X3.60 / X3.
INTRODUCTION 2 FEATURES & SPECIFICATIONS 3~4 CONTROLS & FUNCTIONS 5 ~ 10 PLANNING & MOUNTING YOUR SYSTEM 11 WIRING DIAGRAM 12 BRIDGING TWO AMPLIFIERS 13 ADJUSTING & TUNING 14 TROUBLE SHOOTING 15 TABLE OF CONTENTS TABLE OF CONTENTS
INTRODUCTION INTRODUCTION Amplifier's provide high-performance sound reinforcement for your mobile audio equipment. The Multi-Mode bridging capabilities allow flexibility in hosting several different speaker configurations. To achieve optimum performance, it is highly recommended that you read this Owners Manual before beginning installation.
FEATURES 4000Watts 350<@80Hz(+/- 5Hz) 15Hz ~150Hz 0.5 ~ 10.0 (volts) 24dB / octave 18dB 50Hz ~ 150Hz 0 ~ 180 deg. 0 ~ 18dB 11 ~ 16V DC 249 amperes DC * 21" x 11.5" x 2.5" 13.5V DC & 14.
FEATURES CONTROLS & FUNCTIONS X3.71 6500Watts 350<@80Hz(+/- 5Hz) 15Hz ~150Hz 0.5 ~ 10.0 (volts) 24dB / octave 18dB 50Hz ~ 150Hz 0 ~ 180 deg. 0 ~ 18dB 11 ~ 16V DC 510 amperes DC * 23.75" x 11.5" x 2.5" 13.5V DC & 14.
CONTROLS & FUNCTIONS Controls & Functions X3.
X3.
CONTROLS & FUNCTIONS Controls & Functions 1.Low Level OUT RCA jacks LINE OUT LINE IN LINE OUT LINE IN R L R X3.71 X3.60 L The LINE OUT allows you to build multiple amplifier systems without having to use splitter cords to distribute the signal. Now it is simply a matter of bringing one set of RCAS into the first amplifier, then using the line out RCA jacks as the feed to the next amplifier. 2. Low Level Input RCA jacks LINE OUT LINE IN LINE OUT LINE IN R L R X3.71 L X3.
Controls & Functions SUB SONIC 15Hz 40Hz Variable Subsonic Filter (15Hz - 40Hz) : The Subsonic filter will roll off all of the unwanted frequencies below 15Hz - 40Hz. This will allow the amplifier to use that wasted power on the audible bandwidth. 5. Bass Boost Control BASS BOOST 0 +18dB By using the bass boost function, bass notes at 45Hz are emphasized as much as 18dB. X3.71 8 X3.60 CONTROLS & FUNCTIONS 4.
CONTROLS & FUNCTIONS Controls & Functions 7. Low Level Filter Control LOW PASS 50Hz 150Hz This control is used to set the desired low pass frequency (50 ~ 150HZ). The filter acts to cut-off frequencies above the set-point. In general, the selected frequency should closely match the resonant frequency of the speaker box. 8.
10. LED indicatior POWER PROTECTION POWER : This GREEN LED will illuminate when the amplifier is turned "ON". If it fails to illuminate, check the power connections to the Amplifier and fuses. PROTECT: The amplifier protection circuitry will disable the amplifier if input overload, short circuit or extremely high temperature conditions are detected.
CONTROLS & FUNCTIONS Controls & Functions 12.B-Terminal (Chassis ground) X3.71 X3.60D To avoid unwanted ignition noise caused by ground loops, it is essential that the Amplifier be grounded to a clean, bare, metal surface of the vehicles chassis. Note : GROUND WIRE SHOULD NOT BE EXTENDED MORE THAN 3 FT (1 METER). 13. Remote Power On X3.71 X3.60D To remote wire From car stereo.
The mounting position of your Amplifier will have a great effect on its ability to dissipate the heat generated during normal operation. Under normal conditions, the heatsink will dissipate sufficient heat to avoid thermal shutdown. However please do not install the amplifier in a wooden box or similar device as this will prevent heat dissipation into the atmosphere. Temperatures in car trunks have been measured as high as (155'F) in the summer time.
WIRING DIAGRAM Wiring Diagram X3.60 SUB WOOFER 1 OHM X3.
Bridging Two Amplifiers SLAVE BRIDGING TWO AMPLIFIERS X3.
BRIDGING TWO AMPLIFIERS Bridging Two Amplifiers X3.
The amplifier automatically turns on a few seconds after you turn your vehicle's ignition switch to ACC or ON or turn on your auto sound system, depending on how you wired the system. The POWER indicator on the top of the amplifier lights when the amplifier is on. Important : Your amplifier requires 30 amps or more of power from your vehicle's battery during operation. To protect your battery from discharging, do not operate the amplifier unless your vehicle is running.
TROUBLE SHOOTING Trouble Shooting SYMPTOMS NO SOUND AMP NOT SWITCHING ON NO SOUND IN ONE CHANNEL CHECK Is the power LED illuminated? (NO) Check all fuses to amplifier. Be sure Turn-on lead is connected Check signal leads. Check gain control. Check Tuner/Deck volume level. Clean contacts on fuse holders. Is the Diagnostic LED illuminated? (YES) Check for speaker short or amplifier overheating. No power to power wire Repair power wire or connections.
