Reference Guide

WF-H800 (UC) [US/CaFR/LaES] 5-007-449-11(1)
WF-H800
Wireless Stereo Headset
Casque stéréo sans fil
https://rd1.sony.net/help/mdr/wfh800/h_zz/
5-007-449-11(1)
©2019 Sony Corporation
Printed in Malaysia
Imprimé en Malaisie
https://www.sony.net/
Reference Guide Manuel de référence Guía de referencia
Headset / Casque d’écoute:
WF-H800L, WF-H800R
FCC ID: AK8WFH800
IC: 409B-WFH800
5 V
MALAYSIA
WF-H800
5 V
MALAYSIA
WF-H800
INPUT: 5 V
IC: 409B-WFH800 CHARGING CASE
OUTPUT: 5 V
70 mA (L)
OUTPUT: 5 V
70 mA (R)
FCC ID: AK8WFH800
CANICES-3B / NMB-3B
MADE IN MALAYSIA
WF-H800
SONY CORP.
English
Wireless Stereo Headset
FOR UNITED STATES CUSTOMERS. NOT
APPLICABLE IN CANADA, INCLUDING IN THE
PROVINCE OF QUEBEC.
POUR LES CONSOMMATEURS AUX
ÉTATS-UNIS. NON APPLICABLE AU CANADA,
Y COMPRIS LA PROVINCE DE QUÉBEC.
Owner’s Record
The model and serial numbers are located on
the product.
Record them in the space provided above
and store them.
Model No.__________________________________
Serial No.___________________________________
CAUTION: Risk of fire and burns. Do not open,
crush, heat above 60 °C (140°F) or incinerate.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
Do not expose the batteries (battery pack or
batteries installed) to excessive heat such as
sunshine, fire or the like for a long time.
Do not subject the batteries to extreme low
temperature conditions that may result in
overheating and thermal runaway.
Do not dismantle, open or shred secondary cells
or batteries.
Do not expose cells or batteries to heat or fire.
Avoid storage in direct sunlight.
In the event of a cell leaking, do not allow the
liquid to come in contact with the skin or eyes. If
contact has been made, wash the affected area
with copious amounts of water and seek medical
advice.
Secondary cells and batteries need to be charged
before use. Always refer to the manufacturer’s
instructions or equipment manual for proper
charging instructions.
After extended periods of storage, it may be
necessary to charge and discharge the cells or
batteries several times to obtain maximum
performance.
Dispose of properly.
RECYCLING RECHARGEABLE BATTERIES
Rechargeable batteries are recyclable.
You can help preserve our environment by
returning your used rechargeable batteries to the
collection and recycling location nearest you.
For more information regarding recycling of
rechargeable batteries, visit http://www.sony.
com/electronics/eco/environmental-
management
Caution: Do not handle damaged or leaking
rechargeable batteries.
FOR UNITED STATES CUSTOMERS. NOT
APPLICABLE IN CANADA, INCLUDING IN THE
PROVINCE OF QUEBEC.
POUR LES CONSOMMATEURS AUX
ÉTATS-UNIS. NON APPLICABLE AU CANADA,
Y COMPRIS LA PROVINCE DE QUÉBEC.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
If you have any questions about this
product:
Visit: https://www.sony.com/electronics/
support
Contact: Sony Customer Information Service
Center at 1-800-222-7669
Write: Sony Customer Information Service
Center 12451 Gateway Blvd., Fort Myers, FL
33913
Supplier’s Declaration of Conformity
Trade Name : SONY
Model : WF-H800
Responsible Party : Sony Electronics Inc.
Address : 16535 Via Esprillo, San Diego, CA
92127 U.S.A.
Telephone Number : 858-942-2230
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful
interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
NOTE:
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/
TV technician for help.
This equipment must not be co-located or
operated in conjunction with any other
antenna or transmitter.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio
frequency (RF) Exposure Guidelines. This
equipment has very low levels of RF energy
that is deemed to comply without testing of
specific absorption rate (SAR).
