F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\01COV.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\02REG.fm WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. WARNING THIS APPARATUS MUST BE EARTHED. IMPORTANT The nameplate is located on the bottom. WARNING This unit has no power switch.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\02REG.fm DO NOT USE ANY OTHER POWER CORD. Plug Cap Parallel blade with ground pin (NEMA 5-15P Configuration) Cord Type SJT, three 16 or 18 AWG wires Length Minimum 1.5m (4 ft .11in.), Less than 2.5 m (8 ft .3 in.) Rating Minimum 10A, 125V Using this unit at a voltage other than 120V may require the use of a different line cord or attachment plug, or both.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\01COVTOC.fm masterpage: Left Table of Contents Overview Precautions ......................................... 5 Notes on Installation and Usage ........ 6 Unsuitable Installation ................. 6 Unsuitable Conditions .................. 7 Usage at High Altitude ................. 7 About the Supplied Manuals .............. 8 Features .............................................. 8 Location and Function of Controls ....
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\03INT.fm masterpage: Right B Overview Precautions Safety Illumination • To obtain the best picture, the front of the screen should not be exposed to direct lighting or sunlight. • Ceiling-mounted spot lighting is recommended. Use a cover over fluorescent lamps to avoid lowering the contrast ratio. • Cover any windows that face the screen with opaque draperies.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\03INT.fm Notes on Installation and Usage masterpage: Left Hot and humid Unsuitable Installation Do not install the projector in the following situations. Installation is these situations or locations may cause a malfunction or damage to the unit. Poorly ventilated locations • Avoid installing the unit in a location where the temperature or humidity is very high, or the temperature is very low.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\03INT.fm Very dusty, extremely smoky locations Blocking the ventilation holes Overview Avoid installing the unit in a very dusty or extremely smoky environment. Otherwise, the air filter will become obstructed, and this may cause a malfunction of the unit or damage it. Dust preventing the air passing through the filter may cause a rise in the internal temperature of the unit. Clean the filter periodically.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\02C01.fm About the Supplied Manuals The following manuals are supplied with this unit. Safety Regulations (separately printed manual) This manual describes important notes and cautions to which you have to pay attention when handling and using this product. Quick Reference Manual (separately printed manual) This manual describes basic operations for projecting pictures after you have made the required connections.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\02C01.fm you to move the projector to another location immediately after turning it off. Versatile installation capability Direct Power On/Off function The AC power of the entire system can be directly turned on/off with a breaker or other switch without pressing the power key on the projector.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\02C01.fm g Speaker Control Panel h Rear remote control detector i Ventilation holes (intake) j Adjusters (hind pad) Turn the appropriate adjuster to the right or left for minor tilt adjustment of the projected picture. VPL-CX63 k Ventilation holes (intake)/Lamp cover l Ventilation holes (intake)/Air filter cover Notes • Do not place anything near the ventilation holes as this may cause internal heat build-up.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\02C01.fm The fan runs for about 60 seconds after the power is turned off. masterpage: Right Connector Panel For details, see page 19. c INPUT key Overview d MENU key Displays the on-screen menu. Press again to clear the menu. e ENTER/f/F/g/G (Arrow) keys Used to enter the settings of items in the menu system, select a menu, or make various adjustments. f FOCUS +/– keys Adjusts the picture focus.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\02C01.fm c AUDIO jack (stereo minijack) (common INPUT A/B) To listen to sound output from a computer, connect via this jack to the audio output of the computer. d VIDEO IN (Video input) connector Connects to external video equipment such as a VCR. • S VIDEO (mini DIN 4-pin): Connects to the S video output (Y/C video output) of video equipment.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\02C01.fm g FREEZE key 2 Install the lithium battery. Freezes the projected picture. To cancel the frozen picture, press the key again. h PIC MUTING key i D ZOOM (Digital Zoom) +/– key Enlarges the image at a desired location on the screen. Face the + side up. Overview Cuts off the picture. Press again to restore the picture.
