4-580-170-04 (1) Video Projector Operating Instructions Before operating the unit, please read this manual and supplied Quick Reference Manual thoroughly and retain them for future reference.
Table of Contents Location of Controls Using Network Features Front/Right Side ................................ 4 Rear/Left Side/Bottom ...................... 5 Remote Control ................................. 6 Displaying the Control Window of the Unit with a Web Browser ............. 43 Operating the Control Window ........ 44 Switching the Page .....................44 Setting the Access Limitation ....44 Confirming the Information Regarding the Unit ..................
Index ................................................
Location of Controls Front/Right Side Warning indicators Warning indicators Others a ON/STANDBY indicator (page 49) i Lamp cover (page 52) j 3D Sync Transmitter b WARNING indicator (page 49) Located on the inside of the lamp cover. Connectors k Ventilation holes (exhaust) c LAN connector (page 43) l Ventilation holes (intake) (page 54) d USB connector (page 51) m Remote control detector (page 8) e HDMI 1/HDMI 2 connector (page 13) f REMOTE connector Connects to a computer, etc.
Rear/Left Side/Bottom The buttons on the control panel have the same names as those on the remote control.
a LIGHT button Remote Control Illuminates the buttons on the remote control.
Connections and Preparations This section describes how to install the unit and screen, how to connect the equipment from which you want to project the picture, etc. Note Installing the Unit When using a screen with an uneven surface, stripes pattern may rarely appear on the screen depending on the distance between the screen and the unit or the zooming magnifications. This is not a malfunction of the unit.
Note Adjusting the Picture Position Depending on the installation location of the unit, you may not be able to control it with the remote control. In this case, point the remote control at the remote control detector of the unit or the screen. Project an image on the screen and then adjust the picture position. 1 After connecting the AC power cord to the unit, plug the AC power cord into a wall outlet. The ON/STANDBY indicator lights in red and the unit goes into standby mode.
3 4 Adjust the focus. Press the LENS ADJUSTMENT (FOCUS) button to display the Lens Focus adjustment window (test pattern). Then adjust the focus of the picture by pressing the M/m/
5 Adjust the picture position. To adjust the horizontal position Press the LENS ADJUSTMENT (SHIFT) button to display the Lens Shift adjustment window (test pattern). Then adjust to the proper position of the picture by pressing the M/m/
Range of movement of the projected picture To adjust the vertical position Press M/m. 0.85V The picture projected on the screen moves up by a maximum of 85% or moves down by a maximum of 80% of the screen height from the center of the lens. 0.31H 0.31H Projected Picture Side view 0.
Lens adjustment window (test pattern) 1.78:1 (16:9) 1.33:1 (4:3) 2.35:1 1.85:1 The dashed lines show the screen sizes of each aspect ratio.
Connecting to Video Equipment or a Computer You can enjoy high picture quality by connecting a DVD player/recorder, Blu-ray Disc player/ recorder, or PlayStation® equipped with HDMI output to the HDMI input of the unit. When making connections, be sure to do the following: • Turn off all equipment before making any connections. • Use the proper cables for each connection. • Insert the cable plugs properly; poor connection at the plugs may cause a malfunction or poor picture quality.
Notes • Use a high-speed HDMI cable. With a standard HDMI cable, images of 1080p, DeepColor, 3D video and 4K video may not be displayed properly. • When connecting an HDMI cable to the unit, make sure the V mark on the upper part of the HDMI input of the unit and the v mark on the connector of the cable is set at the same position. • If the picture from equipment connected to the unit with an HDMI cable is not correct, check the settings of the connected equipment.
Projecting This section describes how to operate the unit to view the picture from the equipment connected to the unit. It also describes how to adjust the quality of the picture to suit your taste. Turning Off the Power Projecting the Picture 1 Turn on both the unit and the equipment connected to the unit. 2 Press INPUT to display the input palette on the screen. 1 Press the ?/1 (ON/STANDBY) button. A message “POWER OFF?” appears on the screen.
