2-347-712-13(1) Wireless Microphone Package Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference.
For the AC adapter supplied with UWP-S1/S2 Important Safety Instructions • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. • Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
fermé. Ne confier l’entretien l’appareil qu’à un technicien qualifié. IMPORTANT La plaquette signalétique est posée sur le dessous de l’appareil (AC-S911). This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
WICHTIG Am Boden des Geräts befindet sich das Typenschild (AC-S911). WARNUNG Dieses Gerät hat keinen Netzschalter. Beim Einbau des Geräts ist daher im Festkabel ein leicht zugänglicher Unterbrecher einzufügen, oder das Netzkabel muss mit einer in der Nähe des Geräts befindlichen, leicht zugänglichen Wandsteckdose verbunden werden. Wenn während des Betriebs eine Funktionsstörung auftritt, ist der Unterbrecher zu betätigen bzw. das Netzkabel abzuziehen, damit die Stromversorgung zum Gerät unterbrochen wird.
ADVERTENCIA Esta unidad no tiene interruptor eléctrico. Cuando instale la unidad, incluya un dispositivo de desconexión de fácil acceso en el cableado fijo o enchufe el cable eléctrico a un tomacorriente cerca de la unidad y de fácil acceso. Si se produce una falla durante el funcionamiento de la unidad, utilice el dispositivo de desconexión para desconectar la electricidad o desenchufe el cable eléctrico.
For UTX-B1, UTX-H1, and UTX-P1 Transmitters Owner’s Record The model and serial numbers are located at the rear or on the bottom of the unit. Record the model and serial numbers in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. _____________________ Serial No. _____________________ IMPORTANT The name plate is located on the bottom and the serial number is located inside the battery compartment (UTX-P1).
Notice for customers in Canada: Use of Sony wireless devices is regulated by the Industry Canada as described in their Radio Standard Specification RSS-123. A licence is normally required. The local district office of Industry Canada should therefore be contacted. When the operation of the device is within the broadcast band, the licence is issued on no-interference, noprotection basis with respect to broadcast signals.
Notice for customers in Europe Notification aux clients européens Hinweis für die Kunden in Europa Avvertenza per gli utilizzatori in Europa Aviso para los clientes de Europa Nota para utilizadores da Europa Mededeling voor de klanten in Europa Att observera för kunder i Europa Meddelelse til kunderne i Europa Huomautus Euroopassa asuville asiakkaillemme U.K. Germany Norway Luxembourg Belgium Denmark France Italy Sweden Switzerland Finland Iceland 8 854.
Con questo Sony Corporation dichiara che questo UTX-B1/UTX-H1/UTXP1 è in conformità con i requisiti essenziali e altri provvedimenti in materia della Direttiva 1999/5/CE. Per dettagli, si prega di accedere alla seguente URL: http://www.compliance.sony.de/ Sony Corporation verklaart hierbij dat de UTX-B1/UTX-H1/UTX-P1 voldoet aan de primaire vereisten en andere relevante voorschriften van de Europese Bepaling 1999/5/EC. Nadere bijzonderheden vindt u op de volgende website: http://www.compliance.sony.
Sony Corporation julistaa täten, että tämä UTX-B1/UTX-H1/UTX-P1 vastaa direktiivin 1999/5/EC olennaisia vaatimuksia ja muita asiaankuuluvia määräyksiä. Katso tarkemmat tiedot osoitteesta: http://www.compliance.sony.de/ Huom! Joissakin maissa lisätaajuuskaistoja voidaan käyttää viranomaisten suostumuksella. Hinweis für Kunden in der Schweiz: Vor Inbetriebnahme ist eine Konzessionsanforderung für ein drahtloses Mikrofon (Frequenzklasse 3) bei Bakom einzureichen.