masterpage: Left.L0 F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\03C02.fm B Projecting the Picture Installing the Projector The distance between the lens and the screen varies depending on the size of the screen. Use the following table as a guide. Screen Distance between the screen and the center of the lens Unit: m (feet) Screen size (inches) 40 60 80 100 120 150 180 200 250 300 Minimum Distance 1.2 (3.9) 1.8 (5.9) 2.4 (7.9) 3.0 (9.8) Maximum Distance 1.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\03C02.fm Connecting the Projector To connect a computer Right side When you connect the projector, make sure to: Projecting the Picture • Turn off all equipment before making any connections. • Use the proper cables for each connection. • Insert the cable plugs firmly; loose connections may increase noise and reduce performance of picture signals.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\03C02.fm For details, refer to the operating instructions supplied with your computer. B Video cable (not supplied) or S-Video cable (not supplied) To connect to a video GBR/ Component output connector Note To connect a Macintosh computer equipped with a video output connector of a type having two rows of pins, use a commercially available plug adaptor.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\03C02.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\03C02.fm F7 or displays on the screen, and adjust the value with the v/V/b/B keys. The corrected value is effective until the power is turned off. • Be careful not to let the projector down on your fingers. • Do not push hard on the top of the projector with the adjuster extended. It may cause a malfunction. Fx and Fn Note The key used for switching the computer to output to the projector varies depending on the type of computer.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\03C02.fm masterpage: Right Turning Off the Power 1 Press the ?/1 key. “POWER OFF? Please press ?/1 key again.” appears to confirm that you want to turn off the power. Note 2 Projecting the Picture The message disappears if you press any key other than the ?/1 key, or if you do not press any key for five seconds. Press the ?/1 key again.
masterpage: Left.L0 F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\04C03.fm B Convenient Functions Selecting the Menu Language You can select one of fifteen languages for displaying the menu and other on-screen displays. The factory setting is English. To change the menu language, proceed as follows: 4 Press the v or V key to select the MENU SETTING menu, then press the B or ENTER key. The selected menu appears.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\04C03.fm Security Lock The projector is equipped with a security lock function. When you turn the power of the projector on, you are required to input the previously set password. If you do not input the correct password, you will not be able to project the picture. Enter new password key. Power-on cannot be performed without the password. Use: 3 Cancel: Other key Enter the password again to confirm.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\04C03.fm The security lock is set to on, then it becomes effective. The screen used for entering the password is displayed when the power is turned on the next time. Security certification When the password screen is displayed, enter the password that was set. If you fail to enter the correct password after three tries, the projector cannot be used. In this case, press the ?/1 key to turn off the power.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\04C03.fm masterpage: Right Effective Tools for Your Presentation To enlarge the image (Digital Zoom function) You can select a section of the image to enlarge. This function works when a signal from a computer is input. This function does not work when a video signal is input. 1 Project a normal image, and press the D ZOOM + key on the Remote Commander. The digital zoom icon appears in the center of the image.
masterpage: Left.L0 F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\05C04.fm B Adjustments and Settings Using a Menu Using a MENU 3 Select an item. Use the v or V key to select the item, then press the B or ENTER key. The setting items are displayed in a popup menu or in a sub menu. The projector is equipped with an on-screen menu for making various adjustments and settings.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\05C04.fm masterpage: Right To clear the menu Press the MENU key. The menu disappears automatically if a key is not pressed for one minute. To reset items that have been adjusted Select the item that you want to reset, and then pres the RESET key on the Remote Commander. “Complete!” appears on the screen and the setting of the item that you have selected is reset to its factory preset value.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\05C04.fm The PICTURE SETTING Menu The PICTURE SETTING menu is used for adjusting the picture or volume. Items that can be adjusted or set depend on the kind of input signals. For details, see “Input signals and adjustable/setting items” on page 35. PICTURE SETTING S t a n d a rd Vo l u m e : 30 PICTURE SETTING ADJUST PICTURE Contrast: Brightness: Gamma Mode: C o l o r Te m p .