For the customer in Canada
This device contains licence-exempt
transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the following
two conditions:
(1) This device may not cause interference;
and
(2) This device must accept any interference,
including interference that may cause
undesired operation of the device.
The available scientific evidence does not
show that any health problems are
associated with using low power wireless
devices. There is no proof, however, that
these low power wireless devices are
absolutely safe. Low power Wireless devices
emit low levels of radio frequency energy
(RF) in the microwave range while being
used. Whereas high levels of RF can produce
health effects (by heating tissue), exposure of
low-level RF that does not produce heating
effects causes no known adverse health
effects. Many studies of low-level RF
exposures have not found any biological
effects. Some studies have suggested that
some biological effects might occur, but such
findings have not been confirmed by
additional research. Wireless Stereo Headset
(WF-H800) has been tested and found to
comply with ISED radiation exposure limits
set forth for an uncontrolled environment
and meets RSS-102 of the ISED radio
frequency (RF) Exposure rules.
High volume may affect your hearing.
Do not use the unit while walking, driving or
cycling. Doing so may cause traffic accidents.
Do not use at a dangerous place unless the
surrounding sound can be heard.
The unit is not waterproof. If water or foreign
objects enter the unit, it may result in fire or
electric shock. If water or a foreign object enters
the unit, stop use immediately and consult your
nearest Sony dealer. In particular, be careful in
the following cases.
– When using the unit around a sink, etc.
Be careful that the unit does not fall into a sink
or container filled with water.
– When using the unit in the rain or snow, or in
humid locations
– When using the unit while you are sweaty
If you touch the unit with wet hands, or put the
unit in the pocket of a damp article of clothing,
the unit may get wet.
For details on the effect of contact to the human
body from the mobile phone or other wireless
devices connected to the unit, refer to the
instruction manual of the wireless device.
Install the earbuds firmly. Otherwise, they may
detach and be left in your ears, resulting in injury
or illness.
Never insert the USB plug when the main unit or
charging cable is wet. If the USB plug is inserted
while the main unit or charging cable is wet, a
short circuit may occur due to the liquid (tap
water, seawater, soft drink, etc.) attached to the
main unit or charging cable or due to foreign
matter, and cause abnormal heat generation or
malfunction.
There is a danger that this unit or its small parts
may be swallowed. After use, store the unit in
the charging case and store in a location out of
the reach of small children.
Note on static electricity
Static electricity accumulated in the body may
cause mild tingling in your ears. To reduce the
effect, wear clothes made from natural materials,
which suppress the generation of static
electricity.
IMPORTANT: THE FACTORY DEFAULT SETTING OF
THE VOICE GUIDANCE FOR THIS UNIT IS
ENGLISH.
The voice guidance can be heard from the unit
when:
• When powering on: “Power on”
• When powering off: “Power off”
• When the remaining battery level is low and
recharge is recommended: “Low battery, please
recharge headset”
• When automatically turning off due to low
battery: “Please recharge headset. Power off”
• When checking the remaining battery level:
“Battery fully charged” / “Battery about 70 %” /
“Battery about 50 %”
• When entering pairing mode: “Bluetooth
pairing”
• When establishing a Bluetooth connection:
“Bluetooth connected”
• When disconnecting a Bluetooth connection:
“Bluetooth disconnected”
Precautions
On BLUETOOTH® communications
• Bluetooth wireless technology operates within
a range of about 10 m (30 feet). The maximum
communication distance may vary depending
on the presence of obstacles (people, metal
objects, walls, etc.) or the electromagnetic
environment.
• Bluetooth communications may not be
possible, or noise or audio dropout may occur
under the following conditions:
– When there is a person between the unit and
the Bluetooth device. This situation may be
improved by positioning the Bluetooth device
so that it faces the antenna of the unit.
