3-218-492-12 (1) Video Projector Operating Instructions VPL-VW60 © 2007 Sony Corporation
WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Disposal of Used Lamp This projector’s lamp contains mercury and should be disposed of properly. Consult your local authorities regarding safe disposal. The material contained in this lamp are similar to those of a fluorescent lamp, so you should dispose of it in the same way. For customers in the United States Lamp in this product contains mercury. Disposal of these materials may be regulated due to environmental considerations.
For customers in Canada This Class B digital apparatus complies with Canadian ICES-003. Voor de klanten in Nederland Gooi de batterij niet weg maar lever deze in als klein chemisch afval (KCA). The socket-outlet should be installed near the equipment and be easily accessible. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSED OF USED BATTERIES ACCORDING TO THE LOCAL RULES.
Table of Contents Precautions ......................................... 7 Location of Controls Front/Right Side .................................8 Rear/Bottom .......................................9 Remote Control ................................10 Connections and Preparations Unpacking ........................................11 Step 1: Installing the Projector .........12 Before Setting Up the Projector .....................................12 Positioning the Projector and a screen ......................
Others About the HDMI Control ................. 53 Troubleshooting ............................... 54 Warning Indicators ..................... 56 Message Lists ............................. 57 Replacing the Lamp and the Air Filter and cleaning the Ventilation holes (intake) ............................................. 58 Cleaning the Air Filter ..................... 61 Specifications ................................... 62 Preset Signals .............................
Precautions On safety • Check that the operating voltage of your unit is identical with the voltage of your local power supply. • Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it further. • Unplug the unit from the wall outlet if it is not to be used for several days. • To disconnect the cord, pull it out by the plug. Never pull the cord itself. • The wall outlet should be near the unit and easily accessible.
Location of Controls Front/Right Side You can use the buttons on the control panel with the same names as those on the remote control to operate the projector. LENS button (1 page 22) M/m/
Location of Controls Rear/Bottom Ventilation holes (intake) (1 page 13) Remote control detector (1 page 21) Ventilation holes (intake) (1 page 13) Ventilation holes (intake) (1 page 13) Ventilation holes (intake) (1 page 13) Ventilation holes (intake) (1 page 13) Lamp cover (1 page 58) Adjusters (1 page 24) Filter holder (1 page 59) Ventilation holes (intake) (1 page 13) Projector suspension support attaching hole (1 page 69) 9
Remote Control Infrared transmitter ?/1 (ON/STANDBY) switch (1 page 22) LIGHT button Illuminates the buttons on the remote control.
Connections and Preparations Unpacking Check the carton to make sure it contains the following items: • Remote control (1) and Size AA (R6) batteries (2) • Lens cap (1) When you have purchased the projector, the lens cap is put onto the lens. Remove this lens cap when you use the projector. • Operating Instructions (this manual) • AC power cord (1) • ImageDirector3 CD-ROM (1) Inserting the batteries into the remote control Push and slide to open.
Step 1: Installing the Projector The projector displays pictures output from a VCR or other device. The lens shift allows you to have broader options for placing the projector and viewing pictures easily. Installing the projector in such a location may cause a malfunction of the unit due to moisture condensation or rise in temperature.
Improper use Do not do any of the following while using the projector. Ventilation holes (intake) Ventilation holes (exhaust) Tip For details on the location of the ventilation holes (intake or exhaust), see “Location of Controls” on pages 8 to 9. Tilting front/rear and left/right 15° or more Avoid using the projector tilted at an angle of more than 15 degrees. Do not install the projector anywhere other than on a level surface or on the ceiling.
Positioning the Projector and a screen The installation distance between the projector and a screen varies depending on the size of the screen. 1 Determine the installation position of the projector and screen. You can obtain a good quality picture if you position the projector with the center of the lens within the areas indicated in the gray areas in the illustration. Use the values a, b and c in the table on page 15 as a guide.
