Data Sheet

ManualsBrandsSOS Electronic ManualsArduinoSOS Electronic ARDUINO_MC60GSM/GPS

Arduino MC60E GSM/GPRS/GNSS/BLE Shield Ver. 0.9

Arduino MC60(E) GSM/GPRS/GNSS/BLE Shield

The Arduino MC60(E) GSM/GPRS/GNSS/BLE Shield is a helpful tool for those advanced

hobbyists and professionals, who want to get familiar with GSM/GPRS/GNSS/BLE

data/voice communication using their Arduino board. With a powerful MC60(E) module

from Quectel users are able to use this shield in many different applications. Please read

the MC60(E) Hardware design and MC60 AT Command Set documentation first.

MC60E documentation download http://www.quectel.com/qdownload/mc60.html

1. Hardware Requirements:

− valid micro SIM card

− Arduino UNO (ATMega 328P), Mega (Atmega2560) or compatible board

2. Technical requirements

− Operating voltage range: 6-12VDC

− Operating current: up to 2A DC during transmission bursts, make sure your power

supply is sufficient for powering GSM module during these bursts

3. GSM/GPRS/GNSS/BLE module:

− MC60 QUECTEL documentation:

http://www.quectel.com/qdownload/mc60.html

− RF connector – SMA female, telematic antenna is part of delivery, any GSM

antenna with SMA connector can be used

Summary of content (5 pages)

PAGE 1
Arduino MC60E GSM/GPRS/GNSS/BLE Shield Ver. 0.9 Arduino MC60(E) GSM/GPRS/GNSS/BLE Shield The Arduino MC60(E) GSM/GPRS/GNSS/BLE Shield is a helpful tool for those advanced hobbyists and professionals, who want to get familiar with GSM/GPRS/GNSS/BLE data/voice communication using their Arduino board. With a powerful MC60(E) module from Quectel users are able to use this shield in many different applications. Please read the MC60(E) Hardware design and MC60 AT Command Set documentation first.
PAGE 2
4. Arduino MC60(E) Shield description − LEDs: Red LED – Network Light permanently OFF MC60 module is OFF 64 ms ON / 800 ms OFF MC60 is not logged in the network 64 ms ON / 2000 ms OFF MC60 is logged in the network 64 ms ON / 600 ms OFF Ongoing GPRS data transfer − Green LED: Shield Powered − Yellow LED: 1PPS (1 Pulse Per Second) 5.
PAGE 3
PIN2 D1_TX (MC60 Shield ---> Arduino) default PIN3 D2 (Alternative SW RX) PIN4 D3 (Alternative SW TX) PIN5 DETECT (uSD card presence detection) PIN6 RI (Ring Indicator) PIN7 No connection PIN8 ENABLE (Could be used to switch VREG input ON/OFF) Component placement and board overwiev: BOM list: Part Value Device Package Description ANT1 ANTENNA GSM ANTENNA GSM 2J0104 ANT2 ANTENNA GPS ANTENNA GPS 2J450GMP C1 100uF 25V CPOL-EUD PANASONIC_D C2 100nF CAP0402 C0402 C3 100uF CP
PAGE 4
C12 DNM C-EUC0402 C0402 CAPACITOR, European symbol C13 DNM C-EUC0402 C0402 CAPACITOR, European symbol C15 DNM C-EUC0402 C0402 CAPACITOR, European symbol C16 DNM C-EUC0402 C0402 CAPACITOR, European symbol C18 1uF CAP0402 C0402 Capacitor GPS LTI-SASF54GT LTI-SASF54GT LTI-SASF54GT SMA vertical PCB thrue hole jack GSM BU-SMA-H BU-SMA-H FEMALE SMA CONNECTOR IC1 MIC29302W MIC29302W BU-SMA-H DPAK171P1524X4856N J1 Power M06SIP 1X06 Header 6 J2 Analog M06SIP 1X06 Header
PAGE 5