2-345-260-11 (4) Digital Graphic Printer Instructions for Use UP-D897 © 2005 Sony Corporation
Owner's Record For the customers in Canada The model and serial numbers are located at the rear. Record these numbers in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. This unit has been certified according to Standard CSA C22.2 No.601.1. Model No. ____________________ Serial No. ____________________ WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. For the customers in the U.S.A.
Consult your dealer. (According to standard EN60601-1-2 and CISPR11, Class B, Group 1) Caution When you dispose of the unit or accessories, you must obey the law in the relative area or country and the regulation in the relative hospital. Warning on power connection Use a proper power cord for your local power supply. 1. Use the approved Power Cord (3-core mains lead) / Appliance Connector / Plug with earthing-contacts that conforms to the safety regulations of each country if applicable. 2.
Table of Contents Getting Started Overview ................................................................ 5 Location and Function of Parts and Controls .... 5 Front Panel ......................................................... 5 Rear Panel .......................................................... 6 Connections ............................................................ 6 Connecting to the USB Connector ..................... 6 Installing the Printer Driver ................................ 6 Paper .....
Getting Started Quiet, High Quality, Fast Printing • Employs a thin thermal head with a built-in high speed drive IC, capable of high resolution images of 12.8 dots/mm. • Print speeds of approximately 1 high quality image (960 × 1280 dots) every 2 seconds when printing at high speed. • Standard image memory capable of handling and printing images up to 4096 × 1280 dots (approx. 320 × 100mm). • Monochrome printing with up to 256 shades of gradation.
G H Getting Started I FEED button (8, 14) Hold down to feed paper. While a print job is in progress, press to cancel the print job. COPY button (14) Prints another copy of the previous printout. You can make only one copy each time you press this button regardless of the print quantity set using the menu. OPEN button (8, 14) Press to open the paper door. While a print job is in progress, press to cancel the print job. J Paper cutter Cuts the paper as each image is printed.
Paper Paper You Can Use Print paper characteristics are as follows. Print Characteristics Paper Type TYPE I (Normal) UPP-110S TYPE II (High Density) UPP-110HD TYPE V (High Glossy) UPP-110HG Notes on storing and handling paper Getting Started Use only Sony UPP-110S/110HD/110HG paper designed for use with this unit. High print quality cannot be guaranteed if any other paper is used with this unit, and such paper could damage the unit.
2 Press the OPEN button to open the paper door. Getting Started Make sure that the paper is set straight. 4 3 Close the paper door and press on it to shut it. Remove the label from the leading edge of the paper, pull out about 15~20 cm (about 6~8 in.) of the paper, and then set the paper roll in the paper tray. Note To avoid exposing the paper to dust, dirt, etc. always handle it carefully when removing from its package and loading it in the unit.
Operation You can set up the unit according to its intended purpose, connected equipments or your individual preferences. You can store up to three settings as a set of user settings. Adjustments and Settings Using the Menu Operation You can carry out adjustments and settings to meet your requirements. Those settings and adjustments are retained even if the unit is turned off.
Item Menu List This section describes the menus displayed as you turn the jog dial. The setting surrounded by indicates the factory setting. Function BEEP To select whether BE: OFF: The operation the operation and tone does not sound. error tones sound [BE: ON]: The operation and error tones sound. BACK: Cancels the setting change and returns to the item selection column.
Item RSIZE Function b) SAVE SIDE c) To select whether [RS:OFF]: Prints the image or not the image at the original size. is enlarged RS:ON: Prints the image at a larger size, according to the paper size set by the printer driver. BACK: Cancels the setting change and returns to the item selection column. To register up to three kinds of settings SA:3: Registers the menu settings as No.3. SA:2: Registers the menu settings as No.2. [SA:1]: Registers the menu settings as No.1.
The back light on the LCD lights in green. 4 Press the jog dial. LCD Operation 2 The unit enters the mode in which you can select the printing direction. “DI:NOR,” which is the factory setting, is displayed on the LCD. “DI:NOR” is the currently selected setting. In this menu operation, you will change the setting to “DI:REV.” Confirm that “READY” is displayed on the LCD, and press the jog dial. 5 Display “DI:REV” in the LCD by turning the jog dial up or down, and then press the jog dial.