Adjusting/Setting the 3D functions Watching 3D Video Images You can adjust/set the 3D functions by pressing the 3D button on the remote control or with the “3D Settings” of the Function menu. For details, see “3D Settings” (page 36). You can enjoy powerful 3D video images, such as from 3D games and 3D Blu-ray Discs, using the optional Active 3D Glasses (TDG-BT500A). 1 Using the 3D Glasses 1 Turn on the HDMI equipment for 3D compatibility connected to the unit, then play the 3D content.
Top or side view Using the Picture Position Projector You can store up to five combinations of lens settings (focus, picture size, picture position), aspect ratio, and blanking. These settings can be recalled. 10 m 10 m 10 m 1 Press POSITION. 10 m The Picture Position selecting palette is displayed. 2 Press POSITION repeatedly, or press M/m/ to select the position. The settings of the position selected is recalled.
Image of the lens moving In the example below, the images with aspect ratio of 1.78:1 (16:9) and 2.35:1 are projected on a 2.35:1 screen. When a 1.78:1 (16:9) image is input When a 2.35:1 image is input Press the POSITION button. The 2.35:1 image expands to fill the screen. Notes • After you have selected and confirmed the lens position, the lens starts to move. Do not touch, or place anything near, the lens, otherwise it may cause injury or a malfunction.
Selecting the Aspect Ratio According to the Video Signal You can select an aspect ratio best suited for the video signal received. Press ASPECT. ASPECT button Each time you press the button, you can select the “Aspect” setting.You can also select it using the menu (page 33). Original image Recommended setting and resultant images 1.85:1 Zoom 1.85:1 Squeezed 1.85:1 2.35:1 Zoom 2.35:1 Squeezed 2.
Original image Recommended setting and resultant images Normal 1.78:1 (16:9) 1.33:1 (4:3) 1.33:1 (4:3) with side panels V Stretch 2.
Original image Recommended setting and resultant images Stretch Squeezed Notes • Selectable aspect modes vary depending on the input signal (page 62). • The aspect cannot be selected for an input signal from a computer, or an input signal with a resolution of 4096 × 2160 (page 57). Notes on switching the “Aspect” setting • Select the aspect mode taking into account that changing the aspect ratio of the original picture will provide a different look from that of the original image.
Selecting the Picture Viewing Mode You can select the picture viewing mode that best suits the type of video source or room conditions. You can save and use different preset modes for 2D/3D respectively. CALIBRATED PRESET buttons Press one of the CALIBRATED PRESET buttons. Setting items Description CINEMA FILM 1 Picture quality suited to reproducing the highly dynamic and clear images typical of master positive film.
Using the Menus This section describes how to make various adjustments and settings using the menus. Note The menu displays used for the explanation may be different from the actual menu display. Operation through the Menus The unit is equipped with an on-screen menu for making various adjustments and settings. If you select an item name followed by an arrow (B), the next menu window with setting items appears. 1 Press MENU. 3 Press M/m to select an item you want to set or adjust and press , or .
Setting menu To reset the picture that has been adjusted Select “Reset” from the Picture menu. When the screen display appears, select “Yes” using < and press . All of the following settings are reset to its factory preset value: “Reality Creation,” “Cinema Black Pro,” “Motionflow,” “Contrast,” “Brightness,” “Color,” “Hue,” “Color Temp.
Picture Menu The Picture menu is used for adjusting the picture. Note These items may not be available, depending on the type of input signal. For details, see “Input Signals and Adjustable/Setting Items” (page 59). Item names in brackets represent those printed on the remote control. Setting items Description Calib. Preset [CALIBRATED PRESET] You can select the picture viewing mode that best suits the type of video source or the environment.
Setting items Description Reality Creation [REALITY CREATION] Adjusts the detail and noise processing of images. (Super-resolution function) On: Adjusts the settings of “Reality Creation.” Database: Select “Normal” or “Mastered in 4K.” “Mastered in 4K” provides image quality suitable for Blu-ray Disc™ “Mastered in 4K” releasing from Sony Pictures Home Entertainment. Resolution: When you increase the setting value, the texture and detail of the picture become sharper.
