5-042-114-13 (1) UHF Wireless Microphone Package UHF Synthesized Transmitter UHF Synthesized Wireless Microphone UHF Synthesized Diversity Tuner Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference.
EXT.IN menu ............................................. 38 Transmitter Settings ................................. 39 Menu structure and operation ..................... 39 Setting the transmit channel........................ 40 Configuration menu .................................... 41 System Configuration Example ............... 45 Error Messages ......................................... 46 Troubleshooting ........................................ 47 Important Notes on Use............................
Configuration of the Packages This manual is for the UWP-D21/D22/D26/D27 Wireless Microphone Packages. The contents of each package are described below. Note Some of the packages may not be available in certain countries or areas. In addition, the U90 model can only be used in the USA. The use of U90 transmitters requires a license and is subject to restrictions on frequency selection and channel spacing. For details, consult your Sony dealer.
UWP-D22 The package consists of a hand-held microphone (UTX-M40), a portable diversity tuner (URX-P40), and their accessories. When used in conjunction with a compact camcorder, a mobile system for ENG (Electronic News Gathering) or EFP (Electronic Field Production) applications can be constructed.
UWP-D26 The UWP-D26 consists of a plug-on transmitter (UTX-P40), a body-pack transmitter (UTX-B40), a portable diversity tuner (URX-P40), and their accessories. When used in conjunction with a compact camcorder, a mobile system for ENG (Electronic News Gathering) or EFP (Electronic Field Production) applications can be constructed.
UWP-D27 The package consists of two body-pack transmitters (UTX-B40), a portable diversity tuner (URX-P41D) that can receive two frequencies, and their accessories. When used in conjunction with a compact camcorder, a mobile system for ENG (Electronic News Gathering) or EFP (Electronic Field Production) applications can be constructed.
Models available separately The transmitter and tuner in each package are available for purchase separately. The components provided with each product are given below.
• High visibility OLED display for indoor/outdoor use • USB connector for power supply (URX-P40 only) • Digital audio interface support using SMAD-P5 multiinterface shoe-mount adaptor (option)* Features The UWP-D21/D22/D26/D27 (UWP-D series) Wireless Microphone Packages comprise a transmitter (body-pack transmitter (UTX-B40), hand-held microphone (UTX-M40), or plug-on transmitter (UTX-P40)) and a receiver (portable diversity tuner (URX-P40 or URX-P41D)).
• Channel configuration supported in combination with the UWP-D series equipped with an infrared communication function • Output level control for receiver • Equipped with output mode with wide range of output level settings • High visibility OLED display for indoor/outdoor use • USB for power supply • Digital audio interface support using SMAD-P5 multiinterface shoe-mount adaptor (option)* Name and Function of Parts Body-pack transmitter (UTX-B40) * For details on cameras that support this function, visi
For details, see “Configuration menu” (page 41). • If a lavalier microphone other than the one supplied is connected, the proper performance may not be obtained. I Gain mode indicator Displays the gain mode setting. e Display section For details, see “Setting the audio gain (GAIN MODE)” (page 41). f + or – button Selects functions or values shown on the display. g Infrared detector Receives the frequency and compander mode set on the tuner.
You can disable the power supply operation of the POWER/MUTE button and change the muting function on/off control method from the configuration menu. Hand-held microphone (UTX-M40) For details, see “Setting the operation of the audio muting function (POWER/MUTE) (UTX-M40 only)” (page 42). d Battery compartment Accepts two AA batteries (alkaline, nickel metal hydride, or lithium dry cell batteries). For details on how to insert batteries, see “Power Supply” (page 18).
For details about the muting function, see “Setting the operation of the audio muting function (POWER/MUTE) (UTX-M40 only)” (page 42). Plug-on transmitter (UTX-P40) Front F Battery level indicator Displays the battery level. For details, see “Battery level indicator” (page 19). G Menu display section Displays various functions. Press the + or – button to switch functions. For details, see “Configuration menu” (page 41). H Gain mode indicator Displays the gain mode setting.
e Display section I Gain mode indicator Displays the gain mode setting. For details, see “Setting the audio gain (GAIN MODE)” (page 41). f + or – button Selects functions or values shown on the display. g Infrared detector Receives the frequency and compander mode set on the tuner. A RF transmission indicator Displays the current transmission status. h N-Mark Receives the frequency and compander mode set on the tuner.