– When there is an obstacle, such as a metal
object or a wall, between the unit and the
Bluetooth device.
– When a Wi-Fi device or microwave oven is in
use, or microwaves are emitted near the unit.
– Compared to use indoors, use outdoors is
subjected little to signal reflection from walls,
floors, and ceilings, which results in audio
dropout occurring more frequently than use
indoors.
– The antenna is built into the unit as indicated
by the dotted line in the illustration below.
The sensitivity of the Bluetooth
communications can be improved by
removing any obstacles between the
connected Bluetooth device and the antenna
of this unit.
• Bluetooth and Wi-Fi (IEEE802.11b/g/n) devices
use the same frequency (2.4 GHz). When using
the unit near a Wi-Fi device, electromagnetic
interference may occur, resulting in noise,
audio dropout, or the inability to connect. If this
happens, try performing the following
remedies:
– Establish a connection between the unit and
the Bluetooth device when they are at least
10 m (30 feet) away from the Wi-Fi device.
– Turn off the Wi-Fi device when using the unit
within 10 m (30 feet) of the Wi-Fi device.
– Position the unit and the Bluetooth device as
near as possible to each other.
• Microwaves emitting from a Bluetooth device
may affect the operation of electronic medical
devices. Turn off this unit and other Bluetooth
devices in the following locations, as it may
cause an accident:
– in hospitals, near priority seating in trains,
locations where inflammable gas is present,
near automatic doors, or near fire alarms.
• The audio playback on this unit may be
delayed from that on the transmitting device,
due to the characteristics of Bluetooth wireless
technology. As a result, the sound may not be
in sync with the image when viewing movies or
playing games.
• This product emits radio waves when used in
wireless mode.
When used in wireless mode on an airplane,
follow flight crew directions regarding
permissible use of products in wireless mode.
• The unit supports security functions that
comply with the Bluetooth standard as a
means of ensuring security during
communication using Bluetooth wireless
technology. However, depending on the
configured settings and other factors, this
security may not be sufficient. Be careful when
communicating using Bluetooth wireless
technology.
• Sony shall assume no responsibility for any
damages or loss resulting from information
leaks that occur when using Bluetooth
communications.
• Connection with all Bluetooth devices cannot
be guaranteed.
– Bluetooth devices connected with the unit
must comply with the Bluetooth standard
prescribed by Bluetooth SIG, Inc., and must
be certified as compliant.
– Even when a connected device complies with
the Bluetooth standard, there may be cases
where the characteristics or specifications of
the Bluetooth device make it unable to
connect, or result in different control
methods, display, or operation.
– When using the unit to perform hands-free
talking on the phone, noise may occur
depending on the connected device or the
communication environment.
• Depending on the device to be connected, it
may require some time to start
communications.
If sound skips frequently during playback
• The situation may be improved by setting the
sound quality mode to “priority on stable
connection.” For details, refer to the Help Guide.
• The situation may be improved by changing
the wireless playback quality settings or fixing
the wireless playback mode to SBC on the
transmitting device. For details, refer to the
operating instructions supplied with the
transmitting device.
• When listening to music from a smartphone,
the situation may be improved by closing
unnecessary apps or restarting the
smartphone.
On the use of calling apps for smartphones
and computers
• This unit supports normal incoming calls only.
Calling apps for smartphones and computers
are not supported.
On charging the unit
• This unit can be charged using USB only. A
computer with a USB port or a USB AC adaptor
is required for charging.
• Be sure to use the supplied USB Type-C cable.
• When charging, the unit cannot be turned on
and the Bluetooth function cannot be used.
• Immediately wipe off any perspiration or water
on the charging port after use. If perspiration or
water is left on the charging port, it may impair
the ability to charge the unit.
• If the unit is not used for a long time, the
rechargeable battery may become depleted
quickly. The battery will be able to hold a
proper charge after it is discharged and
recharged several times. When storing the unit
for a long time, charge the battery once every
six months to prevent over-discharge.