Note for customers in Italy: The use of this product within Italy is subject to article 334 of the Postal and Telecommunications regulations. Nota per i clienti in Italia: L’uso del prodotto sul territorio italiano è soggetto alle regolamentazioni del Codice Postale e delle Telecomunicazioni art. 334. Note for customers in Belgium: Using the UTX-B1/UTX-H1 with 30 mW RF output power is not allowed. Be sure to set the RF output power to 5 mW. The UTX-P1’s RF output power is 50 mW.
For URX-P1, URX-M1, and URX-R1 Tuners Owner’s Record The model and serial numbers are located at the rear or on the side of the unit. Record the model and serial numbers in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. _____________________ Serial No. _____________________ Notice for customers in the U.S.A.
les limites de la bande de radiodiffusion, la licence est accordée sur la base d’une non-interférence, non-protection pour les signaux de radiodiffusion. L’utilisation de cet appareil est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d’interférences, et (2) cet appareil doit accepter toutes les interférences, y compris les interférences capables de provoquer un fonctionnement non souhaité de l’appareil.
requirements and other relevant provisions of Directive 1999/5/EC. For details, please access the following URL: http://www.compliance.sony.de/ Sony Corporation déclare par ces présentes que le URX-P1/M1/R1 est conforme aux exigences essentielles et aux dispositions applicables de la Directive 1999/5/CE. Pour les détails, accédez à l’URL suivante: http://www.compliance.sony.
Para os clientes no Brasil O uso dos modulos UWP-C1, S1, X1 e UWP-C2, S2, X2 atende às normas e resoluções da Anatel, conforme homologação a seguir: 15
Table of Contents Table of Contents Configuration of the Packages ........................... 17 UWP-C1 ................................... 17 UWP-C2 ................................... 18 UWP-C3 ................................... 19 UWP-S1 ................................... 20 UWP-S2 ................................... 21 UWP-X1 .................................. 22 UWP-X2 .................................. 23 Features .................................. 24 Using the CD-ROM Manual ....
Configuration of the Packages This operation manual is for the UWP-C1/C2/C3/S1/S2/X1/X2 wireless microphone packages. The contents of each package are described below. UWP-C1 The UWP-C1 consists of a body-pack transmitter (UTX-B1) and a portable diversity tuner (URX-P1). When used in conjunction with a compact camcorder, the UWP-C1 makes a mobile system for ENG (Electronic News Gathering) or EFP (Electronic Field Production) purposes.
Configuration of the Packages UWP-C2 The UWP-C2 consists of a hand-held microphone (UTX-H1) and a portable diversity tuner (URX-P1). When used in conjunction with a compact camcorder, the UWP-C2 makes a mobile system for ENG (Electronic News Gathering) or EFP (Electronic Field Production) purposes.
UWP-C3 The UWP-C3 consists of a plug-on transmitter (UTX-P1) and a portable diversity tuner (URX-P1). When used in conjunction with a compact camcorder, the UWP-C3 makes a mobile system for ENG (Electronic News Gathering) or EFP (Electronic Field Production) purposes.
Configuration of the Packages UWP-S1 The UWP-S1 consists of a body-pack transmitter (UTX-B1) and a half-rack size diversity tuner (URX-R1). The UWP-S1 is suitable for constructing a wireless system for AV presentations.
UWP-S2 The UWP-S2 consists of a hand-held microphone (UTX-H1) and a half-rack size diversity tuner (URX-R1). The UWP-S2 is suitable for constructing a wireless system for AV presentations.
Configuration of the Packages UWP-X1 The UWP-X1 consists of a body-pack transmitter (UTX-B1) and a diversity tuner module (URX-M1). By installing the tuner module into a tuner base unit or a powered mixer, the system construction to meet the desired purpose of use and required system scale becomes possible.
UWP-X2 The UWP-X2 consists of a hand-held microphone (UTX-H1) and a diversity tuner module (URX-M1) . By installing the tuner module into a tuner base unit or a powered mixer, the system construction to meet the desired purpose of use and required system scale becomes possible.