a Antenna Portable diversity tuner (URX-P40) b PHONES (monitor) connector (3.5-mm diameter, stereo mini jack) Connect to headphones to monitor the audio output. Front Note Do not connect headphones with a monaural mini jack. This may short-circuit the headphone outputs, resulting in distorted sound output. c POWER indicator Displays the battery level.
j SET button Adjusts displayed function settings and enters the displayed value. Holding down the SET button while turning on the power turns the transmitter on without transmitting a signal (transmission stopped mode). B Peak indicator Lights up when the signal is 3 dB below the level at which distortion begins as a warning of excessive input level. C Transmitter power warning indicator Displays an icon when the remaining battery capacity of the transmitter being received is almost discharged.
a Antenna Portable diversity tuner (URX-P41D) b POWER indicator Displays the battery level. Front Indicator display Status On (green) Sufficient battery level Flashing (green) Battery is getting low Off Supply OFF c RF (radio frequency input) indicators Lights up as shown below depending on the RF input level of tuner 1 and tuner 2. On (green): Input level is 25 dBµ or more. On (red): Input level is 15 dBµ to 25 dBµ. Off: Input level is 15 dBµ or lower.
l PHONES (monitor) connector (3.5-mm diameter, stereo mini jack) Connect to headphones to monitor the audio output. C Transmitter muting status indicator Displays an icon when the muting function of the transmitter being received is on. Notes Note • The icon is not displayed if the receive signal level is low. • This function is enabled only when the transmitter is a UTX-B40/M40/P40. Do not connect headphones with a monaural mini jack.
Body-pack transmitter (UTX-B40) / portable diversity tuner (URX-P40/P41D) Power Supply The following describes the procedure using illustrations for the body-pack transmitter (UTX-B40). Batteries can be inserted in the portable diversity tuner (URX-P40/ P41D) in the same manner. This section describes the power supply of each device.
Locked Unlocked Hand-held microphone (UTX-M40) 1 3 Insert two new AA batteries into the battery compartment with 3 and # polarities in the correct orientation. 4 Close the battery compartment cover and turn the knob clockwise to lock the cover. Press and hold the POWER/MUTE button or POWER button to turn the power off. Note The button used to turn off power varies depending on the POWER/MUTE setting.
portable power supply or otherwise altering their positions. • If a USB Type-C adaptor (from a different connector type) or a cable that does not comply with the USB Type-C standard is used, noise may occur or power may not be applied correctly. Always use cables that comply with the USB Type-C standard. The battery level may not be displayed correctly when different kinds of batteries, different brand of batteries, or old batteries are used.
Attaching the wind screen to the microphone Attaching Accessories This section describes how to attach the supplied accessories to each device. Align and insert the microphone into the hole in the wind screen. Attaching accessories to the body-pack transmitter (UTX-B40) Attaching a belt clip Connecting the microphone Microphone (supplied) Tighten the threaded sleeve for a secure connection.
Disconnecting a microphone or cable Attaching accessories to the hand-held microphone (UTX-M40) Microphone or cable connector Attaching the microphone holder Release button Press the release button firmly until the lock is fully released, and pull the microphone or cable out slowly. Insert the base of the microphone into the holder.
Operation Procedure for all transmitters (UTX-B40/M40/ P40) and portable diversity tuner (URX-P40) 1 Connect the tuner as required. For details about example connections, see “System Configuration Example” (page 45). 2 Press and hold the POWER button for at least one second on the tuner to turn the power on. Note Some noise may occur when power is turned on. Accordingly, turn down the audio input level of devices connected to the tuner when turning the power on.
groups on tuners 1 and 2, turn on only one of the tuners at a time and press the NFC SYNC button to start scanning. • If you select a group other than a group that supports multiple channel operation and use two or more UWP-D series at the same time, interference may occur. Set the channel group taking into account multiple channels, or set it to an unaffected channel. Information about the channel set on the tuner is sent to the transmitter, and then the transmit channel is set.
Information about the channel and compander mode set on the tuner are sent to the transmitter, and then the transmit channel is set. “COMPLETE” is shown on the display of the transmitter and tuner, and the transmitter vibrates when setup is finished. If the transmitter is turned off when NFC communication is initiated, the transmitter automatically turns on and starts transmitting.