• If the rechargeable battery becomes depleted
extremely quickly, it should be replaced with a
new one. Please contact your nearest Sony
dealer for a battery replacement.
If the unit does not operate properly
• Follow the procedure below to reset the unit.
Put the units into the charging case, then press
and hold the button on the left unit. When the
indicator (red) on the unit turns off after
flashing (after about 20 seconds), release the
button. Then, press and hold the button on the
right unit. When the indicator (red) on the unit
turns off after flashing (after about 20 seconds),
release the button. The pairing information and
other settings are retained even when the unit
is reset.
• If the problem persists even after the unit is
reset, perform the procedure below to initialize
the unit.
Put the units into the charging case, then press
and hold the buttons on the left and right unit
simultaneously. When the indicators (red) start
flashing (after about 10 seconds), release the
buttons. The indicators (blue) flash 4 times, the
unit is initialized, and the unit is reset to the
factory settings. When the unit is initialized, all
pairing information is deleted.
• After the unit is initialized, it may not connect
to your iPhone or computer. If this happens,
delete the pairing information of the unit from
the iPhone or computer, and then pair them
again.
Notes on wearing the unit
• After use, remove the headphones slowly.
• Because the earbuds achieve a tight seal in the
ears, forcibly pressing them in or quickly pulling
them out can result in eardrum damage.
When putting the earbuds into your ears, the
speaker diaphragm may produce a click sound.
This is not a malfunction.
Other notes
• Do not subject the unit to excessive shock.
• The Bluetooth function may not work with a
mobile phone, depending on the signal
conditions and the surrounding environment.
• If you experience discomfort while using the
unit, stop using it immediately.
• The earbuds may be damaged or deteriorate
with long-term use and storage.
Cleaning the unit
• When the outside of the unit is dirty, clean it by
wiping with a soft dry cloth. If the unit is
particularly dirty, soak a cloth in a dilute
solution of neutral detergent, and wring it well
before wiping. Do not use solvents such as
thinner, benzene, or alcohol, as they may
damage the surface.
• Turn the microphone hole downward and
gently tap it about five times towards a dry
cloth etc. If any water drops are left in the
microphone hole, it may cause corrosion.
• If you have any questions or problems
concerning this unit that are not covered in this
manual, please consult your nearest Sony
dealer.
Replacement parts: Long hybrid silicone
rubber earbuds
Please consult your nearest authorized Sony
retailer or www.sony.com for information
about replacement parts.
Location of the serial number label
Specifications
Headset
Power source:
DC 3.7 V: Built-in lithium-ion rechargeable
battery
DC 5 V: When charged using USB
Operating temperature:
0 °C to 40 °C (32 °F to 104 °F)
Rated power consumption:
1 W (Headset), 3 W (Charging case)
Usage hours:
When connecting via the Bluetooth device
Music playback time: Max. ##xx## hours
Communication time: Max. ##xx##
hours
Standby time: Max. ##xx## hours
Note: Usage hours may be shorter
depending on the Codec and the
conditions of use.
Charging time:
Approx. 1.5 hours (Headset)
(About ##xx## minutes of music playback
is possible after 10 minutes charging.)
Approx. 3 hours (Charging case)
Note: Charging and usage hours may be
different depending on the conditions of
use.
