Operating Instructions

15
B Peak indicator
Lights up when the signal is 3 dB below the level at which
di
stortion begins as a warning of excessive input level.
C T
ransmitter power warning indicator
Displays an icon when the remaining battery capacity of
t
he transmitter being received is almost discharged.
• The icon is not displayed if the receive signal level is
lo
w.
• This function is enabled only when the transmitter is a
UT
X-B40/M40/P40.
D Tr
ansmitter muting status indicator
Displays an icon when the muting function of the
t
ransmitter being received is on.
• The icon is not displayed if the receive signal level is
lo
w.
• This function is enabled only when the transmitter is a
UT
X-B40/M40/P40.
E Ba
ttery level indicator
Displays the battery level. “USB” is displayed when
po
wer is supplied from the USB connector. “MI” is
displayed when power is supplied from an SMAD-P5
(option).
For details, see “Battery level indicator” (page 19).
F RF
(radio frequency input) level meter
Displays the RF input level. The number of lights will
ch
ange depending on the input level.
6 lights: 60 dBµ or higher
5 lights: 50 dBµ to 60 dBµ
4 lights: 40 dBµ to 50 dBµ
3 lights: 30 dBµ to 40 dBµ
2 lights: 20 dBµ to 30 dBµ
1 light: 10 dBµ to 20 dBµ
No lights: 10 dBµ or lower
G M
enu display section
Displays various functions. Press the + or – button to
swi
tch functions.
For details, see “Configuration menu” (page 31).
i NF
C SYNC (NFC communication) button
Press to start a channel scan and for NFC communication
w
ith the transmitter.
For details, see “Operation” (page 23).
j SET
button
Adjusts displayed function settings and enters the
di
splayed value.
Holding down the SET button while turning on the power
t
urns the transmitter on without transmitting a signal
(transmission stopped mode).
k POW
ER button
Turns the power on/off.
l OUTP
UT (audio output) connector (3.5-mm
diameter, 3-pole locking mini jack, balanced
output)
Connect one end of the supplied XLR-BMP conversion
out
put cable for the URX-P40/URX-P41D or the stereo
mini plug-BMP conversion cable for the URX-P40 here
and the other end to the microphone input on a camcorder,
mixer, or amplifier. If the microphone input connector on
the connected device is a stereo mini jack, connect the
straight (BMP) plug to the tuner and the L-shaped (stereo
mini) plug to the microphone input connector on the
device.
• To prevent damaging the tuner, do not apply a voltage
t
o this connector from a microphone external power
supply (MIC+48V) or other source.
• Connection to a plug-in power microphone input
con
nector is supported using the stereo mini plug-BMP
conversion cable for the URX-P40.
• When the SMAD-P5 (option) is connected, connecting
t
he stereo mini plug-BMP conversion cable for the
URX-P40 to a camcorder microphone input may cause
noise to occur. In that case, use the supplied shoe mount
adaptor.
• When the stereo mini plug-BMP conversion cable for
t
he URX-P40 is connected, the output becomes
unbalanced.
m A
uxiliary connector
Refer to the SMAD-P5 (option) operating instructions for
det
ails about attaching to this unit.
n USB
connector (USB Type-C)
Connect to a commercially available USB portable power
suppl
y.
When the power is turned on, the unit operates with
power
supplied by the USB portable power supply.
Notes
Notes
Function Operation
Supply ON Press button for one second or
lo
nger
Supply OFF Press button until the indicator turns
of
f
Notes