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\05C04.fm The INPUT SETTING Menu The INPUT SETTING menu is used to adjust the input signal. Items that can be adjusted or set depend on the kind of input signals. For details, see “Input signals and adjustable/setting items” on page 35. When the video signal is input Functions Initial setting Wide Mode Sets the aspect ratio of the picture. Off • Off: When a picture with a ratio of 4:3 is input.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\05C04.fm Setting items Shift Scan Converter Functions Initial setting Set according to Adjusts the position of the picture. H adjusts the horizontal position of the picture.V adjusts the vertical the input signal position of the picture. As the setting for H increases, the picture moves to the right, and as the setting decreases, the picture moves to the left.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\05C04.fm The SET SETTING Menu The SET SETTING menu is used for changing the settings of the projector. Functions Smart APA The APA (Auto Pixel Alignment) automatically On adjusts “Dot Phase,” “H Size” and “Shift” on the INPUT SETTING menu for the input signal from a computer. • On: When a signal is input from a computer, the APA functions automatically so that the picture can be seen clearly.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\05C04.fm Setting items Functions Standby Mode You can lower the power consumption in standby Standard mode. • Standard: Normally, select this position. • Low: Select this position when you want to lower the power consumption in standby mode. Initial setting Power Saving When set to “On,” the projector goes into power saving Off mode if no signal is input for 10 minutes.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\05C04.fm The MENU SETTING Menu The MENU SETTING menu is used for changing the menu displays. Functions Initial setting Status (on-screen display) Sets up the on-screen display. When set to “Off,” turns off the on-screen displays except for the menus, a message when the power is turned off, and warning messages. On Language Selects the language used in the menu and on-screen displays.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\05C04.fm The INSTALL SETTING Menu The INSTALL SETTING menu is used for changing the settings of the projector. Setting items Functions V Keystone Corrects the trapezoidal distortion caused by the projection Auto angle. Select “Auto” for automatic correction, or “Manual” for manual correction using the v/V/b/B keys on the Remote Commander. When the bottom of the trapezoid is longer than the top : Sets a lower value.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\05C04.fm Setting items Functions Initial setting Security Lock Turns on the projector’s security lock function. When set to “On,” turns on the security lock function, which locks the projector once a password has been set. For details, see “Security Lock” on page 21.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\05C04.fm masterpage: Left The INFORMATION Menu The INFORMATION menu displays the model name, serial number, the horizontal and vertical frequencies of the input signal and the cumulated hours of usage of the lamp. Model name INFORMATION VPL-CX63 fH: fV: Lamp Timer: Input A Serial No. 3 3 3 3 3 3 3 48.47kHz 60.00Hz No.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\05C04.fm Input signals and adjustable/setting items Adjust Picture... menu Item Input signal Video or S-Video (Y/C) Component Video GBR Computer B&W z z z z z Contrast z z z z z Brightness z z z z z Color z z z – – z z z – – z Picture Mode Adjust Picture... Hue (NTSC 3.58/4.43 only) Sharpness z z z – Gamma Mode – – z*1 z – Color Temp.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\06C05.fm masterpage: Left.L0 B Maintenance projector over so you can see its underside. Replacing the Lamp The lamp used as a light source is a consumable product. Thus replace this lamp with a new one in the following cases. • When the lamp has burnt out or dims • “Please replace the Lamp.” appears on the screen • The LAMP/COVER indicator lights up The lamp life varies depending on conditions of use.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\06C05.fm 6 Close the lamp cover and tighten the screw. Note Be sure to attach the lamp cover securely as it was. If not, the projector cannot be turned on. Handle 7 Turn the projector back over. 8 Connect the power cord. The ON/STANDBY indicator around the ?/1 key lights in red. 9 5 Insert the new lamp all the way in until it is securely in place (a). Tighten the two screws (b).
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\06C05.fm Cleaning the Air Filter 4 masterpage: Left Remove the air filter. Claws The air filter should be cleaned every 1000 hours. Remove dust from the outside of the ventilation holes with a vacuum cleaner. 1000 hours are approximate. This value varies depending on the environment or how the projector is used. 5 Wash the air filter with a mild detergent solution and dry it in a shaded place.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm masterpage: Right.L0 B Others Troubleshooting If the projector appears to be operating erratically, try to diagnose and correct the problem using the following instructions. If the problem persists, consult with qualified Sony personnel. Power Symptom Cause and Remedy The power is not turned on. • The power has been turned off and on with the ?/1 key at a short interval.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm masterpage: Left Symptom Cause and Remedy “Please check Input-A Signal Sel.” appears in spite of inputting the correct signal from INPUT A. The setting of “Input-A Signal Sel.” on the SET SETTING menu is incorrect. c Select “Computer,” “Video GBR” or “Component” correctly according to the input signal (see page 29). On-screen display does not “Status” on the MENU SETTING menu has been set to “Off.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm Sound Symptom Cause and Remedy No sound. • A cable is disconnected or the connections are wrong. c Check that the proper connections have been made (see page 15). • The audio connecting cable used is incorrect. c Use a no-resistance stereo audio cable (see page 15). • The sound is muted. c Press the AUDIO MUTING key to release audio muting (see page 13). • The sound is not adjusted properly.