Charging temperature:
5°C to 35°C (41 °F to 95 °F)
Mass:
Approx. 7.6 g × 2 (0.27 oz × 2) (Headset)
Approx. 48 g (1.7 oz) (Charging case)
Included items:
Wireless Stereo Headset (1)
USB Type-C™ cable (USB-A to USB-C™)
(approx. 20 cm (7.88 in.)) (1)
Long hybrid silicone rubber earbuds (SS (1
line) (2), S (2 lines) (2), M (3 lines) (attached
to the unit at the factory) (2), L (4 lines) (2))
or (SS (red) (2), S (orange) (2), M (green)
(attached to the unit at the factory) (2),
L (light blue) (2))
Charging case (1)
Communication specification
Communication system:
Bluetooth Specification version 5.0
Output:
Bluetooth Specification Power Class 1
Maximum communication range:
Line of sight approx. 10 m (30 ft)
1)
Frequency band:
2.4 GHz band (2.4000 GHz - 2.4835 GHz)
Compatible Bluetooth profiles
2)
:
A2DP / AVRCP / HFP / HSP
Supported Codec
3)
:
SBC / AAC
Transmission range (A2DP):
20 Hz - 20,000 Hz (Sampling frequency
44.1 kHz)
1)
The actual range will vary depending on
factors such as obstacles between devices,
magnetic fields around a microwave oven,
static electricity, reception sensitivity,
antenna’s performance, operating system,
software application, etc.
2)
Bluetooth standard profiles indicate the
purpose of Bluetooth communications
between devices.
3)
Codec: Audio signal compression and
conversion format
Design and specifications are subject to change
without notice.
System requirements for
battery charge using USB
USB AC adaptor
A commercially available USB AC adaptor
capable of supplying an output current of 0.5 A
(500 mA) or more
Compatible iPhone/iPod
models
iPhone XS Max, iPhone XS, iPhone XR, iPhone X,
iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone 7,
iPhone SE, iPhone 6s Plus, iPhone 6s,
iPhone 6 Plus, iPhone 6, iPhone 5s,
iPod touch (6th generation)
(As of October 2019)
Trademarks
• Apple, iPhone, iPod and iPod touch are
trademarks of Apple Inc., registered in the U.S.
and other countries.
• Use of the Made for Apple badge means that
an accessory has been designed to connect
specifically to the Apple product(s) identified in
the badge, and has been certified by the
developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards.
• Android is a trademark of Google LLC.
• The Bluetooth® word mark and logos are
registered trademarks owned by the Bluetooth
SIG, Inc. and any use of such marks by Sony
Corporation is under license.
• The N-Mark is a trademark or registered
trademark of NFC Forum, Inc. in the United
States and in other countries.
• USB Type-C™ and USB-C™ are trademarks of
USB Implementers Forum.
• Other trademarks and trade names are those of
their respective owners.
Notes on the License
This product contains software that Sony uses
under a licensing agreement with the owner of
its copyright. We are obligated to announce the
contents of the agreement to customers under
requirement by the owner of copyright for the
software.
Please access the following URL and read the
contents of the license.
https://rd1.sony.net/help/mdr/sl/19b/
Disclaimer regarding
services offered by third
parties
Services offered by third parties may be
changed, suspended, or terminated without prior
notice. Sony does not bear any responsibility in
these sorts of situations.
Français
Casque stéréo sans fil
ATTENTION : Risque d’incendie et de brûlures.
Ne l’ouvrez pas, ne l’écrasez pas, ne le faites pas
chauffer à plus de 60 °C (140°F) ou ne l’incinérez
pas.
Ne pas installer l’appareil dans un espace clos,
tel qu’une bibliothèque ou une armoire
encastrée.
Ne pas exposer les piles (bloc-pile ou batteries
installées) à une chaleur excessive comme celle
produite par les rayons du soleil, les flammes,
etc. pendant une période prolongée.
Ne pas soumettre les batteries à des conditions
de température basse extrême qui pourraient
entraîner une surchauffe et un emballement
thermique.
Ne pas démonter, ouvrir ou déchiqueter les piles
ou batteries secondaires.
Ne pas exposer les piles ou batteries à la chaleur
ou au feu. Éviter tout rangement à la lumière
directe du soleil.
En cas de fuite d’une pile, ne pas laisser le
liquide entrer en contact avec la peau ou les
yeux. En cas de contact, laver la zone concernée
avec de grandes quantités d’eau et consulter un
médecin.