Setting items Description Motionflow [MOTIONFLOW] Impulse: Reproduces original picture quality. Provides cinema-like picture, which may flicker. Combination: Reduces motion blur while maintaining brightness for high-speed picture content. Smooth High: Provides smoother picture movement; especially effective for film-based content. Smooth Low: Provides smoother picture movement for standard use. True Cinema: Images, such as a movie created in 24 frames per second, are reproduced at the original framerate.
Setting items Description Sharpness [SHARPNESS] Sharpens the outline of the picture, or reduces the noise. The higher the setting, the sharper the picture. The lower the setting, the softer the picture, thus reducing the noise. You can make adjustments by pressing the SHARPNESS +/- on the remote control. Expert Setting NR (Noise Reduction) Reduces the roughness or noise of the picture. Auto: Detects the noise level to reduce the roughness or noise of the picture automatically.
Setting items Color Correction Description On: Adjusts Hue, Saturation or Brightness of the selected colors. Repeat steps 1 and 2 described below to specify the target color. 1 Press M/m to select “Color Select,” then press
Setting items Color Space [COLOR SPACE] Description Converts the color space. BT.709: An ITU-R BT.709 color space, which is used for highdefinition television broadcast or Blu-ray Disc. The color space is equivalent to sRGB. BT.2020: The color space is wider than BT.709. Use this setting when playing back HDR content. Color Space 1: The color space suited for watching TV programs and video images, such as sport, concerts, etc.
Advanced Picture Menu You can adjust the gaps in color that have occurred after a long period of use. Notes • Auto Calibration results in relatively coarse calibration. No warranty is given for the color settings to be the same as the factory default values. • While performing “Pre Check” or “Adjust,” the colors are projected automatically. This is not a malfunction. • Do not turn off the power or operate the remote control or control panel during “Pre Check” or “Adjust”, as the process may be canceled.
Screen Menu You can set the picture size, aspect mode, etc. Note These items may not be available, depending on the type of input signal. For details, see “Input Signals and Adjustable/Setting Items” (page 59). Item names in brackets represent those printed on the remote control. Setting items Description Picture Position [POSITION] You can store up to five combinations of lens settings, aspect ratio, and blanking. After setting the lens, aspect, and blanking, select from “1.85:1,” “2.
Setting items Description Aspect [ASPECT] You can set the aspect ratio of the picture to be displayed for the current input signal (page 19). You can set the function only when a video signal other than a resolution of 4096 × 2160 pixels is input. 1.85:1 Zoom: A 1.85:1 aspect ratio picture is displayed in its original aspect ratio, enlarged so that black bands do not appear at the top and bottom of the screen. 2.35:1 Zoom: A 2.
Setup Menu The Setup menu is used to change the factory preset settings, etc. Setting items Description Status Sets whether or not the on-screen display is displayed. Set to “Off” to turn off the on-screen displays except for certain menus, message when turning off the power, and warning messages. Language Selects the language used in the menu and on-screen displays. Menu Position You can change the position to display the menu on the screen.
Setting items Description Network Management On: Set when connected to the network and continuously communicating with the projector control equipment. Note When Network Management is set to “On,” the network function is continuously enabled. Set Network Management to “Off” for normal use. If you set to “On,” the power consumption increases. Power Saving Sets the power saving mode. Standby: If no signal is input for 10 minutes, power is turned off automatically and the projector goes into standby mode.
Function Menu The Function menu is used for changing the settings of the various functions of the unit. Setting items Description 3D Settings You can change the settings of the 3D function. 2D-3D Display Sel. For Switching the video images to “2D” or “3D.” Auto: Displays 3D video images when HDMI signals with 3D information* are input. Displays 2D video images when other signals are input. 3D: Displays 3D video images according to the 3D system selected in “3D Format.
Setting items 3D Depth Adjust Description For adjusting the depth of the 3D video images on the screen. The setting can be made only when a 3D Format other than “Simulated 3D” is selected. Depth Front Normal Depth We recommend that “3D Depth Adjust” be set to “0.” The 3D video images may be difficult to perceive, depending on the setting of “3D Depth Adjust.” Simulated 3D Effect For adjusting the 3D effect when 2D content is converted to 3D video images.
