Operating Instructions Sophos Access Points
Operating Instructions Foreword We are pleased to welcome you as a new Sophos Access Point customer. These operating instructions will help you install and configure the access point and provide technical specifications of all Sophos access point models.
Operating Instructions Connect the access point to the power supply The AAP 30, AP 50, AP 55, AP 55C, AP 100, AP 100C, and AP 100X can be powered directly through the Power-over-Ethernet-injector. Note that it is also possible to power them by a PoE-compliant switch. For more information on PoE-injectors, see below. Connect the AP 10 and AP 15 to the power supply. Please use the power supply from the scope of supply. Note that the AP 15 can also be operated through a PoE-injector or PoE-compliant switch.
Operating Instructions Accepting the access point The UTM appliance will start to communicate with the access point and they will show up as “Pending” on the Wireless Protection > Access Points tab in WebAdmin. The ID of the Access Points, shown in square brackets, is also printed on the bottom of the device. It can be used to distinguish the access point. By clicking the Accept button, you are given the option to select the channel this access point will transmit on.
Operating Instructions AP 10 Scope of supply Sophos AP 10 Security Notes Power supply Detachable dipole antenna Ethernet cable Mounting instructions The Sophos AP 10 can be mounted on the wall. Screws are not included in delivery. Only use screws whose dimensions correspond with the mounting holes on the back side.
Operating Instructions Technical specifications Sophos AP 10 Chassis Plastic housing, white Maximum throughput 150 Mbit/s LAN interfaces 1 x 10/100 Base-TX Supported WLAN standards 802.11 b/g/n 2.4 GHz Antenna 1 x detachable dipole antenna (2 dBi) Connector type: RP-SMA Frequencies / channels 2.412~2.462 GHz Channels 1-11 Power supply 100-240 VAC, 50/60 Hz, max. 0.3 A Power consumption 8 W (max.
Operating Instructions AP 15 Scope of supply Sophos AP 15 Security Notes Power supply 2 Detachable dipole antenna 2 screws and dowels Ethernet cable Important note: Sophos AP 15 requires Sophos UTM V 9.207 to be installed. Mounting instructions The Sophos AP 15 can be mounted on the wall. Screws are included in delivery.
Operating Instructions Technical specifications Sophos AP 15 Chassis Plastic housing, white Maximum throughput 300 Mbit/s LAN interfaces 1 x 10/100/1000 Base-TX Supported WLAN standards 802.11 b/g/n 2.4 GHz Antenna 2 x detachable dipole antenna (2 dBi) Connector type: RP-SMA Frequencies / channels ETSI FCC 2.412–2.472 GHz (Channels 1-13) 2.412-2.462 GHz (channels 1-11) Power supply 12 Vdc / 1 A Power consumption 2.5 W (max.) Power-over-Ethernet 802.
Operating Instructions AP 15 Mounting template 12 cm (4,72 in) Do not shrink to fit when printing Wireless Access Points 8
Operating Instructions AP 30 Scope of supply Power-over-Ethernet (PoE) injector + power cord Sophos AP 30 Security Notes 2 Detachable dipole antenna 2 screws and dowels Ethernet cable Mounting instructions The Sophos AP 30 can be mounted on the ceiling. Screws are included in delivery. Use the screws from the scope of supply or screws whose dimensions correspond with the mounting holes in the bracket. 1. Remove the bracket from the housing Unlock the bracket on the backside by turning it (approx.
Operating Instructions Technical specifications Sophos AP 30 Chassis Plastic housing, white (smoke detector design) Maximum throughput 300 Mbit/s LAN interfaces 1 x 10/100 Base-TX Supported WLAN standards 802.11 b/g/n 2.4 GHz Antennas 2 x directional internal antennas (4 dBi) Frequencies / channels 2.412~2.462 GHz Power supply 100-240 VAC, 50/60 Hz, max. 0.5 A Power consumption 8 W (max.) Power-over-Ethernet 802.
Operating Instructions AP 50 Scope of supply Sophos AP 50 Security Notes Power-over-Ethernet (PoE) 2 Detachable dipole antenna Ethernet cable injector + power cord Mounting instructions The Sophos AP 50 can be mounted on the wall. Screws are not included in delivery. Only use screws whose dimensions correspond with the mounting holes on the back side.
Operating Instructions Technical specifications Sophos AP 50 Chassis Plastic housing, white Maximum theoretical throughput 300 Mbit/s LAN interfaces 1 x 10/100/1000 Base-TX Supported WLAN standards 802.11 a/b/g/n 2.4 GHz / 5 GHz Antennas 2 x 2.4G/5G (3dBi/5dBi) dual-band antenna Frequencies / channels Radio I: 11b/g/n: 2.412-2.472 GHz (ETSI) Channels 1-11 2.412-2.462 (FCC) Channels 1-11 (FCC) Radio II: 11a/n: 5.180-5.240 GHz (ETSI / FCC) Channels 36, 40, 44, 48 (ETSI / FCC) 5.745-5.
Operating Instructions AP 50 Mounting template Wireless Access Points 16mm 2mm 17,05 cm (6,71 in) Do not shrink to fit when printing 5mm 13
Operating Instructions AP 55 Scope of supply Sophos AP 55 Security Notes 2 Detachable dipole antenna 4 screws, dowels and metal plates Ethernet cable Important note: Sophos AP 55 requires Sophos UTM V 9.308 to be installed. Mounting instructions The Sophos AP 55 can be mounted on the wall. A mounting kit is included in delivery.