Features Features Each of the UWP-C1/C2/C3/S1/S2/ X1/X2 wireless microphone packages (referred to as the UWP series hereafter) combines a transmitter (body-pack transmitter (UTX-B1), hand-held microphone (UTX-H1), or plug-on transmitter (UTX-P1)) and a receiver (portable diversity tuner (URX-P1), half-rack size diversity tuner (URX-R1), or diversity tuner module (URX-M1)).
Portable diversity tuner (URXP1) This tuner employs a space diversity system with little signal dropout and two angle-adjustable antennas. It comes with an adapter for mounting the tuner on the compact camcorder (DSR-PD170/PD170P, HVR-Z1, etc.). Half-rack size diversity tuner (URX-R1) This tuner employs a space diversity system with little signal dropout and two angle-adjustable antennas. It comes with two types of audio connectors (1/4-inch jack and XLR type) on the rear panel.
Using the CD-ROM Manual Using the CD-ROM Manual The supplied CD-ROM includes operating instructions for the UWP series wireless microphone packages (English, Japanese, French, German, Italian, and Spanish versions) and Sony Wireless Microphone System Frequency Lists (English, French, German, and Spanish versions). CD-ROM system requirements The following are required to access the supplied CD-ROM disc.
1 Insert the CD-ROM disc in your CD-ROM drive. A cover page appears automatically in your browser. 2 Select and click the frequency list that you want to read. A PDF file of the frequency list opens. Note If you lose the CD-ROM disc or become unable to read its content, you can purchase a new CD-ROM disc to replace one that has been lost or damaged. Contact your Sony service representative.
Precautions Precautions • The UWP series product must be used within a temperature range of 0°C to 40°C (32°F to 104°F). • Operating the UWP series product near electrical equipment (motors, transformers, or dimmers) may cause it to be affected by electromagnetic induction. Keep the UWP series product as far from such equipment as possible. • The presence of the lighting equipment may produce electrical interference over the entire frequency range.
Parts Identification Body-pack transmitter (UTX-B1) A AF (audio frequency) indication Appears whenever the input audio signal is stronger than the reference level. B RF (radio frequency) indication Appears during signal transmission from the antenna. C RF (radio frequency) level indication Shows the RF output level setting. For details, see “Setting the RF output level” on page 52. D BATT (battery) indication Shows the battery condition. For details, see “Power Supply” on page 38.
Parts Identification 5 + (+ selection) / – (– selection/ reset) buttons Press these buttons to set the transmission channel, frequency, or attenuation level of the input signal. The “–” button resets the accumulated battery use time to “00:00”. 1 Power indicator Lights up red when the microphone is turned on. 6 Battery compartment Accommodates two LR6 (size AA) alkaline batteries. For details on how to insert the batteries, see “Power Supply” on page 38.
D BATT (battery) indication Shows the battery condition. For details, see “Power Supply” on page 38. Plug-on transmitter (UTX-P1) Front side E CH (channel) indication Shows the transmission channel. Each time you press the SET button, the channel indication changes as follows. For details, see “Settings” on page 47. Transmission channel Transmission frequency Attenuation level of the input signal Press the SET button.
Parts Identification 2 AF/PEAK (audio frequency/ peak) level indicator The color indicates the strength of the audio input signal. On in red: Audio input level is –40 dBV or more (when the INPUT selector is set to MIC) or +8 dBV or more (when the INPUT selector is set to LINE). On in green: Audio input level is –60 dBV or more and less than –40 dBV (when the INPUT selector is set to MIC) or –9 dBV or more and less than +8 dBV (when the INPUT selector is set to LINE).
Portable diversity tuner (URX-P1) Transmission channel Transmission frequency Attenuation level of the input signal Press the SET button. Accumulated battery use time The channel/frequency indications for U66 model are shown. 5 + (+ selection) / – (– selection/ reset) buttons Press these buttons to set the transmission channel, frequency, or attenuation level of the input signal. The “–-” button resets the accumulated battery use time to “00:00”. 6 SET button Press to change display parameters.
