4-135-541-11 (1) Data Projector Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference.
WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. WARNING THIS APPARATUS MUST BE EARTHED. IMPORTANT The nameplate is located on the bottom. WARNING When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit.
Plug Cap Parallel blade with ground pin (NEMA 5-15P Configuration) Cord Type SJT, three 16 or 18 AWG wires Length Minimum 1.5m (4 ft .11in.), Less than 4.5 m (14 ft .9 5/8 in.) Rating Minimum 10A, 125V Using this unit at a voltage other than 120V may require the use of a different line cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel. WARNING: THIS WARNING IS APPLICABLE FOR OTHER COUNTRIES. 1.
Table of Contents Precautions ......................................... 5 Notes on Installation and Usage ........ 6 Overview Features .............................................. 9 Location and Function of Controls .. 10 Top/Right Side/Front .................. 10 Rear/Bottom ............................... 10 Control Panel .............................. 12 Connector Panel ......................... 14 Remote Commander ................... 15 About the Preset Memory No. ....32 The SET SETTING Menu .......
Precautions Safety • Check that the operating voltage of your unit is identical with the voltage of your local power supply. If voltage adaptation is required, consult with qualified Sony personnel. • Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it further. • Unplug the unit from the wall outlet if it is not to be used for several days. • To disconnect the cord, pull it out by the plug. Never pull the cord itself.
• If you rub on the cabinet with a stained cloth, the cabinet may be scratched. • If the cabinet is in contact with a rubber or vinyl resin product for a long period of time, the finish of the cabinet may deteriorate or the coating may come off. Notes on Installation and Usage Unsuitable Installation LCD data projector This LCD data projector is manufactured using high-precision technology.
Hot and humid Very dusty, extremely smoky locations • Avoid installing the unit in a location where the temperature or humidity is very high, or the temperature is very low. • To avoid moisture condensation, do not install the unit in a location where the temperature may rise rapidly. Avoid installing the unit in a very dusty or extremely smoky environment. Otherwise, the air filter will become obstructed, and this may cause a malfunction of the unit or damage it.
Do not block the ventilation holes Usage at High Altitude When using the projector at an altitude of 1,500 m or higher, turn on “High Altitude Mode” in the INSTALL SETTING menu. Failing to set this mode when using the projector at high altitudes could have adverse effects, such as reducing the reliability of certain components. Avoid using a thick-piled carpet or anything that covers the ventilation holes (exhaust/ intake); otherwise, internal heat may build up.
B Overview Features High brightness · High picture performance High picture performance VPL-EX70/EX7:Three super-high-aperture 0.63-inch XGA panels with approximately 790,000 effective pixels produce a resolution of 1024 × 768 dots (horizontal/vertical) for RGB input, and 750 horizontal TV lines for video input. VPL-ES7:Three super-high-aperture 0.
Location and Function of Controls Top/Right Side/Front 4 1 2 5 3 6 Rear/Bottom qa 7 10 8 Location and Function of Controls qs qd 9 0 qf qg qh
a Ventilation holes (exhaust) b Lens Remove the lens cover before projection. d Control panel For details, see “Control Panel” on page 12. e Zoom ring Adjusts the picture size. f Focus ring Adjusts the picture focus. g Ventilation holes (intake)/Air filter cover h Adjusters (fore pad) i Lamp cover Security bar Overview c Front remote control detector p Security lock Connects to an optional security cable (from Kensington). Web page address: http://www.kensington.
Control Panel 1 2 3 a ?/1 (On/Standby) key Turns on the projector when the projector is in standby mode. To turn off the power, press the ?/1 key twice according to the message or hold the ?/1 key for about one second. Lights up or flashes under the following conditions: – Lights in red when the AC power cord is plugged into a wall outlet. Once the projector is in standby mode, you can turn it on with the ?/1 key.
For detail, see page 45. e MENU key Displays the on-screen menu. Press again to clear the menu. Overview f PIC MUTING key Cuts off the picture. Press again to restore the picture.