Operating Instructions Technical specifications Sophos AP 55 Chassis Plastic housing, white Physical security Kensington lock Maximum theoretical throughput 867 Mbps (5GHz / 802.11ac) + 300 Mbps (2.4GHz / 802.11n) LAN interfaces 1 x 10/100/1000 Base-TX Supported WLAN standards 802.11a/b/g/n/ac Antenna 2 x detachable dipole antenna (2 dBi) Frequencies / channels ETSI 2.412–2.472 GHz (Channels 1-13) Connector type: RP-SMA RLAN sub-band 1: 5.180-5.320GHz (channels 36-64) RLAN sub-band 2: 5.
Operating Instructions AP 55C Scope of supply Sophos AP 55C Security Notes Mounting bracket Screws and T-rail clips Ethernet cable Important note: Sophos AP 55C requires Sophos UTM V 9.308 to be installed. Mounting instructions The Sophos AP 55C can be mounted on the ceiling. Screws are included in delivery. Use the screws from the scope of supply or screws whose dimensions correspond with the mounting holes in the bracket. 1.
Operating Instructions Technical specifications Sophos AP 55C Chassis Top enclosure: plastic, white; bottom enclosure: metal, white Physical security Kensington lock Maximum theoretical throughput 867 Mbps (5GHz / 802.11ac) + 300 Mbps (2.4GHz / 802.11n) LAN interfaces 1 x 10/100/1000 Base-TX Supported WLAN standards 802.11a/b/g/n/ac Antenna 4 x internal antennas Frequencies / channels ETSI 2.412–2.472 GHz (Channels 1-13) RLAN sub-band 1: 5.180-5.320GHz (channels 36-64) RLAN sub-band 2: 5.
Operating Instructions AP 100 Scope of supply Sophos AP 100 Security Notes 3 Detachable dipole antenna 4 screws, dowels and metal plates Ethernet cable Important note: Sophos AP 100 requires Sophos UTM V 9.207 to be installed. Mounting instructions The Sophos AP 100 can be mounted on the wall. A mounting kit is included in delivery.
Operating Instructions Technical specifications Sophos AP 100 Chassis Plastic housing, white Physical security Kensington lock Maximum theoretical throughput 1.3 Gbps (5GHz / 802.11ac) + 450 Mbps (2.4GHz / 802.11n) LAN interfaces 1 x 10/100/1000 Base-TX Supported WLAN standards 802.11a/b/g/n/ac Antenna 3 x detachable dipole antenna (2 dBi) Frequencies / channels ETSI 2.412–2.472 GHz (Channels 1-13) Connector type: RP-SMA RLAN sub-band 1: 5.180-5.320GHz (channels 36-64) RLAN sub-band 2: 5.
Operating Instructions AP 100C Scope of supply Sophos AP 100C Security Notes Mounting bracket Screws and T-rail clips Ethernet cable Important note: Sophos AP 100C requires Sophos UTM V 9.308 to be installed. Mounting instructions The Sophos AP 100C can be mounted on the ceiling. Screws are included in delivery. Use the screws from the scope of supply or screws whose dimensions correspond with the mounting holes in the bracket. 1.
Operating Instructions Technical specifications Sophos AP 100C Chassis Top enclosure: plastic, white; bottom enclosure: metal, white Physical security Kensington lock Maximum theoretical throughput 1.3 Gbps (5GHz / 802.11ac) + 450 Mbps (2.4GHz / 802.11n) LAN interfaces 1 x 10/100/1000 Base-TX Supported WLAN standards 802.11a/b/g/n/ac Antenna 6 x internal antennas Frequencies / channels ETSI 2.412–2.472 GHz (Channels 1-13) RLAN sub-band 1 5.180-5.320GHz (channels 36-64) RLAN sub-band 2: 5.
Operating Instructions AP 100X 4 wood screws and wood/gyprock plug, 2 metal straps 4 M6 screws and washers Sophos AP 100X Security Notes 6 antenna 1 wall mount plate Ethernet cable 1 M25 Grounding wire cable gland Installation Important note: Sophos AP 100X requires Sophos UTM V 9.308 to be installed. Mounting instructions The Sophos AP 100X can be mounted on a pole. A mounting kit is included in delivery.
Operating Instructions Technical specifications Sophos AP 100X Mounting Wall / Pole Chassis Metal housing, white IP Code 67 Maximum throughput 1.3 Gbps (5GHz / 802.11ac) + 450 Mbps (2.4GHz / 802.11n) Multiple SSIDs 8 per radio, 16 in total Number of radios 2 MIMO capabilities 3x3:3 LAN interfaces 1 x 10/100/1000 Base-TX Antenna 6 x external dipole antenna Antenna gain 4 dBi @ 2.4GHz, 6 dBi @5GHz Supported WLAN standards 802.
Operating Instructions Power-over-Ethernet injector Optionally included with AP 30, AP 50, AP 100 and AP 100X The PoE injector converts alternating current (AC) to direct current (DC), which is then provided over the Ethernet cable to power the Sophos Access Points AP 30, AP 50, AP 100 and AP 100X. Installation Warning: Do not use crossover cable between the PoE injector’s output port and the access point.
Operating Instructions Technical specifications PoE injector PD-3501/AC (AP 30) PoE injector PD-9001GR/AC (AP 50/AP 55/AP 55C/ AP 100/AP 100C/AP 100X) Chassis Plastic housing Plastic housing Input power AC input voltage: 90-264 VAC AC Input Voltage: 100 to 240 VAC AC input current: 0.5 A, 100-240 VAC AC Input Current: 0.8A @ 100-240 VAC AC frequency: 47/63 Hz AC Frequency: 50 to 60 Hz Output power voltage: 50 VDC Output power voltage: 55 VDC Power-over-Ethernet output (max.) Output power: 15.
