SM-CMD2020 DVD/MP3/CD RECEIVER Instruction manual DVD/MP3/CD
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents.....................................................................................................................................2 Important safeguards ...........................................................................................
Important safeguards · Using the device at temperature below -10º may cause the breakage of the device. BEFORE USING PLEASE HEAT UP THE PASSENGER COMPARTMENT TO THE RECOMMENDED TEMPERATURE! · Read carefully through this manual to familiarize yourself with this high-quality sound system. · Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. · When replacing the fuse, be sure to use one with an identical amperage rating.
Installation/Connections First complete the electrical connections, and then check them for correctness. If you are not confident working with electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or other components of your vehicle, please call your dealer in order to have the unit professionally installed. Before the installation IMPORTANT: Remove two screws before installation. Otherwise, the DVD Player will not work.
3. Insert trim plate. When you prepare to insert trim plate, please check it s direction. Once it was up side down, it cannot be fixed. NOTE: Outer trim frame, hook, and mounting sleeve are not used for this installation. This is only intended as a general guide; contact the vehicle's manufacturer for specific instructions. This method of installation uses the screw holes at the sides of the unit and the holes of the existing vehicle mounting bracket. 1. Remove the hooks on both sides. 2.
Using the ISO Connector 1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated. Location 1 2 3 4 5 6 7 8 2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit. Cut the connector, connect the colored leads of the power cord to the car battery as shown in the colour code table below for speaker and power cable connections.
Panel controls Front panel 1. VOLUME-UP/DOWN, PUSH SEL MENU 2. LOADER 3. LCD (LIQUID CRYSTAL DISPLAY). 4. POWER BUTTON. Press more than 2 seconds to power off. 5. IR SENSOR 6. AUX input 7. TUNING UP/DOWN, PUSH MOD 8. BAND/NP BUTTON. Press it repeatedly to select your desired radio band during RADIO mode. 9. PRESET STATION [1-6] AND RPT, RDM BUTTONS. 1.Display OSD menu 2.Disc playback: Track repeat play. 3.Disc playback: Intro play (10 seconds). 4.Disc playback: Track random play. 5.Disc playback: Stop 6.
10. CLOCK BUTTON 11. APS/SUB BUTTON 12. EJECT BUTTON 13. EQ/LOUDNESS 14. MUTE BUTTON Press in 1 second to MUTE ON, press it again 1 second to MUTE OFF 15. FM STEREO/MONO Back of the front panel Press the button to open the panel. Disc slot: insert a disc for playback here Panel status indicator Reset hole Note: Pressing the RESET hole will erase the clock setting and stored stations. Panel status indicator lights up when you slide the panel down; flashes when you remove the panel.
ISO connector PLEASE USE ONLY ORIGINAL CONNECTOR WHICH GOES WITH SET. Note: ·In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the distortion during high volume level.
Remote control 1. MODE button 2. Power on/off 3. UP button 4. BAND/SYS button 5. ENTER button 6. LEFT button 7. STOP button 8. ST/PROGRAM button 9. AMS/RPT button 10. SEEK - / PREVIOUS button 11. LOC/RDM button 12. OSD button 13. PBC/MENU button 14. Digit area 15. PLAY/PAUSE button 16. MUTE button 17. TITLE button 18. Select subtitle language 19. RIGHT button 20. Setup button 21. ANGLE button 22. SLOW button 23. VOLUME button 24. ZOOM button 25. SELECT button (to select basic sound setting options) 26.
Battery information of remote controller 1. Press the catch and at the same time pull out the battery tray. 2. Insert the 1 x lithium battery, type CR 2025 3V battery with the stamped (+) mark facing upward. Insert the battery tray into the remote control. WARNING: Store the battery where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. Do not recharge, short, disassemble or heat the battery or dispose it in a fire.