Les piles et batteries secondaires doivent être
chargées avant toute utilisation. Toujours se
reporter aux instructions du fabricant ou au
manuel de l’équipement pour prendre
connaissance des instructions de chargement
adéquates.
Après de longues périodes de rangement, il peut
être nécessaire de charger et décharger les piles
ou batteries à plusieurs reprises pour obtenir une
performance optimale.
Mettre au rebut de manière appropriée.
RECYCLAGE DES ACCUMULATEURS
RECHARGEABLES
Les accumulateurs rechargeables sont
recyclables.
Vous pouvez contribuer à préserver
l’environnement en rapportant les piles usées
dans un point de collection et recyclage le plus
proche.
Pour plus d’informations sur le recyclage des
accumulateurs, visitez http://www.sony.com/
electronics/eco/environmental-management
Avertissement: Ne pas utiliser des accumulateurs
rechargeables qui sont endommagées ou qui
fuient.
Pour la clientèle au Canada
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et
Développement économique Canada
applicables aux deux conditions suivantes :
1) l’appareil ne doit pas produire de
brouillage;
2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre
le fonctionnement
Les connaissances scientifiques dont nous
disposons n’ont mis en évidence aucun
problème de santé associé à l’usage des
appareils sans fil à faible puissance. Nous ne
sommes cependant pas en mesure de
prouver que ces appareils sans fil à faible
puissance sont entièrement sans danger. Les
appareils sans fil à faible puissance émettent
une énergie fréquence radioélectrique (RF)
très faible dans le spectre des micro-ondes
lorsqu’ils sont utilisés. Alors qu’une dose
élevée de RF peut avoir des effets sur la
santé (en chauffant les tissus), l’exposition à
de faibles RF qui ne produisent pas de
chaleur n’a pas de mauvais effets connus sur
la santé. De nombreuses études ont été
menées sur les expositions aux RF faibles et
n’ont découvert aucun effet biologique.
Certaines études ont suggéré qu’il pouvait y
avoir certains effets biologiques, mais ces
résultats n’ont pas été confirmés par des
recherches supplémentaires. Casque stéréo
sans fil (WF-H800) a été testé et jugé
conforme aux limites d’exposition aux
rayonnements ISDE énoncées pour un
environnement non contrôlé et respecte les
règles d’exposition aux fréquences
radioélectriques (RF) CNR-102 de l’ISDE.
Un volume élevé peut affecter votre ouïe.
N’utilisez pas l’appareil pendant que vous
marchez, conduisez ou faites du vélo. Vous
risqueriez de provoquer des accidents de la
circulation.
Ne l’utilisez pas à un endroit dangereux, à moins
que vous puissiez entendre les sons
environnants.
L’appareil n’est pas résistant à l’eau. Si de l’eau
ou des corps étrangers pénètrent dans l’appareil,
cela peut entraîner un incendie ou un choc
électrique. Si de l’eau ou un corps étranger
pénètre dans l’appareil, cessez immédiatement
de l’utiliser et consultez votre détaillant Sony le
plus proche. N’oubliez pas de suivre, notamment,
les précautions ci-dessous.
– Utilisation près d’un évier, etc.
Veillez à ce que l’appareil ne tombe pas dans
un évier ou un récipient rempli d’eau.
– Utilisation sous la pluie ou la neige ou dans des
endroits humides
– Utilisation pendant que vous transpirez
Si vous touchez l’appareil avec les mains
mouillées ou le mettez dans la poche d’un
vêtement humide, l’appareil peut devenir
mouillé.
Pour plus de renseignements sur l’effet de
contact sur le corps humain que peut avoir un
téléphone mobile ou autre périphérique sans fil
connecté à l’appareil, consultez le manuel
d’instructions du périphérique sans fil.
Installez fermement les oreillettes. Sinon, elles
peuvent se détacher et rester dans vos oreilles,
entraînant des blessures ou des maladies.