• VERSION (software version) display Tuner Settings Basic menu operation The basic menu operation is the same in simple mode and advanced mode. Menu structure and operation Procedure for portable diversity tuner (URX-P40) There are two menu display modes that can be selected according to the application. Function name Simple mode This mode displays only the required settings for the tuner and audio output. You can enable simple mode by setting MENU MODE (menu display mode) to SIMPLE.
Menu tree Basic menu operation MENU Meter screen RX1 RX2 EXT.IN PHONES OUTPUT LEVEL OUTPUT MODE RUNNING TIME MONITOR MODE POWER SOURCE SYNC MODE SCAN TYPE BATTERY TYPE DISPLAY MODE BRIGHTNESS FCT RESET VERSION Menu name Function name Setting 1 Press the MENU button and select the menu to set or change. Each time you press the button, the display switches between the meter screen, RX1, RX2, EXT.IN, and meter screen in that order.
3 Press the + or – button to select the desired group name, then press the SET button. • The channel group is set, and the channel number display starts flashing. • • • 4 Press the + or – button to select the desired channel number, then press the SET button. Searching for available channels within a group (Clear Channel Scan) The displays stops flashing and the desired channel is set.
5 4 Select YES, and place the N-Marks of the transmitter and tuner in close proximity. Information about the channel set on the tuner is sent to the transmitter, and then the transmit channel is set. If you do not want to set the transmitter channel, select NO or perform no action for ten seconds or longer to not send the setting to the transmitter. The search for available channels finishes and the displayed channel is set.
2 To cancel searching Press and hold the SET button for one second or longer. Press the – button. The display returns to the ACT CH SCAN screen. Press and hold until the channel group and “+” display starts flashing. 4 Press the SET button when the desired channel number starts flashing. The search for active channels finishes and the displayed channel is set. Adjusting the monitor audio level 3 Procedure for portable diversity tuner (URX-P40) Press the + button.
3 For details about adjusting the monitor audio level, see “Adjusting the monitor audio level” (page 30). Press the + or – button to set the desired monitor audio level, then press the SET button. The setting is saved and retained even after the power is turned off. Configuring transmitter settings via NFC communication (SYNC RX->TX) Configuration menu Transfers the frequency and compander mode set on the tuner to a transmitter using NFC communication.
Setting the menu display mode (MENU MODE) The frequency and compander mode for use on the tuner are set. Sets the menu display mode. SIMPLE: Displays only the required settings. ADVANCED: Displays all settings. Notes • NFC communication lasts approximately 20 seconds. Perform step 4 within 20 seconds of performing step 3. After 20 seconds have elapsed, NFC communication automatically finishes and the GP/CH menu appears.
For details, see “Searching for active channels within a group (Active Channel Scan)” (page 29). Press the + or – button to toggle between the channels. To exit the CH MEMORY function 1 2 Setting the compander mode (COMPANDER) Press and hold the SET button until “CANCEL?” is displayed. Sets the operating mode of the compander. UWP-D: High speech quality mode supported in combination with UWP-D series devices. UWP: Mode supported in combination with Sony UWP-series transmitters.
Setting the display brightness (BRIGHTNESS) Note The monitor output level does not change when you change the output level in the OUTPUT LEVEL menu. The monitor output level is adjusted separately. Adjusts the brightness of the OLED display using ten levels. The configurable values are given below. (Dark) 1 2 3 4 5 6 7 8 9 10 (Bright) For details about adjusting the monitor audio level, see “Adjusting the monitor audio level” (page 30). Note This function is displayed in advanced mode only.
Monitor audio level mode is activated, and displayed. is Communication method Tuner for configuration on URX-P41D each transmitter NFC Infrared communication communication To release monitor audio level mode 1 2 Press and hold the SET button, MENU button, or NFC SYNC button for one second or longer until “ESCAPE?” is displayed. Press the + or – button to display “YES,” and press the SET button. Transmitter The lock state is released. Notes • This function is released when the power is turned off.