Connector Panel VPL-EX70 1 2 3 VPL-EX7 1 2 3 VPL-ES7 1 3 a VIDEO IN connector • S VIDEO (mini DIN 4-pin): Connects to the S video output of video equipment. • VIDEO (phone type): Connects to the video output of video equipment. b AUDIO INPUT connector Inputs audio signal attached to the image from INPUT A, INPUT B (VPL-EX70 only) or VIDEO.
d INPUT B connector Remote Commander The keys that have the same names as those on the control panel function identically. 9 1 e OUTPUT connector • MONITOR (HD D-sub 15-pin female): Connects to the input connector of the monitor. Only the computer signal on the current channel is output from among the signals connected to INPUT A or INPUT B (VPL-EX70 only). • AUDIO (stereo minijack): Connects to the active speaker. Adjust the volume with VOLUME +/– on the remote commander.
k USB key This function is not provided in this projector. l APA (Auto Pixel Alignment) key Automatically adjusts a picture to its clearest while a signal is input from a computer. For details, see “Smart APA” in “The SET SETTING Menu” on page 33. m LENS key 2 Install the lithium battery. This function is not provided in this projector. n KEYSTONE (Trapezoidal distortion correction) /TILT key Adjusts the vertical trapezoidal distortion of the image.
B Projecting the Picture Installing the Projector The distance between the lens and the screen varies depending on the size of the screen. Use the following table as a guide. Screen Projecting the Picture Distance between the screen and the center of the lens * Adjuster not stretched, and the V Keystone function has been done. Unit: m (feet) Projected image size (diagonal) (inches) 40 80 100 150 200 250 300 Minimum Distance 1.1 (3.6) 2.3 (7.5) 2.9 (9.5) 4.4 (14.4) 5.8 (19.0) 7.3 (24.
Connecting the Projector To connect a computer Rear side VPL-EX70 When you connect the projector, make sure to: • Turn off all equipment before making any connections. • Use the proper cables for each connection. • Insert the cable plugs firmly; loose connections may increase noise and reduce performance of picture signals. When pulling out a cable, be sure to pull it out by the plug, not the cable itself. Connecting a Computer This section describes how to connect the projector to a computer.
appear properly. Set your computer to output the signal to only the external monitor. For details, refer to the operating instructions supplied with your computer. Note To connect a Macintosh computer equipped with a video output connector of a type having two rows of pins, use a commercially available plug adaptor. 1 Stereo audio connecting cable (not supplied) (Use a no-resistance cable.
4 Projecting Press the INPUT key to select the input source.
For VPL-EX70 F7 or Fx and Fn Note The key used for switching the computer to output to the projector varies depending on the type of computer. 6 Adjust the upper or lower position of the picture. Use the adjuster to adjust the picture position. Using the adjuster Lift the projector while pressing the adjuster adjustment button, and adjust the tilt of the projector, then release the button to lock the adjuster. 8 Adjust the size of the picture and the focus.
Turning Off the Power 1 Press the ?/1 key. “POWER OFF? Please press ?/1 key again.” appears to confirm that you want to turn off the power. Note The message disappears if you press any key other than the ?/1 key, or if you do not press any key for five seconds. 2 Press the ?/1 key again. The ?/1 key flashes in green and the fan continues to run to reduce the internal heat. Also, the ?/1 key flashes quickly for the first 60 seconds.
B Convenient Functions The menu currently selected is shown as a yellow button. Selecting the Menu Language You can select one of seventeen languages for displaying the menu and other on-screen displays. The factory setting is English. To change the menu language, proceed as follows: 1,2 4 Press the v or V key to select the MENU SETTING menu, then press the B or ENTER key. The selected menu appears. Convenient Functions 5 Press the v or V key to select “Language,” then press the B or ENTER key.