N’insérez jamais la fiche USB lorsque l’appareil
principal ou le câble de chargement est mouillé.
Si la fiche USB est insérée pendant que l’appareil
principal ou le câble de chargement est mouillé,
un court-circuit pourrait être causé par le liquide
(eau du robinet, eau de mer, boisson gazeuse,
etc.) présent sur l’appareil principal ou le câble
de chargement ou par un corps étranger,
entraînant un dégagement de chaleur anormal
ou un problème de fonctionnement.
Il y a un risque que cet appareil ou ses petites
pièces puissent être avalés. Après l’utilisation,
rangez l’appareil dans l’étui de chargement et
rangez-le dans un endroit hors de portée des
enfants.
Remarque sur l’électricité statique
L’électricité statique accumulée dans votre corps
peut causer une légère sensation de picotement
dans vos oreilles. Pour réduire l’effet, portez des
vêtements fabriqués à partir de matériaux
naturels, qui permettent d’éviter la production
d’électricité statique.
IMPORTANT : LE RÉGLAGE D’USINE PAR DÉFAUT
DU GUIDAGE VOCAL POUR CET APPAREIL EST
L’ANGLAIS.
Le guidage vocal peut se faire entendre en
provenance de l’appareil :
• Lors de la mise en marche : « Power on »
(Marche)
• Lors de la mise en arrêt : « Power off » (Arrêt)
• Lorsque le niveau restant de la batterie est
faible et qu’une recharge est recommandée :
«Low battery, please recharge headset »
(Batterie faible, veuillez recharger le casque
d’écoute)
• Lors de la mise en arrêt automatique en raison
de la batterie faible : « Please recharge headset.
Power off » (Veuillez recharger le casque
d’écoute. Arrêt)
• Lors de la vérification du niveau restant de la
batterie : « Battery fully charged » / « Battery
about 70% » / « Battery about 50% » (Batterie
entièrement chargée / Batterie environ 70 % /
Batterie environ 50 %)
• Lorsque l’appareil passe en mode de
jumelage: « Bluetooth pairing » (Jumelage
Bluetooth)
• Lors de l’établissement d’une connexion
Bluetooth : « Bluetooth connected » (Bluetooth
connecté)
• Lors de la désactivation d’une connexion
Bluetooth : « Bluetooth disconnected »
(Bluetooth déconnecté)
Précautions
À propos des communications
BLUETOOTH®
• La technologie sans fil Bluetooth fonctionne
dans un rayon d’environ 10m (30 pieds). La
distance maximale de communication peut
varier en fonction de la présence d’obstacles
(personnes, objets métalliques, murs, etc.) ou
de l’environnement électromagnétique.
• Les communications Bluetooth peuvent ne pas
être possibles ou du bruit ou des pertes
sonores peuvent se produire dans les
conditions suivantes:
– Lorsqu’il y a une personne entre l’appareil et
le périphérique Bluetooth. Cette situation
peut être améliorée en plaçant le
périphérique Bluetooth de manière à ce qu’il
soit face à l’antenne de l’appareil.
– Lorsqu’il y a un obstacle, tel qu’un objet
métallique ou un mur, entre l’appareil et le
périphérique Bluetooth.
– Lorsqu’un périphérique Wi-Fi ou un four à
micro-ondes est en cours d’utilisation ou que
des micro-ondes sont émises à proximité de
l’appareil.
– Comparativement à une utilisation intérieure,
l’utilisation extérieure est peu soumise à la
réflexion du signal sur les murs, les sols et les
plafonds, ce qui entraîne une perte sonore
plus fréquente que lors de l’utilisation à
l’intérieur.
– L’antenne est intégrée à l’appareil comme
l’indique la ligne en pointillé sur l’illustration
ci-dessous. La sensibilité des communications
Bluetooth peut être améliorée en retirant tout
obstacle entre le périphérique Bluetooth
connecté et l’antenne de cet appareil.