Parts Identification 4 Display section C A B RF BATT AF CH Reception channel group and number Reception frequency Press the SET button. Accumulated battery use time D A RF (radio frequency) indications The number of dots indicates the RF input level. B AF (audio frequency) indication Appears whenever the output audio signal is stronger than the reference level. C BATT (battery) indication Shows the battery condition. For details, see “Power Supply” on page 38.
9 OUTPUT (audio output) connector (3.5-mm diameter stereo mini jack) Connect one end of the supplied XLRBMP conversion cable or the stereo mini plug-BMP conversion cable here and the other end to the microphone input on a camcorder, mixer, or amplifier. If the microphone input connector on the device connected to the tuner is a stereo mini jack, connect the straight (BMP) plug to the tuner and the L-shaped (stereo mini) plug to the microphone input connector on the device.
Parts Identification B AF (audio frequency) indication Appears whenever the output audio signal is stronger than the reference level. C GP (group)/CH (channel) indication Shows the reception channel group and channel number. Each time you press the SET button, the channel indication changes as follows. For details, see “Settings” on page 47. Reception channel group and number Reception frequency Press the SET button.
2 RF (radio frequency) indicator The color indicates the strength of the RF input signal. On in green: RF input is 25 dBµ* or more. Off: RF input is less than 25 dBµ*. Reception channel group and number Reception frequency Press the SET button. 3 Display section 4 + (+ selection) / – (– selection/ reset) buttons Press these buttons to set the reception channel and frequency. A B RF AF CH C A RF (radio frequency) indications The number of dots indicates the RF input level.
Power Supply Power Supply This section explains the power supply for each component. • Half-rack size diversity tuner (URX-R1) Connect the supplied AC adapter to the DC IN 9V connector on the rear panel, and then connect the AC adapter to a wall outlet. • Diversity tuner module (URX-M1) When incorporated into another component (e.g., MB-806A, SRPX700P, etc.), the tuner module draws its power from that component.
Hand-held microphone (UTX-H1) 1 Turn the grip in the direction of the arrow to open the battery compartment. 2 Align two new LR6 (size AA) alkaline batteries with the polarity markings and insert them into the battery compartment. 3 Plug-on transmitter (UTX-P1) 1 Slide the battery cover to release the lock and open the battery compartment. 2 Align two new LR6 (size AA) alkaline batteries with the polarity markings and insert them into the battery compartment, and then close the cover.
Power Supply Battery indication When you turn the power on, the battery condition is shown by the BATT indication in the display section. When the indication in column 4 starts to flash, replace the batteries with new ones. Be sure to check the expiration date printed on the new batteries before using them.
Attachment and Installation Procedures This section describes the procedures for attaching the supplied accessories to components and the installation of the diversity tuner module (URX-M1) into the MB-806A Tuner Base Unit or SRP-X700P Powered Mixer. Attaching the supplied accessories to the body-pack transmitter (UTX-B1) Attaching the wind screen to the microphone Insert the microphone into the hole at the bottom of the windscreen.
Attachment and Installation Procedures Removing the belt clip Insert a pointed object such as a ballpoint pen between the belt clip and the transmitter to make some space between them, and then remove the end of the belt clip from the hole on the side of the transmitter. Attaching the supplied accessory to the handheld microphone (UTX-H1) Attaching the microphone holder Insert the bottom part of the microphone into the holder.
Attaching optional accessory to the plugon transmitter (UTX-P1) Attaching a microphone or a cable Attaching the supplied accessories to the portable diversity tuner (URX-P1) Connecting a supplied conversion cable to the OUTPUT connector Example: XLR-BMP conversion cable (supplied) Push the microphone or cable connector (XLR-3-12C connector) against the audio input connector of the UTX-P1 until it clicks into place.
Attachment and Installation Procedures Attaching the shoe mount adapter Attaching the microphone stand adapter After attaching the belt clip and the shoe mount adapter, insert the microphone stand adapter into the screw hole at the top of the shoe mount adapter, and then rotate the microphone stand adapter until it is securely attached. Be sure to hold the horizontal part of the belt clip with the horizontal groove on the shoe mount adapter.