Changing the display settings (DISPLAY MODE) Note This menu is not available on the Japan model, Korea model, 90U model, and E model. On these models, the frequency band cannot be selected. Changes the display mode of the OLED display when 30 seconds have elapsed without any button activity. AUTO OFF: If no button operation is performed for 30 seconds, the display will turn off. Press a button to turn on the display again. DIMMER: If no button operation is performed for 30 seconds, the display will dim.
The frequency and compander mode for use on the tuner are set. • NFC communication lasts approximately 20 seconds. Perform step 6 within 20 seconds of performing step 5. If more than 20 seconds have elapsed, a confirmation display appears prompting whether to start NFC communication. Restart the NFC communication. • During NFC communication, the signal from the configured tuner’s wireless microphone cannot be received. Notes • NFC communication lasts approximately 20 seconds.
Setting the frequency to an active channel (ACT CH SCAN) Note No audio will be output if the combination of transmitter and compander mode setting is incorrect. Searches for channels already in use. This is useful when using more than one tuner in combination with a single transmitter. Transmitter Compander mode of unit UWP-D UWP WL800 For details, see “Searching for active channels within a group (Active Channel Scan)” (page 29).
OFF: Select when not using an external microphone. PLUG-IN PWR: Select when using an plug-in power type microphone. MONO BMP+5V: Select when using a Sony lavalier microphone. Transmitter Settings Menu structure and operation Adjusting the input level (INPUT LEVEL) You can set the input level in the range –12 dB to +12 dB. Adjust according to the microphone to be connected. The factory default setting is 0 dB.
• RF POWER (RF transmit output level) select • +48V SUPPLY (+48 V power supply) setting (UTX-P40 only) • POWER LOCK (POWER button lock) function • RUNNING TIME (accumulated running time) display • MENU MODE (menu display mode) setting • MUTE SETTING (audio muting setting) function (UTX-B40/P40 only) • POWER/MUTE (power supply / audio muting) setting (UTX-M40 only) • AUDIO PHASE (phase switching) setting (UTX-B40 only) • COMPANDER (compander mode) setting • OCUPNCY SENS (motion detection sensor mode) setting
For details about the groups and channels in each frequency band, refer to the “Frequency List”. Adjusting the audio input attenuation level (ATTENUATOR) 5 You can set the audio input attenuation level in 3 dB increments to reduce noise distortion. The factory default setting is 9 dB on the UTX-B40, and 0 dB on the UTX-M40/P40. Press the + or – button to select the desired channel number, then press the SET button. The displays stops flashing and the desired channel is set.
If an excessive audio level is input, it may cause noise distortion or damage the playback/recording equipment. • “---” is displayed for ATTENUATOR and GAIN MODE if INPUT LEVEL is set to LINE, and the settings cannot be modified. The factory default setting is 00:00. Up to 99:59 can be displayed. 1 Press and hold the SET button until the time display starts flashing. Setting the transmit output level (RF POWER) 2 Press the – button to display “00:00 CLR” and press the SET button.
the characteristics of new alkaline LR6 (size AA) batteries from a specific manufacturer. TYPE2: Recommended setting when using rechargeable nickel metal hydride batteries. TYPE3: Recommended setting when using lithium dry cell batteries. POWER/MUTE button is released. The power cannot be turned on/off using the POWER/MUTE button. PTT HOLD: Audio is output while the POWER/MUTE button is pressed, and audio is muted when the POWER/ MUTE button is released.
Displaying the software version (VERSION) Displays the software version of the transmitter. Note This function is displayed in advanced mode only.
System Configuration Example The following is a configuration example for use with UWP-D series devices. Sample configuration for ENG (Electronic News Gathering) or EFP (Electronic Field Production) with a camcorder For URX-P40 portable diversity tuner Portable diversity tuner (URX-P40) (with shoe mount adaptor attached or XLR-BMP cable connection) or Plug-on transmitter (UTX-P40) or Hand-held microphone (UTX-M40) Body-pack transmitter (UTX-B40) XDCAM EX/HDV camcorder (HXR-NX3, etc.
Error Messages When a problem occurs, one of the following error messages may appear on the display. Message Meaning Solution EEP ERROR An error has occurred in the backup memory data. Contact your point of purchase or Sony service representative. PLL ERROR An error occurred in the PLL synthesizer circuit. Restart the unit. If the message persists, contact your point of purchase or Sony service representative.