Glossary PBC (PlayBack Control) PlayBack Control is a menu recorded on the disc with SVCD or VCD2.0 format. For the discs contained PBC, it can playback interactive software with the menu displayed on TV. And if the disc contains still images, it can playback high definition of still image. Title The title is the important part of DVD disc. The memory volume of the disc is rather big, that makes possible to record several films on one disc.
Features Fully compatible Fully compatible with the most popular discs formats such as DVD, CD, CD-R (containing MP3, JPEG), CD-RW represented in the market. Upgrade intelligently Support the function of upgrading the software for playing discs of new formats to keep up with the market competition. Strong output function The player has an analogue audio output of 2 channels, digital audio output and video output of complex video.
Compatible discs DVD Video DVD disc include video and audio data. The data can contained by the 12 cm diameter of DVD disc is 7 times of one can contained by the common CD-R disc. Its maximum continuous playback time can be up to 2 hours (one of double-sided disc can be up to 4 hours). DVD disc sort as 4 kinds of ones: single-layer and double-layers and single-sided, single layer and double-sided, double-layers and double-sided disc. SVCD Super VCD disc adopt MPEG-II compression way.
CD-R/CD-RW Compatible with CD-R/CD-RW disc with ISO9660 specification include the format of MP3, JPG, JPEG, Ac3, PCM, MP4, MPEG. DVD+/-R Compatible with DVD+/-R disc with UDF specification include the format of MP3, JPG, JPEG, Ac3, PCM, MP4, MPEG4, DivX (3.11/4.0/5.0/6.XX). Note: Support of MPEG4 Standard: playback of digital video compressed in DivX 3.11, DivX 4.0, DivX5.0, DivX 6.XX.
General operation Power button Press POWER button on the front panel or any other button on the panel except EJECT to turn on the unit. Press POWER to switch the set to POWER OFF. When you switch off the system or car ignition, the settings, tuner presets and the volume level will be retained in the unit s memory. Mode Selection Press the MODE Button to cycle the Play Mode between RADIO and DISC PLAY. Press and hold the MODE button to activate the AUX mode.
Adjusting clock Setting the clock time 1. Press and hold CLK for more than 3 seconds to select the hour setting. Hour digits will blink. 2. Rotate the control to set the hours. 3. Press VOL knob to select the minute setting. Minute digits will blink. 4. Rotate the control to set the minutes. 5. Press CLK Button, or leave the unit idel. Time setting is now confirmed. Reset Press EJECT to open the panel and press the RESET hole to restore the unit to the original factory settings.
Digital tuner Choose Radio Band Press the MODE Button to access the radio function. The unit comes with five bands- three FM Bands (FM1, FM2, and FM3) and two AM Bands (MW1, and MW2). Each of the five bands can store up to six preset stations, for a total of 30 preset memory stations. Radio Tune / Seek Function In Radio Mode, press right tuning knob (Seek +/- Button) to manually adjust the radio frequency. Turn it clockwise for manual seek +, and anti-clockwise for manual seek -.
Automatic Store/Preset Scan A. Automatic Scan & Store While listening to the FM Radio, press and hold the APS Button for 3 seconds. The receiver will automatically scan and save stations for all the 3 FM Bands, whichever band (FM1, 2 or 3) you are listening to. While listening to the AM Radio, press and the APS Button for 3 seconds. The receiver will automatically scan and save stations for the 2 AM Bands, whichever band (MW1 or 2) you are listening to. B.
DVD/VCD/CD/MP3/CD-R Discs for playback · This set can play all digital audio CD, HDCD, CD-R/RW, MP3,WMA, VCD, SVCD, DVD, DVD-ROM. · The following file types are supported: Audio files: MP3 (*.mp3) WMA (*.wma) Video files: MP4 (*.avi, DIVX3.11/4.0/5.0/6.XX and XVID) MPEG 2(*.vob) MPEG 1(*.dat) Picture file: JPEG (*.jpg) · ISO 9660 or ISO 9660 +Joliet format - Max. 30 characters · Max. Track number is 448 · Max. nested directory is 8 levels · The max. album number is 99 · The max.