When using the 16:9 aspect ratio screen Unit: mm (inches) 40 60 80 100 120 150 180 200 250 300 (mm) 1016 1524 2032 2540 3048 3810 4572 5080 6350 7620 a 1212 (minimum) (47 3/4) 1842 (72 5/8) 2472 (97 3/8) 3102 3732 (122 1/4) (147) b 2105 (maximum) (82 7/8) 3181 4257 5333 (125 1/4) (167 5/8) (210) 6409 8023 9637 10713 13403 16093 (252 3/8) (315 7/8) (379 1/2) (421 7/8) (527 5/8) (633 5/8) c 485 (19 1/8) 971 (38 1/4) 324 (12 7/8) 647 (25 1/2) 809 (31 7/8) 4677 5622 6252 7827 9
2 Position the projector so that the lens is parallel to the screen. Top view Screen 3 Project an image on the screen and adjust the picture so that it fits the screen. (1 page 21) To project an image, connect video equipment to the projector. (1 page 17) Note When using a screen with an uneven surface, stripes pattern may rarely appear on the screen depending on the distance between the screen and the projector or the zooming magnifications. This is not a malfunction of the projector.
Step 2: Connecting the Projector Connecting to a VCR To connect to a DVD player/recorder, Blu-ray Disc player or digital tuner equipped with component video connectors Speakers AV amplifier Right side of the projector DVD player/recorder, HDD recorder, Blu-ray Disc player, digital tuner, etc.
To connect to a DVD player/recorder or Blu-ray Disc player equipped with HDMI output You can enjoy better picture quality by connecting a DVD player/recorder or Blu-ray Disc player equipped with HDMI output to the HDMI input of the projector. Moreover, if you have an HDMI control compatible equipment, you can operate the projector synchronizing with the HDMI control compatible equipment. For details, see the Function menu (1 page 48) and “About the HDMI Control” (1 page 53).
To connect to a VCR equipped with the S video connector or video connector Right side of the projector Speakers AV amplifier Video equipment to S video or video output S video or video cable (not supplied) : Video signal flow Tip If you do not know to which connector you should connect the cable, S VIDEO INPUT (S video input connector) or VIDEO INPUT (video input connector), connect it to S VIDEO to enjoy better picture quality.
Connecting to a Computer Right side of the projector Computer to monitor output HD-Dsub15 pin cable (not supplied) or HDMI cable (not supplied) : Video signal flow When using an optional HDMI cable, be sure to use a cable that has acquired the HDMI logo. Tip Set “Input-A Signal Sel.” in the Setup menu to “Auto” or “Computer.” If the input signal does not appear properly, set it to “Computer.
D:\job\3218492111\3218492111VPLVW60UC\010GB_VPLVW60UC\0 5PRE.fm masterpage:Left 00COV.book Page 21 Thursday, June 21, 2007 1:05 PM Step 3: Adjusting the Picture Position 1 Connections and Preparations Project an image on the screen and then adjust the picture position. ON/STANDBY indicator 4 Remote control detector 2 5,6,7 Tip The ?/1 (ON/STANDBY), INPUT, LENS, MENU, and M/m/
2 Press the ?/1 (ON/STANDBY) switch to turn on the projector. The ON/STANDBY indicator flashes in green, and then lights in green. When the ON/STANDBY indicator flashes, “Starting...” appears on the screen. 3 Turn on the equipment connected to the projector. Refer to the operating instructions of the connected equipment. 4 Press INPUT to project the picture on the screen. Each time you press the button, the input indication and equipment to be projected change.
The picture moves up by a maximum of 65% of the screen size from the center of the lens. Side view 120” 971 mm (38 1/4 inches) 65% 100” 809 mm (31 7/8 inches) 80” 647 mm (25 1/2 inches) 1 screen height center of lens (When using the 16:9 screen. For more details, see page 15.) : Picture position when the picture is moved upward at the maximum Tip You can also adjust the horizontal position of the lens.
