
.8000D
Low
Pass
This Controller adjusts the frequency response
of
your
subwoofer
upwards and is continously variable from
30Hz
to
250Hz
Sub
Sonic
This Controller eliminates the lowest frequencies to protect the
subwoofer
from damages. These
low
frequencies can cause damages.
The frequency is adjustable from 20 Hz to 50 Hz.
Level
This allows to adjust the input
Remote
-
sensitivity from
MIN
to
MAX
Connection
for
the provided bass remote
control. Allows to adjust the
subwoofer
from
Input-
RCA Inputs
f.i. the driver's seat.
Accepts line level(RCA)inputs
from 0.2 to 6 volts
/.
LINE OUT LIN
IN
LEVEL
SUBSONIC
LOW
PASS
PHASE
□
R
00
R
Q
0 0
CJ
0 u
POWER
FAULT
0
MIN MAX lOHz
SOHz
40Hz 150Hz
QO
180°
L
00
L
~1
rf
( )
/v
~
( )
,>
~
/,
Output-RCA
Outputs
Power-LED
Allows you to connect
additional amplifier
If the green LED is
illuminated, the amp is
in operation mode.
Phase
This Controller adjusts the Phase
Shift from 0° to 180°, to match the
subwoofer
to the vehicle's acoustic
enviroment.
Protect- LED
If the red LED is illuminated:
a) Overheated
b) Speaker wires shorted
c) Overload (Impedance, less Power Supply)
d)Amplifier
is damaged
The built-in electronic diagnostic protection saves the
amplifier and speakers from serious damage. If the
red
LED
lights up due to overheating, let the amplifier coold down a
while a turn it on again.
If the
red
light is still lighting up, ensure that all connections,
especially the speakers are correct and not shorted.
If the amp
is
still
in
protection mode, try to restart the
amplifier without any speaker or RCA wires.
If the green light
is
now lighting up, re-check again all
speaker- and RCA-connections, to ensure correct
connection.
11
12