OSD (Display information) Press the OSD button (by pressing and holding button 1 on the front panel, or pressing the OSD button on the remote control) so that the OSD will be display on the monitor. Details such as title, track, playtime, etc, will be shown. Press again to turn the OSD off. Playing the DVD (without menu) After the disc is loaded, the movie of the DVD will be played automatically. The menu will be prompted so that you can choose the setting.
Button 2: Right + Repeat Press the No.2 Button to navigate the setup menu right-ward. Press and hold the button for 3 seconds for repeating the same track continuously. RPT" will appear on the display. Press and hold this button again to stop repeating. Button 3: Up + Scanning Tracks Press the No.3 Button to navigate the setup menu up-ward. Press and hold the button for 3 seconds to play the first 10 seconds of each track. INT" will appear on the display. Press this button again to resume playback.
Subtitle Selection Press the Sub-T button on the remote control to choose the subtitle you want. The subtitle languages available differ from Disc to Disc. You can also use the setup menu to confirm. Refer to the packing of the Disc for details. Track Time Search Press the GOTO button on the remote control to search the desired track time to play the Disc. The OSD will be prompted. Make use of the navigation keys and digit keys on the remote control to choose your desired chapter, track or time.
Programme Mode Press the PROG button on the remote control to set the program play. Use the Navigation and Digit keys to set the Chapter and Track no. as your desired sequence. Press Enter to begin the program play. Press the PROG button and confirm a blank program again to cancel this operation. Electronic Shock Protection This unit is programmed with Electronic Shock Protection (ESP) so that the signal will be protected against rough roads: for DVD - 5 seconds.
Mixed-disc operation While you are playing mixed disc, which contains MP3, WMA, JPG or DIVX formats, just insert the disc into the CD slot and the menu on the right hand side will be promted. The unit will directly play the audio files. However, you can use the navigation and Enter keys to select the format that you would like to view/listen to. Audio mode Audio files will be played directly if they are presented in the mixed disc. Both MP3 and WMA file format are supported.
Button 1-6 The functions of button 1-6 also apply to the mixed-disc play. Back to the menu If you would like to go back to the playlist menu to choose the other file to view/listen to, press and hold button No.5 to stop the playback. Then the playlist menu will be prompted and you can select other files.
VCD/CD operation Insert/Eject CD Insert a disc into CD slot with label side up. The disc will be automatically loaded into the unit, even when it is off or at radio mode. The word LOAD will show on the display and the disc will play automatically. Press the EJECT Button to eject the disc from the slot. If the disc is not removed from the slot within 5 seconds, it will automatically be loaded into the slot again. When the disc is ejected and removed, the unit will automatically switch to radio mode.
VCD: Press AUDIO during playback. It is possible to switch the sound between mono and stereo sound. The sequence is as follows: Left Vocal --> Right Vocal --> Mono Left --> Mono Right --> Stereo CD: Press AUDIO during playback. It is possible to switch the sound between mono and stereo sound. The sequence is as follows: Mono Left --> Mono Right --> Stereo Title Playing For VCD2.0, press the PBC button on the remote controol while the disc is playing. You can switch between PCB on and PBC off mode.
AUX IN, RCA OUT, SUB OUT&Video OUT Auxiliary Input The Auxiliary Input Jack is on the rear of unit. Insert the RCA plugs into the AUX IN jack on the front of the unit. Route the other end of the RCA to the any external audio device such as walkman and discman. Press and hold the Mode button to choose AUX. Use the volume control to adjust volume. RCA Output The RCA Output Jack is on the back of the unit.
Menu operation Press SETUP button on the remote control to display setup screen, use buttons to select the desired item: System, Language, Audio, Video, Digital. System setup TV system Select the TV system in the setting menu. Screen saver The screen saver appears if disc stop last more than 3 minutes. Original setting: On.