Tip menu, you cannot adjust the picture size When “Lens Control” is set to “Off” on the Installation and the focus. (1 page 50) When “Test Pattern” is set to “Off” on the Function menu, the test pattern is not displayed. (1 page 49) 7 Adjust the focus. Press the LENS button repeatedly until the Lens Focus adjustment window (test pattern) appears. Then adjust the focus of the picture by pressing the M/m/
Step 4: Selecting the Menu Language 2,3,4 1 1 Press MENU. The menu appears. 25 Connections and Preparations You can select one of 16 languages for displaying the menu and other on-screen displays. The factory default setting is English. To change the current menu language, set the desired language with the menu screen.
2 Press M/m to select the Setup menu, and press , or . The setting items of the selected menu appears. 3 Press M/m to select “Language,” and press , or . 4 Press M/m/
Projecting Projecting the Picture on the Screen 1 Power on both the equipment and the device connected to the equipment. 2 Press INPUT repeatedly to select the input you want to project on the screen. Display the indication of the input you want. Example: To view the picture from the video equipment connected to the VIDEO INPUT connector.
Tips • When “Auto Input Search” is set to “On” in the Function menu, the input terminal with effective signals is automatically displayed by pressing INPUT. • When the “HDMI Control” is set to “On” in the Function menu, the input terminal with effective signals is automatically displayed, synchronizing with the operation of the equipment connected to HDMI 1 or HDMI 2 input of the projector. Turning Off the Power 1 Press the ?/1 (ON/STANDBY) switch. A message “POWER OFF?” appears on the screen.
Selecting the Wide Screen Mode You can enjoy various wide screen modes according to the video signal received. Press WIDE MODE. WIDE MODE button Original image When the Wide Mode is operated Wide Zoom A 4:3 aspect ratio picture is enlarged over the entire screen properly. The upper and lower portions of the screen are slightly cut off. Normal A picture with normal 4:3 aspect ratio is displayed in the center of the screen to fill the vertical screen size.
Letterbox picture with side panels Zoom A normal 16:9 aspect ratio picture is enlarged vertically and horizontally in the same ratio to fill the screen. Use this mode to view a letterbox picture or a letterbox picture with side panels. If the subtitle of a movie, etc. is hidden and cannot be seen, adjust the screen with “Vertical Size” and “V Center” to display the subtitle. (1 page 45) Letterbox picture Anamorphic Zoom When using an Anamorphic lens A 2.
Selecting the Picture Viewing Mode You can select the picture viewing mode that best suits the type of program or room conditions. DYNAMIC Enhances picture contrast and sharpness. STANDARD The quality of the picture becomes less rough than the one selected by “DYNAMIC”. CINEMA PICTURE MODE buttons DYNAMIC STANDARD CINEMA USER 1, USER 2 and USER 3 Recommended when viewing a movie in the dark place.
Adjusting the Picture Quality You can easily adjust the picture quality that suits your taste by selecting the adjustment items with the remote control. The adjusted data can be stored in each picture mode. Selecting to directly adjust the desired menu item Press COLOR SPACE, COLOR TEMP, BLACK LEVEL, GAMMA CORRECTION or ADVANCED IRIS.
Selecting desired adjust menu items in the order 1 2 1 For details on each adjustment, see the Picture menu. (1 page 40) Note Some adjustment windows cannot be displayed, depending on the type of input signal. For details, see “Input Signals and Adjustable/Setting Items” (1 page 67) 2 Example: To adjust the contrast Make the setting or adjustment on an item. When changing the adjustment level To increase the value, press ,. To decrease the value, press <.
Adjusting the Picture Using Real Color Processing The Real Color Processing (RCP) feature allows you to adjust the color and hue of each target of the projected picture you specify independently. You can thus obtain a picture more suitable to your taste. Tip Freeze the scene of the video source when you are adjusting the picture using Real Color Processing. 2, 3, 4, 5 1 Press RCP on the remote control. 2 Press M/m to select “User1,” “User2” or “User3,” then press ,.
2 Press M/m to select “Position” or “Range,” and specify it more delicate color position and color range you want to adjust using
Using the Menus This section describes how to make various adjustments and settings using the menus. Operation through the Menus The projector is equipped with an on-screen menu for making various adjustments and settings. Some of the adjustable/setting items are displayed in a pop-up menu, in a setting menu or adjustment menu with no main menu, or in the next menu window. If you select an item name followed by an arrow (B), the next menu window with setting items appears.
