VIDEO PROJECTOR VPL-VW50 PROTOCOL MANUAL 1st Edition
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden.
Table of Contents 1. Introduction 2. RS-232C 2-1. Communication Specifications .......................................... 1 2-2. Command Block Format .................................................... 2 2-3. Block Format ..................................................................... 3 2-4. Connection ......................................................................... 4 2-5. Communication Procedure ................................................ 4 2-5-1. Outline of Communication ....
1. Introduction This protocol manual describes the basic configuration and basic operations of various commands used for projector. Projector can be controlled using the commands provided in “Appendix”. Using an external CONTROLLER , etc., inputs can be switched and the power can also be turned on and off. In the following paragraphs, “CONTROLLER” means an external device such as a PC which controls projector using these commands. 2. RS-232C 2-1.
2-2. Command Block Format The code from B0 to B7 as described below are transmitted.
2-3. Block Format Transmission from the Master side B0 B1 B2 B3 B4 B5 START CODE Start of Command ITEM NUMBER Set the Data Category Value desired. Refer to the Appendix Table 1 for details.
2-4. Connection Communication is enabled by the use of a D-Sub 9 Pin cross (reverse) cable. The pin assignment of D-Sub 9 Pin and D-Sub 25 Pin is as follows.
2-6. Communication Rules . When sending a command from CONTROLLER, the return data from PROJECTOR should be received first before sending the next command. Even if the next command is sent before receiving the return data, since PROJECTOR will not be able to receive that command, it does not return a response to CONTROLLER. Consequently, no error code is also sent. The following lists the approximate waiting times for PROJECTOR to return the return data after CONTROLLER sends the command. .
Appendix
Item Number Upper byte Lower byte Input 00h 01h 00h 02h Data Upper byte Lower byte Video 00h S Video 01h Input A 02h Component 03h HDMI1 04h HDMI2 05h Dynamic 00h Standard 01h Cinema 02h User1 03h User2 04h User3 05h Contrast 00h 10h 00h to 64h (0 to 100) Brightness 00h 11h 00h to 64h (0 to 100) Color 00h 12h 00h to 64h (0 to 100) Hue 00h 13h 00h to 64h (0 to 100) Sharpness 00h 14h Normal 00h to 64h (0 to 100) ColTemp 00h Item Number Item Upper byte Lower byte Data Wide Mode 00h 20h Full Gamma Correction 00h Remarks Data 22h Upper byte Lower byte 00h Normal 01h Wide Zoom 02h Zoom 03h Full1 07h Full2 08h Off 00h Gamma 1 01h Gamma 2 02h Gamma 3 03h 00h Over Scan 00h 23h Off On 01h Screen Area 00h 24h Full 00h Through 01h Off 00h NR Picture Muting Input-A Signal Sel 00h 00h 00h 25h 30h 32h Low 01h Middle 02h High 03h Off 00h On 01h Auto 00h Item Number Data Item Upper byte Lower byte Data Status Error 01h 01h NO ERROR Status Power 01h Remarks 02h Upper byte Lower byte 00h LAMP ERROR 01h FAN ERROR 02h COVER ERROR 04h TEMP ERROR 08h D5V ERROR 10h POWER ERROR 20h WARNING ERROR 40h NVM Data ERROR 80h STANBY 00h Get only START UP 01h STARTUP LAMP 02h POWER ON 03h COOLING1 04h COOLING2 05h SAVING COOLING1 06h SAVING COOLING2 07h SAVING STABY 08h 0000h-FFFFh *1 Lamp Timer 01h Item Number Item Data Data Upper byte Lower byte ACK _ 00h 00h NAK Undefined Command 01h 01h Size Error 04h Select Error 05h Range Over 06h Not Applicable 0Ah Check Sum Error F0h 10h Framing Error 20h Parity Error 30h Over Rub Error 40h Other Comm Error 50h Waiting time for the return value is about 200 msec. n This waiting time for the return value is subject to the conditions that communication is not bothered by any reasons.10 VPL-VW50 x3 LENS SHIFT ↑ LENS SHIFT ↓ 7x 6x 5x 4x 3x 2x 1x 0x APA x0 PICTURE MODE STANDARD LENS ZOOM DOT PHASE x2 PICTURE MODE DYNAMIC x1 <20BIT CATEGORY> LENS SHIFT PICTURE MODE CINEMA x3 *1 Sent the command twice for [low] the standby mode.
The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation. Le matériel contenu dans ce manuel consiste en informations qui sont la propriété de Sony Corporation.
VPL-VW50 (SY) E 9-883-615-01 Sony EMCS Corporation Ichinomiya Tec English 2006IR16-1 ©2006