Video output mode Original setting: INTERLACE-YUV. Setting TV type Select TV type to watch wide screen movies. 4:3 Pan Scan: For 4:3 TV, left and right edges will be cut. 4:3 Letter Box: For 4:3 TV, black bars will appear on top and bottom. 16:9: For 16:9 wide screen TV. Setting password Original password is 0000. Setting rating The rating of the disc is from 1 to 8: (1) with the most limits when playing. (8) with the least limits when playing.
Note: The rating can be selected only under the password unlocked status, and the limits can be worked only under the password locked status. Load default If this item is selected, the unit will return to original setting. Language setup Setting the on-screen display language Select the language to be used for the on-screen display. Setting the audio language Select the language to be used for the audio. You can select a preferred audio from those included on the DVD video disk.
Setting the subtitle language Select the language to be used for the Subtitles. You can select a preferred subtitle from those included in the DVD Video disk. (The screen on your player may have difference with the screen shown here) Setting the menu language Select the language to be used for the Menu. You can select a preferred audio from those included on the DVD video disk. (The screen on your player may have difference with the screen shown here.
Setting volume Setup the volume with the buttons. Video setup Brightness Set the brightness of the video output with . Contrast Set the contrast of the video output with . Hue Set the hue of the video output with 35 .
Saturation Set the saturation of the video output with . Sharpness Set the sharpness of the video output with . Digital setup Output mode Select the output mode: LINE OUT: Compress the input signal. The volume is small. RF REMOD: The volume is large.
Dynamic range When you select the compressed mode as line out , select it to adjust the compression proportion and get the different compressed effect. When select FULL, the audio signal is minimum; when select OFF, the audio signal is maximum. Dual mono Select the audio channel from STEREO, MONO L, MONO R and MIX MONO.
Anti-theft system Removing the panel 1. 2. 3. 4. Press POWER button to switch off the power of the unit. Press EJECT button to flip down the panel. Hold the middle of the panel. Take off one end, and then take off the other end. Place the panel into the case and take it with you when you leave the car. Install the panel 1. Hold the panel and ensure the panel faces toward you , and set the right side of the panel in the panel bracket. 2. Press the right side of the panel until it locks. Remove the unit 1.
Handling discs · · · · · Dirty, scratched or warped discs may cause skip ping or noise. Handle the disc only by the edges. To keep clean do not touch its surface. Discs should be stored in their cases after use to avoid scratches. Do not expose discs to direct sunlight, high humidity, high temperature or dust. Prolonged exposure to extreme temperature can wrap the disc (such as leaving the discs in your car during summertime). · Do not stick or write anything on either side of disc.
Troubleshooting guide Symptom Cause Solution General No power The car ignition is not on. If the power supply is properly connected to the car accessory switch the ignition key to ACC . The fuse is blown. Replace the fuse. Disc Presence of disc inside the player. Remove the disc in the player then put a Disc cannot be loaded. new upward. Disc cannot be read. Inserting the disc in upside down. Insert the compact disc with the label facing Compact disc is extremely dirty or upward. defective.
Specification General. Power supply: Current consumption/Fuse: Maximum power output: Dimensions (W x H x D) Working temperature range: FM Stereo Radio. Frequency range: Usable sensitivity/ I.F. Frequency: MW Section. Frequency range: DVD Deck Specification Format Video System/ Audio System Loading System Mounting Angle 12V DC 8A/ 10A & 1A 50Wx4 channels 178 x 51 x 178 mm -20º - +60º 87.5 - 108.0 MHz 3 uV/ 10.
! . , , . ........................................................................................................................................ 42 ....................................................................................................................... 43 / ...................................................................................................................... 44 ................................................................................................................
· -10º ! · · · . · · , , · , , . , , . . , · , · · . , . , , . . , · , . , , . · . , . . , , , . . , . . · 43 . .
/ . , , , . : . 4,75 5,56 DVD , . . , . 1. . ). , ( 2. . . 3. . , , . 44 .