Enter the password on this screen. Security Lock Enter new password key. The projector is equipped with a security lock function. When you turn the power of the projector on, you are required to input the previously set password. If you do not input the correct password, you will not be able to project the picture. Notes • You will not be able to use the projector if you forget your password and the password administrator is not available.
2 Enter the password. Enter the password that was set. Other Functions Note If you call the customer service center because you have forgotten the password, you will need to be able to verify the projector’s serial number and your identity. (This process may differ in other countries/regions.) Once your identity has been confirmed, we will provide you with the password.
2 Move the icon to the point on the image you want to enlarge. Use the arrow key (v/V/b/B) to move the icon. 3 Press the D ZOOM + key again. The portion of the image where the icon is located is enlarged. The enlargement ratio is displayed on the screen for a few seconds. By pressing the + key repeatedly, the image size (ratio of enlargement: max. 4 times) increases. Use the arrow key (v/V/b/B) to scroll the enlarged image. To return the image to its original size Press the D ZOOM – key.
B Adjustments and Settings Using a Menu 2 Using a MENU Use the v or V key to select a menu, then press the B or ENTER key. The selected menu appears. The projector is equipped with an on-screen menu for making various adjustments and settings. 3 Select an item. Use the v or V key to select the item, then press the B or ENTER key. The setting items are displayed in a popup menu or in a sub menu.
To clear the menu Press the MENU key. The menu disappears automatically if a key is not pressed for one minute. To reset items that have been adjusted Select the item that you want to reset, and then press the RESET key on the Remote Commander. “Complete!” appears on the screen and the setting of the item that you have selected is reset to its factory preset value. Items that can be reset are: • “Contrast,” “Brightness,” “Color,” “Hue” and “Sharpness” on the “Adjust Picture...
The PICTURE SETTING Menu The PICTURE SETTING menu is used for adjusting the picture or volume. Items that can be adjusted or set depend on the kind of input signals. For details, see “Input signals and adjustable/setting items” on page 39. PICTURE SETTING Input A Picture Mode Adjust Picture... S t a n d a rd Vo l u m e : 30 PICTURE SETTING ADJUST PICTURE Contrast: Brightness: Gamma Mode: C o l o r Te m p .
Setting items Color Temp. Functions Initial setting Adjusts the color temperature. • High: Makes white colors bluish. • Middle: Makes white part of the picture natural white. • Low: Makes white colors reddish. Set according to the input signal DDE (Dynamic Selects the mode to play the input video signal Film according to the material. Detail • Off: Plays back the interlace format without Enhancer) conversion. • Progressive: Plays back the video picture of the interlace format converting to progressive.
The INPUT SETTING Menu The INPUT SETTING menu is used to adjust the input signal. When the signal is input from a computer Setting items Functions Initial setting Dot Phase Adjusts the dot phase of the LCD panel and the signal output from a computer. Adjust the picture further for finer picture after the picture is adjusted by pressing the APA key. Set according to the input signal H Size Adjusts the horizontal size of a picture output from a computer.
Setting items Functions Aspect (When the PC signal is input) You can set the aspect ratio of the picture to be Set according to displayed for the current input signal. This item is the input signal enabled only when an PC signal (preset memory numbers 21 to 63) is input. • Full 1: Displays a picture vertically or horizontally to fill the screen without changing the aspect ratio of the original picture. • Full 2: The original image is projected fully in the window.
The SET SETTING Menu The SET SETTING menu is used for changing the settings of the projector. SET SETTING S m a r t A PA : Auto Input Search: Input-A Signal Sel.: Color System: Pow e r S av i n g : Pa n e l Key L o ck : C C D i s p l ay : Lamp Timer Reset Input-A On Off Au t o Au t o Off Off Off Functions Initial setting Smart APA The APA (Auto Pixel Alignment) automatically On adjusts “Dot Phase,” “H Size” and “Shift” on the INPUT SETTING menu for the input signal from a computer.