Items Locked by Settings Lock Group 1 Group 2 Picture menu Setup menu Reset Reality Creation Advanced Iris Contrast Enhancer Lamp Control Motionflow Contrast Brightness Color Hue Color Temp. Sharpness NR MPEG NR Smooth Gradation Film Mode Gamma Correction Color Correction Clear White x.v.
Installation Menu The Installation menu is used for changing the installation settings. Setting items Description Image Flip Flips the picture on the screen horizontally and/or vertically. HV: Flips the picture horizontally and vertically. H: Flips the picture horizontally. V: Flips the picture vertically. Off: The picture does not flip. Use this item for installation for the backside projection or ceiling installation.
Setting items Description Panel Alignment This feature allows you to adjust the gaps in the color of characters or the picture on the screen. Adjust: Adjusts the gaps in the colors selecting “Adjust Color” or “Adjust Item.” Adjust Item: Selects how to make adjustments from below. Shift: Shifts the whole picture and makes adjustments. Zone: Selects the desired range and makes adjustments. Adjust Color: Assigns the desired color to adjust the gaps in color.
Setting items Description Network Setting Perform internet protocol settings. IPv4 Setting IP Address Setup: Selects the IP address setting method. Auto (DHCP): The IP address is assigned automatically from the DHCP server such as a router. Manual: Specifies the IP address manually. When “Manual” is selected for “IP Address Setup,” select the item with the
Information Menu The Information menu displays the model name, serial number, input signal type, software version and the cumulated hours of usage of the lamp. Model name Serial No. Signal type Software version Items Description Model Name Displays the model name Serial No. Displays the serial number. Signal type Displays the type of the input signal. When input signals with 3D information are input, the type of input signals and the 3D format are displayed.
Using Network Features Connection to the network allows you to operate the following features: • Checking the current status of the unit via a Web browser. • Making the network settings for the unit. • Network monitoring and controlling with control protocol (SDAP [Advertisement], SDCP [PJ Talk], DDDP [AMX], Crestron RoomView, Control4). Displaying the Control Window of the Unit with a Web Browser 1 Connect the LAN cable.
Operating the Control Window Switching the Page Click one of the Page Switching buttons to display the desired setting page. Once you make the network settings, you can open the Control window only by performing step 3 of this procedure. Page Switching buttons Setting the Access Limitation You can limit a user for accessing any particular page.
Entry area for [Administrator] Entry area for [User] The password can be changed in the Password page in the Setup page. When you change the password, input a new password after deleting the password (*****) that was set. The password of the administrator and user should be 8 to 16 characters that includes both alphabet and numeric characters. Alphabet is case-sensitive. The default password “Projector” cannot be set as a new password.
Error Handling Troubleshooting If the unit appears to be operating erratically, try to diagnose and correct the problem using the following instructions. If the problem persists, consult with qualified Sony personnel. Power Symptom Cause and Remedy The power is not turned on. The power may not turn on if you turn the power off with ?/ 1 (ON/STANDBY) button and turn it on again in a short time. After about 1 minute, turn the power on. – Close the lamp cover securely, then tighten the screws securely.
Symptom Cause and Remedy Page The color of characters or Select the desired color registration in “Panel Alignment” of the Installation menu. the picture is not appropriate. 40 Image is left on the screen. (image retention) – When high contrast non-moving images are displayed for a long period of time, there may be some image retention on the screen. This is only a temporary condition. Turning off the power for a while will eliminate the retained image.
3D video images Symptom Cause and Remedy Page The video image does not Check if the 3D glasses are turned on. seem like 3D video Make sure that the battery in the 3D glasses could be weak images. or is sufficiently charged. 16 – Set “2D-3D Display Sel.” to “Auto” or “3D.” 36 Check if the input signals are compatible 3D signals. 60 The 3D signals may not be input depending on the specifications of the connected AV selector/AV amplifier/ external equipment.