To cancel the setting 2 1 Display “BACK” by turning the jog dial in step 5. Display “LOAD” by turning the jog dial, and then press the jog dial again. 3 Display the number corresponding to the desired settings, and then press the jog dial. Settings corresponding to the number selected in step 3 are loaded. 2 Press the jog dial. The display on the LCD returns to “DIR.” To continue menu operations Make settings by repeating steps 3 to 5.
In the following figure, the currently selected paper is the UPP-110S paper. Printing Before Starting a Print Job Always check the following points: • unit connected correctly? (page 6) • Printer driver installed? (page 6) • Paper loaded correctly? (page 7) • Menu settings and menu adjustments done correctly? (page 9) Indicates the UPP-110S Indicates the UPP-110HD Indicates the UPP-110HG Operation Starting a Print Job 1 Press the power ON/OFF switch to turn the unit on.
Adjusting the Contrast and Brightness You can adjust the contrast and brightness of the unit using the CONTR control and BRIGHT control on the front panel. Operation To adjust the contrast You can adjust the contrast of printouts using the CONTR control. To make the contrast stronger: Turn the CONTR control clockwise. To make the contrast weaker: Turn the CONTR control counterclockwise. Note The contrast adjusting function is equivalent to “Light” of the density control provided with the printer driver.
Others ventilation holes (intake) on the left hand side and the ventilation holes (exhaust) on the rear of the cabinet. Precautions On Safety Others • Check the operating voltage before operation. Operate the unit only with a power source specified in “Specifications”. • Stop operation immediately if any liquid or solid object falls into the cabinet. Unplug the unit and have it checked by qualified personnel. • Unplug the unit from the wall outlet if you will not be using it for a long time.
Maintenance 3 Insert the cleaning sheet, with the black surface facing down, into the groove of the paper tray. Insert the cleaning sheet into the groove of the paper tray. Cleaning the Cabinet Use a wrung out damp cloth, or a damp cloth soaked in water and a mild detergent, to clean the cabinet surface. To avoid damaging the cabinet of the unit, never use alcohol, thinner, or any other type of organic solvent, or any type of abrasive cleaner, to clean the cabinet.
3 Clean the platen roller gently with a damp clothe soaked in water and a mild detergent. Platen roller Others Notes • After the surface of the platen roller wiped has been dried completely, turn the platen roller to clean another portion. • Do not turn the platen roller with hands. Use the FEED button to turn it. To clean another part of the surface of the platen roller, go to the next step. 4 Press and hold down the FEED button so that the platen roller turns automatically.
Medical Specifications Protection against electric shock: Class I Protection against harmful ingress of water: Ordinary Degree of safety in the presence of flammable anesthetics or oxygen: Not suitable for use in the presence of flammable anesthetics or oxygen Mode of operation: Continuous The design and these specifications are subject to change without prior notification. Troubleshooting Before you call for service, please check the problems and solutions described below.
Error Messages Messages appear on the LCD under the following conditions. Take the remedial actions shown next to the messages to correct the problem. Description and remedy DOOR The paper door is open. tClose the paper door until it is locked securely. EMPTY • There is no paper loaded. • Paper has been used up. tLoad some paper. (page 7) COOL The protection circuit that prevents the thermal head from overheating has been activated. tWait for the message to disappear.
S Index Specifications 18 C T Connections 6 Troubleshooting 19 E Error messages 20 G Getting Started 5 L Location and function of parts and controls front panel 5 rear panel 6 Index M Maintenance cleaning the cabinet 17 cleaning the platen roller cleaning the thermal head Menu basic operations 11 list 10 loading the menu settings menu flow 9 printing the menu list 13 storing the menu settings 17 17 13 13 O Overview 5 P Paper feeding 14 loading 7 notes on storing and handling 7 paper you can u
Sony Corporation
