VIDEO PROJECTOR VPL-BW5 VPL-BW7 PROTOCOL MANUAL 1st Edition (Revised 1)
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden.
Table of Contents 1. Introduction 2. RS-232C 2-1. Communication Specifications .......................................... 1 2-2. Command Block Format .................................................... 2 2-3. Block Format ..................................................................... 3 2-4. Connection ......................................................................... 4 2-5. Communication Procedure ................................................ 4 2-5-1. Outline of Communication .
1. Introduction This protocol manual describes the basic configuration and basic operations of various commands used for projector. Projector can be controlled using the commands provided in “Appendix”. Using an external CONTROLLER , etc., inputs can be switched and the power can also be turned on and off. In the following paragraphs, “CONTROLLER” means an external device such as a PC which controls projector using these commands. 2. RS-232C 2-1.
2-2. Command Block Format The code from B0 to B7 as described below are transmitted.
2-3. Block Format Transmission from the Master side B0 B1 B2 B3 B4 B5 START CODE ITEM NUMBER SET / GET DATA B6 CHECK SUM B7 END CODE Reception in the Master side B0 B1 B2 B3 B4 B5 ACK DUMMY DATA Reception in the Master side (With Data) B4 B5 START CODE ITEM NUMBER REPLY DATA B6 CHECK SUM B7 END CODE VPL-BW5 SET: Data to be set (Refer to the Appendix Table 2) GET: Unused. Set Dummy data [0 x 00, 0 x 00] Check Sum End of Command Receive results of the data transmission from the Projector.
2-4. Connection Communication is enabled by the use of a D-Sub 9 Pin cross (reverse) cable. The pin assignment of D-Sub 9 Pin and D-Sub 25 Pin is as follows.
2-6. Communication Rules . When sending a command from CONTROLLER, the return Data from PROJECTOR should be received first before sending the next command. Even if the next command is sent before receiving the return Data, since PROJECTOR will not be able to receive that command, it does not return a response to CONTROLLER. Consequently, no error code is also sent. The following lists the approximate waiting times for PROJECTOR to return the return Data after CONTROLLER sends the command. .
Appendix
Item Number Item name Upper byte 6 Lower byte Input 00h 01h Picture Mode 00h 02h Contrast Brightness Color Hue Sharpness Volume 00h 00h 00h 00h 00h 00h 10h 11h 12h 13h 14h 16h Color Temp 00h 17h DDE 00h 18h Wide Mode 00h 20h PictureMuting 00h 30h AudioMuting 00h 31h Input-A Signal Sel 00h 32h Lamp Mode 00h 40h Item name Video S-Video Input-A HDMI User3 Standard User1 User2 Cinema Dynamic Set Value Set Value Set Value Set Value Set Value Set Value Item name Item Number Upper byte Status Error 01h Status Power 01h Lamp Timer ROM Version 01h 01h Status Security *3 01h Sircs (15 Bit Category) Sircs (20 Bit Category) 17h 19h Item name No Error Lamp Error 01h Fan Error Cover Error Temp Error Stanby Start Up Lamp Power On Cooling1 02h Cooling2 Saving Cooling1 Saving Cooling2 Saving Stanby 13h Lamp Use Time MAIN ROM Version 1Dh Disable 1Fh Enable Refer to table 4 _ _ Refer to table 5 Lower byte Data Upper byte Lower byte 00h8 VPL-BW5 x3 SOFT SHARP CURSOR ↑ STATUS ON POWER*1 ON/OFF x5 CURSOR ↓ STATUS OFF x6 x7 MENU ENTER VIDEO COLOR + HIGH xA RESET INPUT A COLOR _ LOW xB *1 During the normal Standby (Low Power Standby) state, commands other than Power On/Off and Power On of the service direct commands are not accepted. When the Power On/Off or Power On command is received, the Full Power Standby state is established, and other commands can also be accepted.
VPL-BW5 9 7x 6x 5x 4x 3x 2x 1x 0x APA x0 DOT PHASE x1 (2) 20BIT Category x2 x3 x4 x5 x6 FREEZE x7 x8
x9 DIGITAL ZOOM + V KEYSTONE xA DIGITAL ZOOM – xB xC xD xE xFThe material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation. Le matériel contenu dans ce manuel consiste en informations qui sont la propriété de Sony Corporation.
VPL-BW5 (UC) VPL-BW7 (SY) VPL-BW7 (UC) VPL-BW7 (CN) E 9-883-664-02 Sony Corporation Printed in Japan 2009.