Setting items Functions Power Saving Selects the Power Saving mode. Off • Lamp off: The lamp goes off if no signal is input for 10 minutes. The lamp lights again when a signal is input or any key is pressed. • Standby: The projector goes into Standby mode if no signal is input for 10 minutes. To use it, turn on the power again. • Off: The projector does not go into Power Saving mode.
The MENU SETTING Menu The MENU SETTING menu is used for changing the menu displays. Functions Initial setting Status (on-screen display) Sets up the on-screen display. When set to “Off,” turns off the on-screen displays except for the menus, a message when the power is turned off, and warning messages. On Language Selects the language used in the menu and on-screen displays.
The INSTALL SETTING Menu The INSTALL SETTING menu is used for changing the settings of the projector. INSTALL SETTING Input-A V Key s t o n e : Au t o I m ag e F l i p : Off B a ck g ro u n d : Blue Lamp Mode: S t a n d a rd High Altitude Mode: O f f S e c u r i t y L o ck : Off D i r e c t Pow e r O n : O f f Setting items Functions V Keystone (VPL-EX70 only) Corrects the trapezoidal distortion caused by the projection Auto angle.
Notes • The picture quality may deteriorate when the V Keystone function is used, because it is an electrical correction. • If you set “High Altitude Mode” to “On” at an altitude of under 1,500 m, the reliability of the lamp may be reduced. Notes on VPL-EX70 • The auto V Keystone adjustment may not correct the trapezoidal distortion perfectly, depending on the room temperature or the screen angle.
The INFORMATION Menu The INFORMATION menu displays the model name, serial number, the horizontal and vertical frequencies of the input signal and the cumulated hours of usage of the lamp. Model name INFORMATION VPL-EX70 fH: fV: Lamp Timer: Input A Serial No. 3 3 3 3 3 3 3 48,47kHz 60,00Hz No.23 1024x768 2 H Serial number Memory number of an input signal Signal type Setting items Functions fH Displays the horizontal frequency of the input signal. The displayed value is approximate.
Input signals and adjustable/setting items Some of the items in the menus cannot be adjusted depending on the input signal as indicated in the following tables. The items that cannot be adjusted are not displayed in the menu. PICTURE SETTING menu Item Input signal Video or S-Video (Y/ C) Component Video GBR Computer z z z z Contrast z z z z Brightness z z z z Color z Picture Mode Adjust Picture... Hue z (NTSC 3.58/4.
B Maintenance Replacing the Lamp The lamp used as a light source is consumable product. Thus replace the lamp with a new one in the following cases. • When the lamp has burnt out or dims • “Please replace the Lamp.” appears on the screen • The LAMP/COVER indicator lights up (repeats flashing three times) The lamp life varies depending on conditions of use. Use an LMP-E191 Projector Lamp as the replacement lamp. Use of any other lamps than the LMP-E191 may cause damage to the projector.
5 Insert the new lamp all the way in until it is securely in place (a). Tighten the two screws (b). Fold down the handle to replace it (c). 11Select “Lamp Timer Reset”, and then press the ENTER key. SET SETTING Input-A S m a r t A PA : Auto Input Search: Input-A Signal Sel.: Color System: Pow e r S av i n g : Pa n e l Key L o ck : C C D i s p l ay : Lamp Timer Reset On Off Au t o Au t o Off Off Off 12Select “Execute” with the V key, and then press the ENTER key.
Cleaning the Air Filter Notes The air filter should be cleaned whenever you replace the lamp. Remove the air filter, and then remove the dust with a vacuum cleaner. The time needed to clean the air filter will vary depending on the environment or how the projector is used. When it becomes difficult to remove the dust from the filter with a vacuum cleaner, remove the air filter and wash it. 1 Turn the power off and unplug the power cord. 2 Draw out the air filter cover and remove it.