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm Symptom Cause and Remedy The TEMP/FAN indicator lights up. • The internal temperature is unusually high. c Check to see that nothing is blocking the ventilation holes. • The projector is being used at a high altitude. c Ensure that “High Altitude Mode” on the INSTALL SETTING menu is set to “On.” The electrical system has broken down.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm Caution Messages Use the list below to check the meaning of the messages displayed on the screen. Message Meaning and Remedy Not applicable! You have pressed the wrong key. c Press the appropriate key. The panel keys are locked! “Panel Key Lock” on the SET SETTING menu is set to “On.” c All the keys on the control panel of the projector are locked.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm Specifications Optical characteristics Projection system 3 LCD panels, 1 lens, 3 primary color shutter system LCD panel 0.79-inch XGA panel, about 2,359,296 pixels (786,432 pixels × 3) Lens 1.2 times zoom lens (powered) f=23.5 to 28.2 mm/F1.6 to 1.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm General 328 × 92.6 × 283.8 mm (13 × 3 3/4 × 11 1/4 inches) (w/h/d) (without the projection parts) Mass Approx. 3.7 kg (8 lb 3 oz) Power requirements AC 100 to 240 V, 2.8 to 1.2 A, 50/60 Hz Power consumption Max. 280 W (in standby (standard): 5W in standby (low): 0.5 W) Heat dissipation 921.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm masterpage: Left INPUT B connector (HD D-sub 15-pin, female) 1 R 9 N.C. 2 G 10 GND 3 B 11 GND 4 GND 12 DDC/SDA 5 GND 13 HD/C.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm Preset signals Memory Preset signal No. fH (kHz) fV (Hz) Sync SIZE 1 Video 60 Hz 60 Hz 15.734 59.940 2 Video 50 Hz 50 Hz 15.625 50.000 3 480/60i 480/60i 15.734 59.940 S on G/Y or Composite Sync 4 575/50i 575/50i 15.625 50.000 S on G/Y or Composite Sync 5 1080/60i 1035/60i, 1080/60i 33.750 60.000 S on G/Y 6 640 × 350 VGA mode 1 31.469 70.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm Memory Preset signal No. 32 1280 × 960 33 34*1 1280 × 1024 fH (kHz) fV (Hz) Sync SIZE SXGA VESA 60 Hz 60.000 60.000 H-pos, V-pos 1800 SXGA VESA 75 Hz 75.000 75.000 H-pos, V-pos 1728 SXGA VESA 43 Hz 46.433 86.872 H-pos, V-pos 1696 35 SGI-5 53.316 50.062 S on G 1680 36 SXGA VESA 60 Hz 63.974 60.013 H-pos, V-pos 1696 37 SXGA VESA 75 Hz 79.976 75.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm Warning on power connection Use the supplied power cord when you use the projector in your country/region. Otherwise, use a proper power cord meeting the following specifications.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm Installation Diagram Floor Installation (Front Projection) Distance between the front of the cabinet and the center of the lens Wall Front of the cabinet Front of the lens (11/16) Center of the screen Center of the lens Floor Unit: mm (inches) This section describes the examples of installing the projector on a desk, etc. See the chart on page 51 concerning the installation measurements.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm Ceiling Installation (Front Projection) Center of the lens 104.5 (41/8) 3.7 (5/32) 56.7 (21/4) 81.8 (31/4) Center of the screen 82.2 (31/4) Center of the Projector 46.1 (17/8) 21.4 (27/32) Holes for mounting a projector suspension support Ceiling Center of the lens Front of the cabinet Center of the screen Center of the lens Hole for mounting a projector suspension support (front) 55.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.
masterpage: Left F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm Dimensions Front Center of the projector 81.8 (31/4) 140.5 (55/8) 34.4 (13/8) 61.9 (21/2) Remote control detector PUSH 6 (1/4) 92.6 (33/4) Center of the lens 82.2 (31/4) 245.8 (93/4) 328 (13) Right side 39.5 (19/16) 220.8 (83/4) 36.2 (17/16) 217.3 (85/8) 15 (19/32) Center of the lens 61.9 (21/2) 76.1(3) 17.4 (11/16) 27 23.7 21 ( /32) 15 20.1(13/16) ( /16) 47.1 (17/8) 71.9 (27/8) 57.
masterpage: Right F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\07ADD.fm 5 (7/32) Left side 13 20.3 ( /16) Projector suspension support mounting surface 244 (95/8) Bottom 79.4 (31/4) 94 (33/4) 71.4 (27/8) 56.9 (21/4) 104.5 (41/8) 45 (113/16) 223.7 (87/8) 205.1 (81/8) 195.2 (73/4) 144.3 (53/4) 119.2 (43/4) 240.3 (91/2) 46.1 (17/8) 5.2 (7/32) Others 283.8 (111/4) 56.7 (21/4) 127.7 (51/8) 217.6 (85/8) 24.2 (95/8) 6.8 (9/32) 144.5 (53/4) 81.8 (31/4) 46.
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\01COVIX.fm Index A Adjuster ................................................... 18 Adjusting memory of the settings ........................ 25 the picture ............................................ 26 the picture size/shift ...................... 27, 28 Air filter ................................................... 38 Auto Input Search ................................... 29 B Background .............................................
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\01COVIX.fm masterpage: Right rear remote control detector .................10 Reset resettable items ....................................25 resetting an item ..................................25 S Scan Converter ........................................28 Screen size .........................................14, 44 Security Lock ..........................................33 Sharpness .................................................
F:\Nouhin_NAGANO_E\0403N_VPLCX63_OM_CDROM\0403N_2684389111VPLCX63GB_OM\08BCO.