Press MENU. The menu window appears. 2 Press M/m to select a menu item, and press , or . The items that can be set or adjusted with the selected menu appear. The item presently selected is shown in yellow.
3 Pop-up menu Setting items Setting menu Adjustment menu Next menu window Setting items 38 Press M/m to select an item you want to set or adjust and press , or . The setting items are displayed in a pop-up menu, in a setting menu, in an adjustment menu or in the next menu window.
4 Make the setting or adjustment of an item. To reset the items that have been adjusted When changing the adjustment level Select an item in the Menu screen, and display the pop-up menu, the setting menu, and the adjustment menu. Press the RESET on the remote control to reset only the selected settings to its factory preset value. To increase the value, press M/,. To decrease the value, press m/<. Press to restore the original screen.
Picture Menu The Picture menu is used for adjusting the picture. Picture Mode You can select the picture viewing mode that best suits the type of picture or the environment. Dynamic: Select this for enhanced picture contrast and sharpness to reproduce color tones. Standard: Select this to reduce roughness compared to viewing the picture with Dynamic. Cinema: Select this for watching movies, etc. in a dark environment.
Cinema Black Pro Advanced Iris Switches the iris function during projection. Auto1: Automatically switches to an optimum iris according to a projected scene. The contrast of the scene is emphasized most. Auto2: An optimum iris becomes smaller than when set to “Auto1”. The contrast of the scene becomes reduced. Sensitivity: If “Auto1” or “Auto2” is selected, either “Recommend”, “Fast”, or “Slow” can be selected according to the desired response speed with Sensitivity Mode. Manual: Manually adjusts the Iris.
Expert Setting NR (Noise Reduction) Reduces the roughness or noise of the picture. Usually, select “Off”. If the picture is rough or noisy, select a setting from among “Low”, “Middle” or “High” according to the input signal source. DDE (Dynamic Detail Enhancer) According to the film source you have selected, make a setting for playback. Film: Normally, select this option. Reproduces the 2-3 Pull-Down film sources with smooth picture movement.
Advanced Picture Menu The Advanced Picture is used for adjusting the picture more. Using the Menus RCP (Real Color Processing) You can adjust the color and hue of each selected portion of the picture independently. User1, User2, User3: You can adjust the picture using Real Color Processing and store the settings. Once the settings are stored, you can view the picture with the adjusted picture quality. Off: Cancels this feature. For details, see “Adjusting the Picture Using Real Color Processing”.
Screen Menu The Screen menu is used to adjust the input signal. You can adjust the size of the picture, and select wide screen mode, etc. . Wide Mode (Video signal) You can set the aspect ratio of the picture to be displayed for the current input signal. This item is enabled only when a video signal (preset memory numbers 1 to 14) (1 page 64, 65) is input. Wide Zoom: A 4:3 aspect ratio picture is enlarged over the entire screen properly. The upper and lower portions of the screen are slightly cut off.
Screen Area Selects the size of the picture when a Hi-Vision picture is overscanned. Full: Expands the picture on the whole of the screen. Through: Does not expands the picture on the whole of the screen. Note This item is effective only when a Hi-Vision signal (preset memory No. 7, 8, 9, 12, 13 and 14) is input and “On” is selected in “Over Scan”. V Center Note This item is adjustable only when “Zoom” is selected. Vertical Size Reduces or enlarges the picture vertically.
Setup Menu The Setup menu is used to change the factory preset settings, etc. Status Sets whether or not the on-screen display is displayed. Set to “Off” to turn off the on-screen displays except for the menus, message when turning off the power, and warning messages. Language Selects the language used in the menu and on-screen displays.
Input-A Signal Sel. Selects the type of signal input from the equipment connected to the INPUT A connector. Selects the type of signal input from the equipment by selecting “Input-A” with the INPUT button. Auto: Selects the input signal type automatically. Computer: Inputs the signal from a computer. Video GBR: Inputs the signal from a TV game or HDTV broadcast. Component: Inputs the component signal from a DVD player/ recorder, Blu-ray Disc player, digital tuner, etc.
