To prevent fire or shack hazard, do not expose the unit to rain or moisture. To avoid electrical shack, do not open the cabinet. Refer servicing to qualified personnel only. For the customers in the U.S.A. Ce This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and bad {excluding extremities: hands, wrists and feet).
Table of Contents Overview Features .. Applicable Models System Configuration Example Locations and Functions of Parts Attaching to the Camcorder .. Power Supply rmernsnmnrennan Operating on the Battery Pack Operating on AC Power Menu Settings .. Menu Items .. Setting the Menu Items Transmission Messages .. Error Messages .. Specifications Table of Consistent.
Overview The W LL-CAS0 is a wireless camera transmitter that transmits video and audio signals from a Camcorder with high quality using digital modulation/ demodulation technologies. You can select the transmission frequency in the range of 2406 to 2478 MHz in 1-MHz or 12-MHz steps. The standard transmission distance is approximately S00 m (with no obstruction) in High Output mode.
System Configuration Example Basic system Antenna + Down-converter {supplied with the W LL-RX50) Coaxial cable with N-type connectors IT W LL-RX50 Wireless Camera Receiver Camcorder + W LL-CAS0 Wireless Camera Transmitter + Battery pack ] System Monitor Overview © EE
Locations and Functions of Parts inside panel © CANCEL button © Digital center connector © DC LINE switch © TX ON button ! MENU knob Rear panel @ RF OUT connector I © i SPARE connector @ Battery attachment © DC IN connector | © DC DUT connector © CANCEL tuition Press the button to return to the upper menu layer ina menu operation. For details on menu operations, see “Menu Settings” on page 11. © Digital interface connector (40-pin) For data communication with a Camcorder.
The display will be automatically turned off if you do not operate the transmitter in normal Transmission mode fora while. To turn the display on again, press the DISPLAY button. © TX ON (transmission start) button Press {o start transmission. "To terminate transmission, turn off the power of the transmitter by setting the DC LINE switch to OFF, © DC LINE switch To turn the power to the unit ON/OFF. This button has no effect on the Camcorder. Turn the power to the Camcorder on and off on the Camcorder side.
Power Supply This transmitter operates on a battery pack or AC power (with an or AC-DNZB). Operating on the Battery Pack Before use, charge the battery pack with a battery charger. For details on charging method and time, refer to the manuals for the battery pack and battery charger. To attach a battery pack 1 Press the battery pack against the back of the transmitter, aligning the side line of the battery pack with the marching line on the transmitter. Battery pack Align these fines.
Menu Settings Advanced Menu ‘While holding the CANCEL button down, press the MENU knob. The Advanced Menu is displayed. . . . tem Sub menu Values (default) You can perform various settings using menus on the display. Freq Step — 12 MHz, 1 MHz (12 MHz) The unit provides the Main Menu and Advanced Menu, Custom Set | MOD 18QAM, SKIP (16QAM} and some of the mean items have sub menus. Code Rate | 3/4, 1/2 (1/2) The menus tripper you to set the following items. The Video 1.
Setting the Menu items 1 Set the DC LINE switch to ON to tum on the transmitter. The display lights. ‘When it turns to the status indications (see page 8), you can start the men operation. If the display is not on, press the DISPLAY button. 2 Totes the Main Menu items, press the MENU knob. To set the Advanced Menu items, press the MENU knob while holding the CANCEL nation pressed. The corresponding menu appears on the display. 3 Turn the MENU knob to move the cursor {to the item to be set.
3 Tum the MENU knob to display the desired value. Example: ‘Fo cancel the change Press the CANCEL button. The status in step 1 is restored, 4 Press the MENU knob. The question mark (7) changes back to the cursor Set other digits in the same manner. When all the digits have been set, press the CANCEL button to return to the upper layer (Main Menu or Advanced Menace. Ta release Menu mode, press the CANCEL button again. ‘The normal status display is restored.
Messages A message may be displayed according to input signals, set values, or operating statuses. Low Battery Reason: The power voltage is lower than the value specified on the menu. Measures: Replace the battery, or increase the power voltage. No Video Reason: No video signal is detected. Measures: Check the power to the Camcorder. Or check the consistency between the transmitter and the Camcorder. Or check the input signal to the SPARE connector.
rr Specifications General Power requirements 12 VDC Current consumption 770 mA Operating temperature 0°C to +40°C (+32°F 0 +104°F) Storage temperature —20°C to +60°C (°F to +140°F) Dimensions 97 x 209 x 152 mm inches) Mass 1.
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