Warning Indicators The ON/STANDBY or WARNING indicator lights up or flashes if there is any trouble with your projector. ON/STANDBY indicator Flashing/Lighting indicators The number of flashes Cause and Remedy Twice Close the lamp cover securely, then tighten the screws securely (page 53). Three times The temperature of lamp is unusually high. Turn off the power and wait for the lamp to cool, then turn on the power again. If the symptom persists, the lamp may be at the end of its service life.
Message Lists Warning messages Symptom Cause and Remedy Page High temp.! Lamp off in 1 min. Turn off the power. – Check to ensure that nothing is blocking the ventilation holes. 4, 5 Frequency is out of range! Frequency is out of range. Input a signal that is within the acceptable frequency range of the unit. 57 Please replace the Lamp. It is time to replace the lamp. Replace the lamp. If this message appears again after you replace the lamp, the lamp replacement process is not complete.
Others Updating the Software About the x.v.Color • “x.v.Color” is a promotion name given to the products that have the capability to realize a wide color space based on the xvYCC specifications and is a trademark of Sony Corporation. • xvYCC is an international standard of the technical specifications of the extendedgamut color space for video signals. The color gamut of xvYCC is wider than the one of sRGB that is used with the current television system.
• Be sure to turn off the unit and unplug the power cord before replacing the lamp, then check the ON/STANDBY indicator has already been turned off. Replacing the Lamp The lamp used for the light source has a certain lifespan. When the lamp dims, the color balance of the picture becomes strange, or “Please replace the Lamp.” appears on the screen, the lamp may be exhausted. Replace the lamp with a new one (not supplied) without delay.
6 5 Push in the new lamp by the handle securely until it reaches the end, and then tighten the 3 screws. Loosen the 3 screws on the lamp with the Phillips screwdriver. Hold up the handle, then pull the lamp straight out. Note Be careful not to touch the optical block inside the unit. 7 Close the lamp door (inner cover), and then tighten the screw. 8 Close the lamp cover. Handle Notes • Do not loosen other screws except the 3 specified screws. • Hold the lamp by the handle to remove and attach it.
9 Wipe dust off the ventilation holes (intake) with a soft cloth. • The unit will not turn on unless the lamp cover are securely closed. • To clear a message displayed on the screen, press any button either on the remote control or the control panel of the unit once. Note on replacing the lamp when broken, in the case of a ceiling installation If the lamp breaks, broken lamp pieces may scatter and cause injury.
Cleaning Cleaning the cabinet • To remove dust from the cabinet, wipe gently with a soft cloth. If dust is persistent, wipe with a soft cloth slightly moistened with a diluted mild detergent solution. • Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. • Clean the unit with a cleaning cloth. Wiping with a dirty cloth may scratch the unit.
Specifications Item Description Display system SXRD panel, projection system Display device Size of effective display area Number of pixels 0.74-inch (18.8 mm) SXRD 26,542,080 pixels (8,847,360 pixels × 3) Projection lens 2.06 times zoom lens (motorized) f = 21.7 mm to 44.7 mm F3.0 to F4.
Notes * Only the HDMI 2 input is compatible with HDCP 2.2. • The values for mass and dimensions are approximate. • Not all optional accessories are available in all countries and area. Please check with your local Sony Authorized Dealer. • Information on accessories in this manual is current as of September 2015. Design and specifications of this unit and its optional accessories are subject to change without notice.
Preset memory no. Preset signal (resolution) fH (kHz) fV (Hz) Sync 71 1920 × 1080/60i (Frame packing) 1080/60i (1920 × 1080i) 67.500 60.000 – 72 1920 × 1080/50i (Frame packing) 1080/50i (1920 × 1080i) 56.250 50.000 – 74 3840 × 2160/60p* 3840×2160/60p (3840 × 2160) 135.000 60.000 – 75 3840 × 2160/50p* 3840 × 2160/50p (3840 × 2160) 112.500 50.000 – 76 4096 × 2160/60p* 4096 × 2160/60p (4096 × 2160) 135.000 60.000 – 77 4096 × 2160/50p* 4096 × 2160/50p (4096 × 2160) 112.