D:\job\3218492111\3218492111VPLVW60UC\010GB_VPLVW60UC\0 7MEN.fm masterpage:Left 00COV.book Page 48 Thursday, June 21, 2007 1:05 PM Function Menu The Function menu is used for changing the settings of the various functions of the projector. HDMI Control Selects the function whether to turn the HDMI Control function effective, when the HDMI 1 INPUT and HDMI 2 INPUT connectors are connected to an HDMI control compatible equipment.
Test Pattern Displays the test pattern. When set to “On,” a test pattern appears on the screen to be used when adjusting the lens with “Lens Focus,” “Lens Zoom,” and “Lens Shift,” or correcting the screen proportions with “V Keystone.” A test pattern does not appear when this item is set to “Off.” Tip While the test pattern is displayed, it is only displayed in green to allow you to adjust the focus easily. Background Using the Menus Selects the background color of the screen when no signal is input.
Installation Menu The Installation menu is used for changing the installation settings. V Keystone Corrects the vertical trapezoidal distortion of the picture. When the bottom of the trapezoid is longer than the top ( Sets a lower value (– direction) When the top of the trapezoid is longer than the bottom ( Sets a higher value (+ direction).
Blanking This feature allows you to adjust the displayable region within the four directions of the screen. Select each screen edge “left / right / top / bottom” on the Blanking adjustment screen with M / m buttons. Adjust the desired Blanking value with < / , button. Panel Alignment This feature allows you to adjust the gaps in the color of characters or the picture. When set to “On”, the “Adjust Color” and the “Pattern Color” can be assigned and adjusted.
Information Menu The Information menu displays the model name, serial number, the horizontal and vertical frequencies of the input signal and the cumulated hours of usage of the lamp. Model name: VPL-VW60 Serial No. Memory No. Signal type Model name Displays the model name (VPL-VW60). Serial No. Displays the serial number. fH (horizontal frequency) Displays the horizontal frequency of the input signal. fV (vertical frequency) Displays the vertical frequency of the input signal. Memory No.
Others This section describes about the other functions, how to solve the problems, how to replace the lamp and air filter, etc. About the HDMI Control HDMI Control is an HDMI standard mutual control function which uses the HDMI CEC (Consumer Electronics Control) specification. By connecting a variety of HDMI control compatible equipment such as a DVD recorder, an AV amplifier, etc.
D:\job\3218492111\3218492111VPLVW60UC\010GB_VPLVW60UC\0 8OTH.fm masterpage:Left 00COV.book Page 54 Thursday, June 21, 2007 1:05 PM Troubleshooting If the projector appears to be operating erratically, try to diagnose and correct the problem using the following instructions. If the problem persists, consult with qualified Sony personnel. Power Symptom The power is not turned on. Cause and Remedy c After about one minute, turn the power on.
Symptom Cause and Remedy The picture flickers. c Activate “APA”, then adjust the current input signal. c Adjust “Phase” for “Adjust Signal” in the Screen menu properly. (1 page 45) The color of characters or the picture is not appropriate. c Select the desired color registration in “Panel Alignment” of Installation menu (1 page 51). On-screen display Symptom Cause and Remedy c Set “Status” in the Setup menu to “On.” (1 page 46) c Check if the ?/1 (ON/STANDBY) indicator should light in green.
Warning Indicators The ON/STANDBY or LAMP/COVER indicator lights up or flashes if there is any trouble with your projector. ON/STANDBY indicator Symptom LAMP/COVER indicator Cause and Remedy LAMP/COVER flashes in red. (A repetition rate of 2 flashes) c Close the lamp cover securely, then tighten the screws securely. (1 page 58) c Close the filter holder securely. (1 page 60) LAMP/COVER flashes in red. (A repetition rate of 3 flashes) c The lamp has reached the end of its useful lifespan.