Troubleshooting If you have any problem, use the following checklist before asking for repairs. If the problem persists, contact your point of purchase or Sony service representative. Symptom Cause Solution The unit does not turn The 3 and # polarity orientation of the batteries is Insert the batteries with the correct polarity incorrect. orientation (page 18). on. The batteries are getting low. Replace the batteries with new ones. The battery terminals are dirty.
Symptom Cause Solution There is no sound. The channel setting on the transmitter is different from that on the tuner. Use the same channel setting on both the transmitter and tuner. The transmitter is not transmitting signals, or the transmission output is weak. Confirm that the transmitter is turned on. Alternatively, reduce the distance between the transmitter and tuner. The transmitter is set to line level input.2) Switch to microphone input (page 42).
Symptom Cause Solution There is sound interruption or noise. The channel setting on the transmitter is different from that on the tuner. Use the same channel setting on both the transmitter and tuner. Two or more transmitters are set to the same channel. Two or more transmitters cannot be used on the same channel. Refer to the frequency list, and reconfigure the channel on each transmitter.
Symptom Cause Solution The transmitter The N-Marks of both units are not facing each channel cannot be set other, or they are too far apart. Or there may be via NFC some metallic object between the N-Marks. communication. The grip is open.6) The SYNC MODE menu setting is IR.7) Place the N-Marks approximately 5 mm from each other. Make sure there are no metallic or other objects near them. Change the SYNC MODE setting to NFC (page 35).
Do not place this product close to medical devices Important Notes on Use This product (including accessories) has magnet(s) which may interfere with pacemakers, programmable shunt valves for hydrocephalus treatment, or other medical devices. Do not place this product close to persons who use such medical devices. Consult your doctor before using this product if you use any such medical device. The use of some frequency bands may be restricted by law, depending on the country or region.
Tone signal frequency In UWP-D compander mode: 32.382 kHz In UWP compander mode: 32 kHz In WL800 compander mode: 32.768 kHz Supply voltage DC 3.0 V (two LR6/AA size alkaline batteries) DC 5.0 V (supplied from USB connector) NFC function Built-in IR SYNC function Built-in USB port USB Type-C Operating temperature 0 °C to 50 °C (32 °F to 122 °F) Storage temperature –20 °C to +55 °C (–4 °F to +131 °F) Specifications The N-Mark is a trademark or registered trademark of NFC Forum, Inc.
Battery life (measured with two LR6/AA size alkaline batteries at 25 °C (77 °F), DISPLAY MODE set to AUTO OFF) Approx. 8 hours with output power of 30 mW (UC, U, CE, LA, CN, TW models) Approx. 10 hours with output power of 10 mW (E, KR models) Dimensions 73 (2 7/8) Dimensions Mass 258 (10 1/4) 63 (2 1/2) ø48 (1 15/16) 19 (3/4) 63 × 73 × 19 mm (2 1/2 × 2 7/8 × 3/4 in.) (width / height / depth) (excluding antenna) Approx. 83 g (2.
42LA model: 638.125 MHz to 697.875 MHz (UHF-TV channels 42 to 51) 29CN model: 638.025 MHz to 694.000 MHz (UHF-TV channels 29 to 35) KR model: 925.125 MHz to 937.375 MHz E model: 794.125 MHz to 805.875 MHz TW model: 510.125 MHz to 529.875 MHz Signal-to-noise ratio 60 dB (1 kHz sine wave, 5 kHz modulation) 96 dB (1 kHz sine wave, max deviation) Audio delay Approx. 0.35 ms (analog output) Approx. 0.
Battery life Approx. 6 hours (measured with two LR6/AA size alkaline batteries at 25 °C (77 °F), DISPLAY MODE set to AUTO OFF) Dimensions 70 (2 7/8) 70 (2 7/8) Dimensions 63 (2 1/2) Mass 63 (2 1/2) 31 (1 1/4) Mass 63 × 70 × 31 mm (2 1/2 × 2 7/8 × 1 1/4 in.) (width / height / depth) (excluding antenna) Approx. 131 g (4.6 oz) (excluding batteries) Portable diversity tuner (URX-P41D) Audio output level –60 dBV (3.
Sony Corporation
