T E C H N O L O G I E S Owner’s Manual and Installation Guide LW1.1100D LW1.1700D LW1.
CONGRATULATIONS! You now own a Limited Edition LIL’WONDER Amplifier, the product of an uncompromising design and engineering philosophy. To maximize the performance of your system, we recommend that you thoroughly acquaint yourself with its capabilities and features. Please retain this manual and you sales receipt for future reference. Soundstream amplifiers are the result of American innovation and the highest quality control standards.
FEATURES Mono-Block Class D Amplifier Total Harmonic Distortion:0.
SPECIFICATIONS >105dB 15Hz-150Hz 0.50% 50Hz -150Hz,12dB 11-16 Volts DC Signal/Noise Ratio Frequency Response THD LPF Input Voltage Range High Impedance RCA/LINE Level Input Impedance 30K Ohms POWER RATINGS & FUSE MODEL 4 ohm 2 ohm 1 ohm FUSE LW1.1100D 600W 900W 1100W 35A X 3 LW1.1700D 700W 1200W 1700W 40A X 4 LW1.2600D 1000W 1800W 2600W 250A DIMENSIONS MODEL Length Width Height LW1.1100D 390mm 205mm 60mm LW1.1700D 450mm 205mm 60mm LW1.
TOOLS/PARTS FOR INSTALLATION NOTE: TOOLS ARE NOT SUPPLIED Small flat blade screwdriver phillips screwdriver (#2 or medium sized), Wire cutters, Wire strippers, - #6 round head screws, and 1 - #8 sheet metal screw (or nut, bolt flat washer, start washer) (see detail) 2 Ring connectors (large enough to accommodate your method of grounding) In-line fuse or Grommets (Sized to work with the power wire you plan to use in your installation) Tube of silicone seal.
Electrical Wiring All LIL’WONDER Amplifiers are equipped with easy top access screw terminals . These terminals are nickel-plated in order to ensure excellent electrical contact and to resist corrosion. When making electrical connections to the amplifier, please observe the following : Use at least 4 gauge or heavier wire for power and ground connections. Wire the amplifier directly to the car battery.
PANEL LAYOUT LW1.1100D LEFT VIEW L Line Out Line Input L Subsonic Filter Input Level Min Max 10Hz Low Pass Filter 40Hz 50Hz .1V-2V R 0 Bridged Mode Input Sensitivity R 150Hz Bass Boost 2V-8V +18dB PHASE 0 REMOTE CONTROL DATALINK Master PROTECTION 180 Slave RIGHT VIEW BATT+ SPEAKER REMOTE GND POWER CONNECTIONS FUSES LW1.1700D LEFT VIEW L Line Out Line Input L Subsonic Filter Input Level Min Max 10Hz Low Pass Filter 40Hz 50Hz Input Sensitivity R R .
PANEL LAYOUT LW1.2600D LEFT VIEW L Line Out Line Input Subsonic Filter Input Level L Min Max 10Hz Low Pass Filter 40Hz 50Hz .1V-2V R 150Hz 0 Bridged Mode Input Sensitivity R Bass Boost 2V-8V +18dB PHASE 0 REMOTE CONTROL DATALINK Master PROTECTION 180 Slave RIGHT VIEW SPEAKER POWER CONNECTIONS Class D Monoblock Amplifier Installation Wiring LW1.1100D/LW1.1700D/LW1.
Class D Monoblock Amplifier Installation Wiring LW1.1100D/LW1.1700D BATT+ SPEAKER FUSES REMOTE GND POWER CONNECTIONS LW1.1700D has four fuses here BATT+ SPEAKER FUSES LW1.
Class D Monoblock Amplifier Installation Wiring LW1.
Bridging Two LW1.1100D/LW1.1700D/LW1.2600D Amplifiers L Line Out Line Input L L Subsonic Filter Input Level Min Max 10Hz Low Pass Filter 40Hz 50Hz R .1V-2V R 0 Bridged Mode Input Sensitivity R 150Hz Bass Boost 2V-8V +18dB PHASE 0 REMOTE CONTROL DATALINK Master PROTECTION 180 Slave Power min L Line Out Line Input L Subsonic Filter Input Level Min Max 10Hz Low Pass Filter 40Hz 50Hz Input Sensitivity R R .
Bridging Two LW1.1100D/LW1.1700D Amplifiers BATT+ SPEAKER REMOTE GND POWER CONNECTIONS FUSES LW1.
Bridging Two LW1.
TROUBLE SHOOTING NO SOUND Is the LED lit? NO YES Check Power and Remote turn-on wire for voltage. Make sure Ground wire is secure. STILL NO SOUND See your Authorize Sound Stream Dealer. SOUND IN ONE CHANNEL ONLY Reverse left and right speakers by unplugging the speaker connector. turning it over and plugging it back in.
Caution: Please do not plug in or unplug RCA Plugs to the amplifier inputs while the amplifier is turned on. Doing so is potentially harmful to the amplifier by allowing RF(radio frequencies) into the amplifier, causing instability, during the brief period while the RCA shield is not connected, and the hot is connected. Only plug in or unplug RCA plugs with the amplifier off as Standard practice with all audio equipment.