Message Lists Warning messages Message Cause and Remedy c Turn off the power. c Check to ensure that nothing is blocking the ventilation holes. (1 page 13) Frequency is out of range! c Frequency is out of range. Input a signal that is within the acceptable frequency range of the projector. Please check Input-A Signal Sel. c Set “Input-A Signal Sel.” in the Setup menu to “Computer” when an RGB signal is input from a computer. (1 page 47) Please replace the Lamp/ Filter.
Replacing the Lamp and the Air Filter and cleaning the Ventilation holes (intake) 1 Turn off the projector and unplug the AC power cord. 2 When setting the projector on a flat surface such as a desk etc., put a cloth to prevent the surface from being scratched. Reverse the projector as illustrated, then place it on the cloth. Tools you need to get started: Standard Phillips screwdriver Cloth (for scratch protection) The lamp used for the light source has a certain lifespan.
Loosen the three screws on the lamp with the Phillips screwdriver. Hold up the cover release lever, then pull the lamp straight out. 5 Ensure you push the new lamp all the way, then securely tighten those three screws on the lamp. Lock the cover release lever and put it back. 6 Close the lamp cover, then tighten the screws. 7 Remove the filter holder. 8 Remove the air filter. Others 4 Note Claws Be careful not to touch the optical block inside the unit.
9 Attach the new air filter so that it fits into the each claws (10 positions) on the filter holder. 14 Select “Yes”. Note Attach the Air Filter aligning it with the shape of the filter holder. Also, do not touch the fan after removing the air filter that is set deep inside the projector. 10 Attach the filter holder. Note The projector will not turn on unless the filter holder is securely closed. 11 Wipe dust off the Ventilation holes (intake) with a soft cloth.
Cleaning the Air Filter Others When “Please clean the filter.” appears on the screen, you should clean the air filter. The air filter should be cleaned every 1,500 hours. This value varies depending on the environment or how the projector is used. 1,500 hours are approximate. After washing the air filter with a mild detergent solution, dry it in a shaded place. Notes • When you clean the air filter, make sure you do not damage it.
Specifications HDMI INPUT A System Projection system SXRD panel, 1 lens, projection system LCD panel 0.61-inch (15.4 mm) SXRD panel 6,220,800 pixels (2,073,600 pixels × 3) Lens 1.8 times zoom lens (motorized) f18.7 to 33.7 mm/F2.54 to 3.53 Lamp 200 W Ultra High Pressure Lamp Projection picture size 40 to 300 inches (1,016 mm to 7,620 mm) (measured diagonally) Color system NTSC3.58/PAL/SECAM/NTSC4.
Supplied accessories Remote control RM-PJVW60 (1) Size AA (R6) batteries (2) AC power cord (1) Lens Cap (1) Operating Instructions (1) CD-ROM (ImageDirector3) (1) Design and specifications are subject to change without notice.
Warning on power connection Use a proper power cord for your local power supply.
Memory No. Preset signal (resolution) fH (kHz) fV (Hz) Sync H Size 1080/24PsF 1080/48i (1920 × 1080i) 27.000 48.000 SonG/Y – 10 720/60p 720/60p (1280 × 720p) 45.000 60.000 SonG/Y – 11 720/50p 720/50p (1280 × 720p) 37.500 50.000 SonG/Y – 12 1080/60p 1080/60p (1920 × 1080p) 67.500 60.000 – – 13 1080/50p 1080/50p (1920 × 1080p) 56.260 50.000 – – 14 1080/24p 1080/24p (1920 × 1080p) 26.973 23.976 – – 21 640 × 350 VGA-1 (VGA350) 31.469 70.
Memory No. Preset signal (resolution) fH (kHz) fV (Hz) Sync 50 1400 × 1050 SXGA + 65.317 59.978 H-neg, V-pos 1864 55 1280 × 768 1280 × 768/60 47.776 59.870 H-neg, V-pos 1664 56 1280 × 720 1280 × 720/60 44.772 59.
Input Signals and Adjustable/Setting Items Some of the items in the menus cannot be adjusted depending on the input signal. The following tables indicate them. The items that cannot be adjusted are not displayed in the menu. Item Input signal Component signal Video GBR signal PC signal Advanced Iris z z z z Lamp Control z z z z Contrast z z z z Brightness z z z z z z z – z (NTSC3.58/ NTSC4.43 only, except for B & W) z z – Color Temp.