• The buttons and display on the front panel of the diversity tuner module (URX-M1) may be damaged if they are gripped too strongly. Always hold the diversity tuner module by the side. • Do not put your fingers on the connectors on the rear panel of the diversity tuner module (URX-M1) or into the slot on the unit into which the diversity tuner module (URXM1) will be installed. • Keep the diversity tuner module (URX-M1) away from static electricity.
Attachment and Installation Procedures Installing a diversity tuner module (URX-M1) into an SRP-X700P Powered Mixer SCENE RECALL MASTER A B ECT LINE 4 SEL A B C The SRP-X700P Powered Mixer can accommodate up to 2 diversity tuner modules (URX-M1). 1 Remove the tuner slot cover from the SRP-X700P and inspect the top and bottom sides of the diversity tuner module. Then, holding the tuner module on both sides, insert it into the slot.
Settings Setting the transmission channel The procedure below is the same for all UWP series transmitters (UTX-B1/H1/P1). Refer to the pdf files “Sony Wireless Microphone System Frequency List” on the supplied CD-ROM for details on the selectable channel groups and channels (for U62, U66, CE62, and CE67 models) or the supplied leaflet “Sony Wireless Microphone System Frequency List” (for AU66 and CE67 models). 1 Turn on the transmitter while pressing down the SET button.
Settings 4 When the desired channel number (or frequency) appears, set the POWER switch to OFF to complete the setting, or press the SET button to set other items. The results are stored in memory. The stored channel number (or frequency) will appear in the display section the next time you turn on the transmitter by setting the POWER switch to ON.
4 Pressing the – button cycles the indications in the opposite direction. Hold down the + or – button to change the channel group faster. 6 When the desired channel group number appears, press the SET button. To select the channel by frequency indication 1 The selected group is entered. The right four digits start to flash to allow the selection of the channel number.
Settings All the tuner modules installed into the MB-806 are set to the available channels within the selected channel group. After the automatic detection and selection of available channels finish, you can change the group and channel on each tuner module manually. • Make sure that the selected channel is the same on the transmitter and tuner being used in the same system.
Do the following while there is signal transmission. Press the SET button repeatedly until the attenuation level indication appears in the display section. 2 Press the + or – button to select the attenuation level. The accumulated battery use time is the total time (in hours and minutes) that the batteries have been used. It is recorded whenever the transmitter/ microphone/tuner is on. Reset the indication to “00:00” whenever you replace the batteries.
Settings The change becomes effective the next time you turn on the unit by setting the POWER switch to ON. 4 4-b For the portable diversity The results are stored in memory. The change becomes effective the next time you turn on the transmitter by setting the POWER switch to ON. tuner (URX-P1) Leave the tuner for about 10 seconds until the time indication stops flashing and the setting is stored in memory.
Operation The procedure below is the same for all UWP series components (UTX-B1/H1/P1 and URX-P1/R1/M1). 1 Make all necessary connections on the tuner. For examples of UWP series component connections, see “System Configurations” on page 54. 2 Set the transmission channel on the transmitter, and then turn off the unit. For details on setting the transmission channel, see “Setting the transmission channel” on page 47. 3 Turn on the tuner.
System Configurations System Configurations Note Production of the peripheral and relating devices may have been discontinued. Upon selecting the devices to be used with this product, consult your nearest Sony representative or the dealer from whom you purchased the product.
Sample configurations for AV presentations Portable diversity tuner (URX-P1) (with the belt clip, the shoe mount adapter, and the microphone stand adapter attached) Hand-held microphone (UTX-H1) Body-pack transmitter (UTX-B1) To DVD player, PC, or VTR, etc. SRP-X500P/X700P Powered Mixer or Hand-held microphone (UTX-H1) Half-rack size diversity tuner (URX-R1) To DVD player, PC, or VTR, etc.
System Configurations Sample configuration of a PA system Hand-held microphone (UTX-H1) AN-820 UHF antenna Diversity tuner module (URX-M1) Body-pack transmitter (UTX-B1) To DVD player, PC, or VTR, etc.