B Others Troubleshooting If the projector appears to be operating erratically, try to diagnose and correct the problem using the following instructions. If the problem persists, consult with qualified Sony personnel. Power Symptom Cause and Remedy The power is not turned on. • The power has been turned off and on with the ?/1 key at a short interval. c Wait for about 90 seconds before turning on the power (see page 22). • The lamp cover is not secured. c Close the lamp cover securely (see page 41).
Symptom Cause and Remedy On-screen display does not “Status” on the MENU SETTING menu has been set to “Off.” c Set “Status” on the MENU SETTING menu to “On” (see appear. page 35). Color balance is incorrect. • The picture has not been adjusted properly. c Adjust the picture (see page 29). • The projector is set to the wrong color system. c Set “Color System” on the SET SETTING menu to match the color system being input (see page 33). The picture is too dark.
Remote Commander Symptom Cause and Remedy The Remote Commander does not work. The Remote Commander battery are dead. c Replace them with new battery (see page 16). Others Symptom Cause and Remedy The control panel keys do not function. The control panel keys are locked. c Unlock the control panel keys (see page 34). Indicators Symptom Cause and Remedy The lamp cover or the air filter cover is detached. The LAMP/COVER indicator flashes in orange. c Attach the cover securely (see pages 41 and 42).
Caution Messages Use the list below to check the meaning of the messages displayed on the screen. Message Meaning and Remedy Not applicable! You have pressed the wrong key. c Press the appropriate key. The panel keys are locked! “Panel Key Lock” on the SET SETTING menu is set to “On.” c All the keys on the control panel of the projector are locked. Operate the projector with the keys on the Remote Commander (see page 34).
Specifications Optical characteristics Projection system 3 LCD panels, 1 lens, projection system LCD panel VPL-EX70/EX7: 0.63-inch XGA panel, about 2,360,000 pixels (1024 × 768 × 3) VPL-ES7: 0.63-inch SVGA panel, about 1,440,000 pixels (800 × 600 × 3) Lens 1.2 times zoom lens f 18.53 to 22.18 mm/F1.65 to 1.93 Lamp 190 W Ultra high pressure lamp Projected picture size 40 to 300 inches Light output 1) VPL-EX70: 2600 lm VPL-EX7/ES7: 2000 lm 1) When the Lamp Mode is set to “High.
R: 0.7 Vp-p ±2 dB (75 ohms terminated) G: 0.7 Vp-p ±2 dB (75 ohms terminated) B: 0.
RS-232C connector (D-sub 9 pin, female) (VPL-EX70/EX7 only) Pin assignment INPUT A connector (HD D-sub 15-pin, female) 1 R/R-Y 9 2 3 G/Y B/B-Y 10 11 Power supply input for DDC GND GND 4 5 6 7 8 RESERVE GND GND (R) GND (G) GND (B) 12 13 14 15 DDC/SDA HD VD DDC/SCL 1 2 3 4 NC RXDA TXDA DTR 5 GND 6 7 8 9 NC RTS CTS NC INPUT B connector (HD D-sub 15-pin, female) (VPL-EX70 only) R 9 2 3 4 5 6 7 8 G B RESERVE GND GND (R) GND (G) GND (B) 10 11 12 13 14 15 Power supply input for DDC GND GND
Preset signals Memory Preset signal No. 15.734 59.940 Sync Video 60 Hz 2 Video 50 Hz 50 Hz 15.625 50.000 – 3 480/60i 480/60i 15.734 59.940 S on G/Y 4 575/50i 575/50i 15.625 50.000 S on G/Y 5 480/60p 480/60p (Progressive component NTSC) 31.470 60.000 S on G/Y 6 575/50p 575/50p (Progressive component PAL) 31.250 50.000 S on G/Y 7 1080/60i 1035/60i, 1080/60i 33.750 60.000 S on G/Y 8 1080/50i 1080/50i 28.130 50.000 S on G/Y 10 720/60p 720/60p 45.000 60.