Input Signals and Adjustable/Setting Items The items in the menus available to adjust differ depending on the input signal. The following tables indicate them. The items that cannot be adjusted/set are not displayed in the menu.
z: Adjustable/can be set –: Not adjustable/cannot be set *1: For further details, refer to the tables in “Motionflow” (page 63). Screen menu Item Aspect*1 Input signal Component signal Video GBR signal Computer signal (excluding preset z (excluding preset memory numbers 76 memory numbers 78, to 79 and 96) 79 and 96) z – z: Adjustable/can be set –: Not adjustable/cannot be set *1: For further details, refer to the tables in “Aspect Mode” (page 62).
3D signals Item 720/60p, 720/50p 1080/60i, 1080/50i 1080/24p 1080/60p, 1080/50p Motionflow*1 z z z z NR – – – – MPEG NR – – – – Smooth Gradation – – – – Film Mode – z – – x.v.Color z z z z HDR – – – – Aspect*2 z z z z z: Adjustable/can be set –: Not adjustable/cannot be set *1: The item is not available for Frame Packing/Over-Under on 720/60p, or Over-Under on 1080/ 60p. *2: For further details, refer to the tables in “Aspect Mode” (page 62).
Aspect Mode Selectable items vary depending on the type of input signal or 3D format. For details, see the tables below. Items that cannot be selected are not displayed in the menu. 2D Acceptable signals 4096 × 2160 3840 × 2160 1920 × 1080 1280 × 720 720 × 480 720 × 576 Others Preset memory number (page 57) 76 to 79, 96 74, 75, 93 to 95 7, 8, 10 to 14 5, 6 26, 32, 37, 45, 47, 50, 55 – 1.85:1 Zoom – – z z 2.
Motionflow Selectable items vary depending on the type of input signal or 3D format. For details, see the tables below. Items that cannot be selected are not displayed in the menu.
Picture menu Item Storage conditions Calib. Preset For each input connector Reset For each input connector and Calib. Preset Reality Creation Advanced Iris Contrast Enhancer Lamp Control Motionflow Contrast Brightness Color Hue Color Temp. D93-D55 Custom 1-5 Gain R For each Color Temp., D93-D55 and Custom 1-5 Gain G Gain B Bias R Bias G Bias B Sharpness For each input connector and Calib. Preset NR MPEG NR Smooth Gradation Film Mode Gamma Correction Color Correction Clear White x.v.
Projection Distance and Lens Shift Range The projection distance refers to the distance between the front of the lens and the projected surface. Projection distance L Projected image Front of the lens The lens shift range represents the distance in percent (%) by which the lens can be shifted from the center of the projected image.
When projecting in 1.90:1 (Native Full Display 17:9) format 1.90 1 Projection distance Unit: m (inches) Projection image size Diagonal Width × Height 80" (2.03 m) 1.80 × 0.95 (71 × 37) Projection distance L 2.32 – 4.77 (91 – 187) 100" (2.54 m) 2.25 × 1.18 (88 × 47) 2.90 – 5.97 (115 – 235) 120" (3.05 m) 2.70 × 1.42 (106 × 56) 3.49 – 7.18 (138 – 282) 150" (3.81 m) 3.37 × 1.78 (133 × 70) 4.38 – 8.98 (173 – 353) 200" (5.08 m) 4.49 × 2.37 (177 × 93) 5.85 – 11.
When projecting in 1.78:1 (16:9) format 1.78 Video display area 1 Projection area Projection distance Unit: m (inches) Projection image size Diagonal Width × Height 80" (2.03 m) 1.77 × 1.00 (70 × 39) Projection distance L 2.44 – 5.01 (96 – 197) 100" (2.54 m) 2.21 × 1.25 (87 × 49) 3.05 – 6.28 (121 – 247) 120" (3.05 m) 2.66 × 1.49 (105 × 59) 3.67 – 7.55 (145 – 297) 150" (3.81 m) 3.32 × 1.87 (131 × 74) 4.60 – 9.44 (181 – 371) 200" (5.08 m) 4.43 × 2.49 (174 × 98) 6.15 – 12.