Configuration example of the UWP-C3 DMX-P01 Digital Portable Mixer F-112 Dynamic Microphone or Plug-on transmitter (UTX-P1) Portable diversity tuner (URX-P1) (with the belt clip and the shoe mount adapter attached) or DMX-P01 Digital Portable Mixer Portable diversity tuner (URX-P1) DVCAM Digital Camcorder (DSR-PD170/PD170P, HVR-Z1, etc.
Error Messages Error Messages When a problem occurs, one of the following error messages may appear on the display. Messages Meanings Remedy Err 01 An error has occurred in the backup memory data. Contact your Sony dealer. Err 02 The PLL synthesized circuit is abnormal. Restart the unit. If the message appears again, contact your Sony dealer. Err 03* The battery voltage exceeds the allowable limit. Use the specified batteries.
Troubleshooting If you have any problem using the UWP system, use the following checklist. Should any problem persist, consult your Sony dealer. Symptom Meanings/Remedy The unit does not turn on*. The polarity orientation of the batteries in the battery compartment is incorrect. b Insert the batteries with the correct polarity orientation. The batteries are exhausted. b Replace the batteries with new ones. The battery terminals in the transmitter are dirty.
Troubleshooting Symptom Meanings/Remedy There is distortion in the sound. The attenuation level of the transmitter is too low. b The input level of the tuner is extremely high. Press the – button on the transmitter in attenuation level setting mode to raise the attenuation level. The transmitter and the tuner are set to different channels. b Set the transmitter to the same channel. There is sound interruption or noise.
Specifications Transmitters (UTX-B1/ H1/P1) Items common to all transmitters Oscillator type Crystal-controlled PLL synthesizer Carrier frequencies Model available in USA: 758 to 806 MHz Model available in Europe: 798 to 862 MHz Model available in Australia: 792 to 806 MHz Operating frequency band Model available in USA and Europe: 24 MHz BW Model available in Australia: 14 MHz BW Pre-emphasis 50 µs Frequency characteristics 50 Hz to 18 kHz Signal-to-noise ratio 60 dB or more Tone signal 32 kHz Attenuation
Specifications Mass 63 × 100 × 27 mm (2 1/2 × 4 × 1 1/8 inches) (w/h/d) (excluding the antennas) Approx. 140 g (5 oz) including batteries Hand-held microphone (UTX-H1) Microphone unit Dynamic Directivity Unidirectional Antenna 1/4λ wave length wire (internal) RF output level 30 mW/5 mW selectable Reference deviation ±5 kHz Distortion 1.0% or less Indicator Power on Dimensions Mass Plug-on transmitter (UTX-P1) RF output level 50 mW Reference deviation ±10 kHz Maximum deviation ±40 kHz Distortion 1.
Tuners (URX-P1/R1/M1) Items common to all tuners Type of reception Space diversity Oscillator type Crystal-controlled PLL synthesizer Reception frequencies Model available in USA: 758 to 806 MHz Model available in Europe: 798 to 862 MHz Model available in Australia: 792 to 806 MHz Operating frequency band Model available in USA and Europe: 24 MHz BW Model available in Australia: 14 MHz BW Signal-to-noise ratio 60 dB or more De-emphasis 50 µs Reference deviation ±5 kHz Frequency characteristics 50 Hz to 18 k
Half-rack size diversity tuner (URX-R1) Antenna 1/4λ wave length wire (adjustable angle) Squelch level 25 dBµ Audio output level –28 dBm (LINE level)/–58 dBm (MIC level) selectable Audio output connectors 1/4-inch jack, unbalanced (LINE level only) XLR-3-32 type, balanced Headphones output level 5 mW (16Ω) Display Channel, frequency Power requirements 9.0 V DC Dimensions Mass 212 × 44 × 209 mm (8 3/8 × 1 3/4 × 8 1/4 inches) (w/h/d) (excluding the antennas) Approx. 1.