Screen menu Item Input signal Video signal Component signal Video GBR signal Wide Mode z z z z *2 Over Scan – z z – Screen Area *1 – V Center *3 z z z z Vertical Size *3 z z z – APA – – – z *4 Phase – – – z *4 Pitch – – – z *4 Shift – z z z z (preset memory numbers 7, 8, 9, 12, 13, 14 only) z (preset memory numbers 7, 8, 9, 12, 13, 14 only) PC signal – z : Adjustable/can be set – : Not adjustable/cannot be set menu.
Ceiling Installation Use the PSS-H10 Projector Suspension Support when you install the projector on a ceiling. The projection distances for ceiling installation are shown below.
When using the 16:9 aspect ratio screen Unit: mm (inches) Screen Size 40 (inches) 60 80 100 120 150 180 200 250 300 (mm) 1016 1524 2032 2540 3048 3810 4572 5080 6350 7620 a Minimum Distance 1403 (55 1/4) 2033 (80 1/8) 2663 3293 3923 4868 5813 6443 8018 9593 (104 7/8) (129 3/4) (154 1/2) (191 3/4) (228 7/8) (253 3/4) (315 3/4) (377 3/4) Maximum 2296 Distance (90 1/2) x Minimum Distance 249 (9 7/8) Maximum 592 Distance (23 3/8) 3372 4448 5524 6600 8214 9828 (132 7/8) (175 1/8) (217
Attaching the PSS-H10 projector suspension support For details on installation on a ceiling, refer to the Installation manual for Dealers of the PSS-H10. Make sure to consult with a qualified Sony personnel for installation. The installation measurements are shown below when installing the projector on a ceiling using the PSS-H10. Top view Install the projector so that the center of the lens is parallel to the center of the screen. 191.
Front view 150 (6) 75 (3) Ceiling 175 (7) Center of the supporting pole The bottom surface of the mount bracket 93.5 (3 3/4) Center of the lens 197.5 (7 7/8) 197.5 (7 7/8) 395 (15 5/8) Side view 191.3 (7 5/8) 130 (5 1/8) Center of the lens Front of the cabinet 236.3 (9 3/8) 235.1 (9 3/8) 471.
Making Fine Adjustments to the Horizontal Picture Position Tools you need to get started Phillips screwdriver: 110 mm (4 3/8 inches) or longer Flat-head screwdriver: 110 mm (4 3/8 inches) or longer Note You can adjust the lens position right or left by about 1 mm from the center of the lens. 1 Remove the ring (washer) attached around the lens by turning it counterclockwise.
3 Insert a flat-blade screwdriver into the lens adjustment groove located at the left bottom (when the projector projects the image when placed on the floor, on a desk, etc.), and turn it in the direction in which you want to move the lens. If you turn it to the left, the lens moves to the left, and if you turn it to the right, the lens moves to the right. (The range of movement is approximately ± 1mm.
After you have decided the lens position, insert the Philips screwdriver at the locations of the four screws around the border of the lens in turn and tighten them to fix the lens in place. 5 Attach the ring (washer) by turning it clockwise. Others 4 Note When you use the horizontal and vertical lens shift features at the same time and adjust the horizontal lens shift to the maximum, the picture moves up to a maximum of 53% of its original position.
Index A Adjust Signal Phase ................................................... 45 Pitch ..................................................... 45 Shift ..................................................... 45 Adjuster ................................................... 24 Adjusting picture position .................................... 21 picture quality ...................................... 32 Advanced Iris .................................... 32, 41 Auto Input Search ...................................
R RCP .........................................................43 Remote control inserting the batteries ...........................11 location of controls ..............................10 Reset resettable items ....................................39 resetting the items ................................39 S Others Screen Area .............................................45 Selecting the menu language ...................25 Sharpness .................................................41 Specifications ........
Printed on 70% or more recycled paper. Standby power consumption 0.5 W Halogenated flame retardants are not used in cabinets and printed wiring boards.