When projecting in 2.35:1 format 2.35 Video display area 1 Projection area Projection distance Unit: m (inches) Projection image size Diagonal Width × Height 80" (2.03 m) 1.87 × 0.80 (74 × 31) Projection distance L 2.41 – 4.96 (95 – 195) 100" (2.54 m) 2.34 × 0.99 (92 × 39) 3.02 – 6.22 (119 – 244) 120" (3.05 m) 2.80 × 1.19 (110 × 47) 3.64 – 7.47 (143 – 294) 150" (3.81 m) 3.51 × 1.49 (138 × 59) 4.55 – 9.35 (180 – 368) 200" (5.08 m) 4.67 × 1.99 (184 × 78) 6.08 – 12.
Dimensions Front Unit: mm (inches) 495.6 (19 1/2) 247.8 (9 3/4) Center of the lens 108 (4 1/4) 195.3 (7 11/16) 202.3 (7 31/32) 247.8 (9 3/4) Bottom Unit: mm (inches) 98 (3 27/32) 98 (3 27/32) 81.5 (3 7/32) 81.5 (3 7/32) 187.9 (7 13/32) 187.9 (7 13/32) Front of the cabinet 87.3 (3 7/16) 142.8 (5 5/8) 150.6 (5 15/16) 408.9 (16 3/32) 463.6 (18 1/4) 69 7.
The distance between the front of the lens and the front of the cabinet Unit: mm (inches) 36.
Side view Unit: mm (inches) 213.5 (8 13/32) 130 (5 1/8) Front of the cabinet 258.5 (10 3/16) 463.6 (18 1/4) Top view Unit: mm (inches) 213.4 (8 13/32) 130 (5 1/8) Front of the cabinet 258.5 (10 3/16) Upper ceiling mount bracket Center of the supporting pole (The center of the supporting pole is different from that of the unit.
the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price.
translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1.
automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License.
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
programs; and that you are informed that you can do these things. To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you.
definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it).
When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgement: 4.
This product includes software developed by Danga Interactive, Inc. =============================== THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgement: “This product includes cryptographic software written by Eric Young (eay@cryptsoft.
other dealings in this Software without prior written authorization of the copyright holder. =============================== In the following statement, the phrase “this text’’ refers to portions of the system documentation. Portions of this text are reprinted and reproduced in electronic form in the second BSD Networking Software Release, from IEEE Std 1003.
libevent LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR HOLDERS INCLUDED IN THIS NOTICE BE LIABLE FOR ANY CLAIM, OR ANY SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
Copyright (c) 2003 Michael A. Davis evport.c: Copyright (c) 2007 Sun Microsystems ht-internal.h: Copyright (c) 2002 Christopher Clark minheap-internal.h: Copyright (c) 2006 Maxim Yegorushkin ============== The arc4module is available under the following, sometimes called the “OpenBSD” license: Copyright (c) 1996, David Mazieres Copyright (c) 2008, Damien Miller
documentation and/or other materials provided with the distribution. 3. The name of any author may not be used to endorse or promote products derived from this software without their specific prior written permission. ALTERNATIVELY, this product may be distributed under the terms of the GNU General Public License, in which case the provisions of the GNU GPL are required INSTEAD OF the above restrictions.
* Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/ or other materials provided with the distribution. * Neither the name of the University of Cambridge nor the name of Google Inc.
Connecting to Video equipment or a computer .......................................... 13 Connectors ................................................. 4 Contrast ................................................... 27 Contrast Enhancer ................................... 26 Control panel .............................................5 Index Numerics 3D glasses 3D glasses communication range ....... 16 Using the 3D glasses ........................... 16 3D Settings 2D-3D Display Sel. (Select) ...............
S Installation .......................................... 39 Operation ............................................ 23 Picture ................................................. 25 Screen .................................................. 32 Setup ................................................... 34 Menu Position ......................................... 34 Messages Caution ................................................ 50 Warning ............................................... 50 Motionflow ...........
© 2015 Sony Corporation