: , . , . , . 1. 2. . . . 3. 2 . , .
4 4 , . 4 , 8 . . 4 . 46 . .
ISO 1. ISO, , 2. . ISO , . , .
1. 2. 3. 4. , . POWER 2 5. 6. 7. 8. . AUX , (BAND/NP) RADIO. 9. 1.Display OSD menu 2.Disc playback: Track repeat play. 3.Disc playback: Intro play (10 seconds). 4.Disc playback: Track random play. 5.Disc playback: Stop 6.Disc playback: Set/Play/ Pause.
10. 11. 12. 13. 14. 15. (CLOCK) APS/SUB EJECT EQ/LOUDNESS ( MUTE 1 STEREO/MONO. ) , . : 49 .
ISO , . : · , , .
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29.
: 1. . 2. CR 2025 3 , + . . : 1. . , . 2. 3. , , . , . 4. , .
PBC ( ) , . , PBC, . . DVD, . 1, 2 . , , 3. . , . . . . , .
1. DVD, CD, CD-R ( MP3, JPEG), CD-RW, . 2. , . 3. , 2- , , . 4. icture CD, Photo CD icture CD Photo CD . 5. . (Screen Saver) (Screen Saver). , 5 Screen Saver. .
DVD Video DVD- . CD-R 4 ). DVD (Æ12 ) 7 . 2 DVD- : , 4 , ( , , . SVCD SVCD MPEG2. , VCD. . SVCD . VCD2.0 VCD1.1 VCD2.0 . ( VCD1.1 Picture CD , VCD2.0, ). , CD, VCD1.1 (Æ12 . ) 74 . DVCD DVCD. DVCD VCD . DVCD . CDDA CD-DA (Æ12 CD-DA. ) 74 CD-DA . . MP3/JPEG JPG . Picture-CD 3 CD-R/CD-RW/CD-ROM , MP3/JPG, Picture-CD , , 55 . Picture-CD Kodak.
Photo-CD Photo-CD , CD-R/CD-RW . Photo-CD Konica. , CD-R/CD-RW ISO9660, 3, JPG, JPEG, Ac3, PCM, MP4, MPEG. DVD+/-R DVD+/-R PCM, MP4, MPEG4, DivX (3.11/4.0/5.0/6.XX). : DivX5.0, DivX6.XX ( UDF, MPEG4: 3, JPG, JPEG, Ac3, , , ). 56 DivX 3.11, DivX 4.
POWER POWER, , EJECT, . , . . MODE MODE RADIO ( MODE ) DISC PLAY ( AUX. Vol VOL, VOLUME - BASS ( - TREBLE ( VOL/BAS/TRE/BAL/FAD, VOL. DSP , . ) . , DSP . ) BALANCE - . FADER - . MUT , , . 57 , ).
LOUD EQ/LUD, LOUD OFF. . . 1. 2. 3. 4. 5. LOUD ON CLK 3 . , , . . VOL, . , . . CLK , EJECT, . . RESET, . EQ/LUD CLASS : POP ROCK FLAT .
MODE MW2). AM (MW1 . 5 6 FM (FM1, FM2 30 . , (Seek +/-) FM3) . , . . FM ST ON , MON/ ST . , . , . LOC a. b. . LOC ON ; _DX_ . . 6 , . , . .
A. FM APS 3 FM M 3 . 3 . . APS 2 . B. APS . AMS FM APS FM AMS , , .
DVD/VCD/CD/MP3/CD-R · CD, HDCD, CD-R/RW, MP3,WMA, VCD, SVCD, DVD, DVD-ROM. · · · · · · · · · · : : MP3 (*.mp3) WMA (*.wma) : MP4 (*.avi, DIVX3.11/4.0/5.0/6.XX and XVID) MPEG 2(*.vob) MPEG 1(*.dat) : JPEG (*.jpg) ISO 9660 + Joliet 30 . 448. -8 . 99. - 99 59 . MP3 : 8 48 ( P3 : 32 - 320 ( : *.ACC, *.DLF, *.M3U, *.PLS, MP3 PRO, . ISO 9660 : EJECT, , . , : . . , . , . : ). ). . LOAD, EJECT, . 5 44,1 128 DRM. MP3, JPEG, . 61 .
