foundation Dear customer, first of all thanks for purchasing a SOUNDSATION® product. Our mission is to satisfy all the possible needs of musical instrument and professional audio users offering a wide range of products using the latest technologies for a reasonable price. We hope you will be satisfied with this item and, if you want to collaborate, we are looking for a feedback from you about the operation of the product and for possible improvements to introduce in the next future. Go to our website www.
ma REE CAUTION Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. WARNING When using electrical products, basic safety precautions should always be followed, including the following: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
TALKING CARE OF YOUR DRUM 0 DO NOT ATTEMPT TO OPEN THE UNIT OR MAKE ANY CHANGE IN THE CIRCUITS OR PARTS OF THE UNIT.
CONTENTS TABLE INSTALLATION SOUND MODULE . CONTROL PANEL BOTTOM PANEL PLAY PAD . TURN ON THE POWER PLAYING PADS . MASTER VOLUME DRUM KIT KIT SELECT KIT EDIT CHANGE THE VOICE AND VOLUME OF THE PAD . EXIT FROM THE EDIT MODE . PATTERN .. PLAY THE PATTERN EXERCISE WITH THE PATTERN METRONOME RECORD RECORD STANDBY . RECORDING STOP AND SAVE ..
INSTALLATION HI-HAT Ach H Hat SOUND MODULE The drawing shows a complete drum kit after installation. Each drum pad, cymbal pad and Hi-Hat control pedal has its part number underneath the component name for your reference in installation. The part number is also printed on the part packing box. Power adapter and connection cables are not shown in the drawing.
INSTALLATION {Insert the cymbal rods and adjust their position {4 Rotate the L-Rods to proper positions, then tighten the wing nuts fm) 3 {B Move and =~ to proper locations {1:0pen the ams, adjust the position of ams and cross beam, then tighten the wing nuts 76 Move and rotate the cymbal ‘clamp to proper location, then tighten the wing nuts {install the left and right foot, adjust the height to java the feet firmly fixed onto the ground
INSTALLATION COMPONENTS INSTALLATION Hi-Hat Installation 1. Remove the wing nut, washer and felt pad 2. Put the Hi-Hat into the rod along with parts removed In step 1. Fasten the wing nut. 3.Adjust the angle and height of the rod before tightening the wing nut. Snare Installation 1. Insert the snare into the L-Rod, then tighten the wing nut. 2. Adjust the angle of the i L-Rod then tighten the wing nut in the clamp. Sound module Installation 1.
SOUND MODULE TEMPO MASTER VOLUME PATTERN | 1 VOICE VOLUME DRUM OFF 7 8 9 HI-HAT PEDAL FRONT PANEL (1) Display: The display is a 3-digital 7-Segment LED type showing Information such as Kit number, Voice number ete. . (2) CLICK Button: Metronome On/Off switch (3) TEMPO Button: Change the tempo of the metronome, it is also used for recording and Patter playing.
SOUND MODULE USB TRIGGER HEADPHONE LINE OUT LINE IN BACK PANEL {1} Power Switch: Tum On/Off the sound module Note: After you tum the power off, do not tum it on immediately. Wait at least five seconds so that the electronic circuits can be properly reset. {2} Power In Jack: Plug in the DC cable of the attached adapter (3) USB Jack: The USE connector allows you to connect the drum directly to your computer's USB port. The USB interface Is compatible with Windows Atavist, Windows 7 and MAC.
PLAYING PADS Playing Snare Drum Strike the central position (head) of the pad te make (1) Tum down the textual audio device connected head sound, strike the rim of the pad to make a im with the drum. (2) Press the POWER button while don't strike pad or press the Hi-Hat control pedal. (3) Tum on external devices connected. (4) Strike the pad and adjust the volume to a proper level. All pads have striking force sensitivity feature.
DRUM KITS This drum has 20 preset drum kits for your choice. The kit is a combination of different instrument voices assigned to each pad which has unitary style for performance. Any kit could be edited and saved. After the power is tuned on, the kit mode is engaged automatically the KIT button is lit and the kit number is Shawn on the display. In other operation modes, you could press the KIT button to enter the kit mods directly.
DRUM The following procedure Is for vole assignment. The way of changing its volume is the same. While the VOICE button and the selected pad button blink, its current voice number will appear on the display. Use the +, button to change the vole number ranging 1 184. Press both + and button simultaneously, its original voice will be restored. All assignable voices are listed in the Appendix VOICE LIST. You can test the voice by striking the pad or pressing the pad button.
PATTERNS There are 50 built-in patterns for your enjoyment and exercise. PLAY THE PATTERN Press the PATTERN button to engage the pattern mode and its indicator will light up. The patter number with “P” in front will appear and blink on the display. Use the + or — button to select a patter. Press the PLAY button to start playing and the display will show measure number. Pad select buttons will flash to indicate which pad is performed.
METRONOME : N Ts Activate the metronome Press the CLICK button to activate the metronome, Its Indicator will light up and flash according to current tempo. = Note: During the pattern playing, the metronome cannot sound but the CLICK button will flash if the metronome is engaged. Press the button again to stop It. The speed of the metronome Is determined by tempo value. It is adjustable. Press the TEMPO button. Its indicator will light up and blink. The current tempo will appear on the display and blink.
RECORD This drum provides facilities to record one pace of your performance and save it as patter 51. The recording could be accompanied with pattern. Before recording, you should prepare necessary settings including selecting drum kit, metronome and tempo setting, pattern selecting etc. Press the RECORD button fo enter the record mode. The button will light up and blink to indicate the recorder is standby. The PATTERN button will light up automatically so that you can record your performance with a patter.
RECORD Press the RECORD button again or press the STOP button to terminate the recording. The RECORD button blinks and = is ready for the next recording. The new recording over-writes (eo) 8 the contents of the previous recording in unit of measure. In this way, you can edit your recording. fi Tip: The Auto Start mods Is recommended for overwrite and record with the patter. The metronome sound is for reference only. It is not recorded.
usB & MIDI MIDI stands for Musical Instrument Digital Interface. This is a world wide standard communication interface that enables electronic musical instruments and computers to communicate with each other se that instructions and other data can pass between them. This exchange of information makes it possible to create a system of MIDI instruments and devices that offers far greater versatility and control than that is available with isolated instruments.
VOICE LIST No. Description No. Description No.
VOICE LIST No. Description No. Description No.
SPECIFICATIONS Configuration 3X 8" Tom (without rim), 8° Snare (with rim feature), 12” Crash cymbal (with choke feature), 12" Ride cymbal, 8” HI-Hat, 6” Kick, Hi-Hat pedal Voice 184 Drum Kit 20 preset kits Pattern 50, Full and Mute drum mode Pad Button play drum sound with led blink Pad Edit Voice, Volume, Tempo default 120; range 40 ~240 Metro On/Off Record 1 editable song in overwrite mode Easy Reset holding button+ and button when power en Display 3x7LED Power gelcap Aux.
WARRANTY & SERVICE All SATIATION products feature a limited two-year warranty. This two-year warranty is specific to the date of purchase as shown on your purchase receipt.
WARNING PLEASE READ CAREFULLY EU and EEA (Norway, Iceland and Liechtenstein) only This symbol indicates that this product is not to be disposed of with your household waste, according to the WERE Directive ( 2202/96/EC) and your national law. This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (WERE) .