Memory Preset signal No. 45 1280 × 960 46 47 1280 × 1024 48 49 fH (kHz) fV (Hz) Sync SXGA VESA 60 Hz 60.000 60.000 H-pos, V-pos SXGA VESA 75 Hz 75.000 75.000 H-pos, V-pos SXGA VESA 60 Hz 63.974 60.013 H-pos, V-pos SXGA VESA 75 Hz 79.976 75.025 H-pos, V-pos SXGA VESA 85 Hz 91.146 85.024 H-pos, V-pos 50 1400 × 1050 SXGA+ 60 Hz 65.317 59.978 H-neg, V-pos 55 1280 × 768 WXGA 60Hz 47.776 59.870 H-neg, V-pos 56 1280 × 720 WXGA 60Hz 44.772 59.
Installation Diagram Floor Installation (Front Projection) Distance between the front of the cabinet and the center of the lens Foremost part of the cabinet Wall Center of the lens 14.6 (19/32) Center of the lens Center of the screen Floor * Adjuster not stretched, and the V Keystone function has been done. Unit: mm (inches) This section describes the examples of installing the projector on a desk, etc. See the chart on page 53 concerning the installation measurements.
Unit: mm (inches) PS a 40 N 60 1180 1780 (46 1/2) (70 1/8) M 1330 2020 (52 3/8) (79 5/8) 80 100 120 150 2390 (94 1/8) 2990 (117 3/4) 3600 (141 3/4) 2700 (106 3/8) 3380 (133 1/8) 4070 (160 3/8) 180 200 250 300 4510 5410 (177 5/8) (213 1/8) 6020 (237 1/8) 7530 (296 1/2) 9050 (356 3/8) 5090 (200 1/2) 6800 (267 3/4) 8500 (334 3/4) 10210 (402 1/8) 6110 (240 5/8) b Based on the calculation formula given below. c Based on the calculation formula given below. a (N) = {(PS × 29.
Ceiling Installation (Front Projection) 69.5 (2 3/4) 104.5 (4 1/8) 42.2 (1 5/8) The unit is set so that the bottom is parallel to the ceiling. The V Keystone function has been done. Center of the screen Center of the lens Center of the Projector Holes for mounting a projector suspension support Ceiling Center of the lens Center of the screen Foremost part of the cabinet Hole for mounting a projector suspension support (front) 72.5 (2 7/8) 10.4 (3/8) 26.
Unit: mm (inches) PS 40 60 80 100 120 150 180 200 250 300 a’ N 1200 (47 1/4) 1800 (70 7/8) 2410 (95) 3010 (118 5/8) 3620 (142 5/8) 4530 (178 3/8) 5440 (214 1/4) 6040 (237 7/8) 7560 (297 3/4) 9070 (357 1/4) 2040 (80 3/8) 2720 (107 1/8) 3410 (134 3/8) 4090 (161 1/8) 5120 (201 5/8) 6140 (241 7/8) 6830 (269) 8540 (336 3/8) 10250 (403 5/8) M 1350 (53 1/4) x Based on the calculation formula given below. b Free a’(N) = {(PS × 29.415) × 1.03} - 32.0 + 16.4 a’(M) = {(PS × 35.
Dimensions Front 314 (12 3/8) 109 (4 3/8) 72.2 (2 7/8) 69.
269 (10 5/8) Top 314 (12 3/8) Unit: mm (inches) Others Dimensions 57
Index A Adjust Picture .......................................... 29 Air filter ................................................... 42 Aspect ............................................... 31, 32 Auto Input Search ................................... 33 B Background ............................................. 36 Batteries .................................................. 16 Brightness ............................................... 29 C CC Display ..............................................
Reset resetting an item ..................................28 RS-232C connector .................................49 S Screen size ...............................................17 Security bar .............................................11 Security Lock ....................................24, 36 Security lock ............................................11 Sharpness .................................................29 Shift .........................................................31 Smart APA ...............
Sony Corporation