( ) 1 OSD . . , . . DVD ( ) . LOC/MENU . PBC . PBC , . TITLE , . . . . . . . . , , . . 1: + OSD 1-6 . ) Setup ( . . 3 1 . .
2: 2 3 . RPT". . . Button 3: + 3 . 10 3 INT". . . 4: 4 . . 3 RDM . . 5: 5 . 3 . 5 . 6: SETUP + 6 . , , , , 1-5 , . 6 3 AUDIO . . . . MO/ST . , . .
Sub-T . , . . GOTO . . . ENTER , . +/ZOOM . 2 1/2 2 ( 5 ). SLOW 1/7. . Play/Pause. ANGLE . . : . , . , INVALID KEY . BND/NP : NTSC, PAL, PAL60, AUTO. , AUTO. ( 64 , ).
PROG . . . . PROG Enter . DVD 5 .
, MP3, WMA, JPG DIVX, . . , . . MP3 WMA. . , . Jpg . . , . jpg . . MP4, MPEG4 . (*.avi). , DivX 3.11 DivX . 6.XX. , . . . . . . . , , . .
1-6 1-6, , , . . , , 5 .
VCD/CD : EJECT, , . . . , LOAD, : EJECT, . 5 . . , , . , . : MP3, JPEG, . CD CD . . . . . . . . , , . . 1-6 1-6 (OSD, INTRO, REPEAT, RANDOM, STOP & PLAY/PAUSE) VCD/CD .
MO/ST AUDIO . , . . AUDIO VCD: . . : )--> ( AUDIO CD: )--> ( )--> ( )--> ( ) . . : )--> ( )--> ( ) VCD2.0 PBC . . . VCD 10 , , CD - 40 .
AUX, RCA, , AUX AUX . AUX IN. RCA Mode . RCA , CD , AUX. . RCA RCA ( RCA. ( , = . ). , , = ). . ( . ). , RCA. . . . , AUX. ( ) . ). ( , ) . . . 2 BAND/P/N , PAL 70 ( NTSC.
SETUP , , ENTER, : , . , , , . : 3 . : INTERLACE-YUV. 71 .
. 4:3 PS: 4:3 LB: 16:9: 4:3. 4:3, 16:9. . . 0000. 1 (1) (8) 8: . . :8 : , .
, . . . DVD ). .( . DVD ). .
. DVD .( ). . : SPDIF/ RAW: SPDIF/ PCM: . . . .
. . . .
. : LINE OUT: RF REMOD: . . . line out , , . Full , , .
: , , , 77 .
1. 2. 3. 4. POWER, EJECT, . . . , . , 1. , . . . 2. 1. 2. 3. . . , . 78 .
· · , ( ). , . · , . · , , . ( · , ). · . , , . · · , . , . . ( , ), , . ) . , , , . . ) , , . .
. , . . . . , . . . . . , . . . . . . RESET. . . . 30 . , 30 . . . . . . 80 . .
. : : ( ) : FM . : / 12 , 8A/ 10A & 1A 50 4 178 50 165 -20º - +60º 87.5 - 108.0 3 / 10.7 : MW DVD . . : 522-1620 DVD/SVCD/VCD/MP4/MP3/WMA/CD/HDCD/DVDAudio/MPEG4/DivX/Pi cture-CD/Photo-CD/CD-R/CD-RW/DVD±R/JPEG / NTSC/PAL / 24 /96 0 - +/-30 16:9 4:3 1.0 , 75 500 . 2 RMS (+/-3 20 20 60 /50 CD . 2000 (A-vtd)/ ) . .
