2-699-693-11 (1) Printer Driver (for Mac OS X) Installation Guide This guide describes installation and the use of the Printer Drivers for Mac OS X. Before Using this Software Before using the printer driver, be sure to read the “ReadMe” file located on the CD-ROM.
Windows 2000 Table of Contents Operation Environment Requirements ................3 About This Document ............................................3 Installing the Printer Driver .................................4 Before Installation ..............................................4 Installation Procedure .........................................4 Using More Than One Printer ..............................7 Installation Procedure .........................................7 Uninstalling the Printer Driver ....
Windows 2000 Operation Environment Requirements The system requirements for use of the printer driver are as follows. • Operating system: Mac OS X 10.3 or later • Computer: Macintosh computer running Mac OS X, with USB port as standard equipment • Memory: 128 MB or more • Hard disk: At least 2 MB of free space at time of installation About This Document The screen messages and other information shown in this document assume connection of the UP-CX1.
Windows 2000 3 Installing the Printer Driver Double-click the [UP-CX1Series.pkg] icon. The following installation screen appears. Before Installation Connecting multiple printers When several UP-CX1 series printers are connected to a single computer, install the printer driver for the first printer, according to the explanation in “Installation Procedure.” Then connect the subsequent UP-CX1 series printers to the computer and refer to the section “Using More Than One Printer.
Windows 2000 6 To accept the Software License Agreement, click [Agree]. The installation destination screen appears. 9 Enter the administrator [Name] and [Password], and click [OK]. The restart confirmation sheet appears. 10 Click [Continue Installation]. The installation begins. When the procedure is finished, the following restart message appears. 7 Select the boot disk as destination volume and click [Continue]. The installation type screen appears. 11 Click [Restart].
Windows 2000 To verify that the printer is ready for use, bring up the Printer List in the Printer Setup Utility. If the model name of your UP-CX1 series printer is shown in the list, the printer can be used. To start the Printer Setup Utility, open [Applications] [Utilities] - [Printer Setup Utility]. 2 Click the [Add] button. The Printer Browser screen appears. You can also bring up the Printer Browser screen by clicking the [+] button in [Print and Fax]. Note In Mac OS X 10.4.
Windows 2000 2 Click the [Add] button. The following screen appears. Using More Than One Printer Installation Procedure 3 In the popup menu, select [USB]. 4 Select the printer with your printer name in [Product] and “Sony” in [Type]. Select “SONY UPCX1 series printer” for [Printer Model]. Then click the [Add] button. If more than one UP-CX1 series printer is to be connected to the computer, perform the installation procedure for the second and subsequent printers as described below.
Windows 2000 5 Connect the printer to be added to the computer, and turn power to that printer on. 4 After a while, the connected printer will be automatically recognized and added to the Printer List. When the printer is added to the list, the installation is complete. If there is already a printer with the same name as the printer to be added, change the name of the existing printer.
Windows 2000 Uninstalling the Printer Driver Uninstallation Procedure 7 Open [Library] - [Printers] - [SONY] - [UP]. 8 Move the files [UPCX1PM.plugin] and [UPCX1PrintColorSetup.plugin] to the trash. 9 In the [Finder] menu, select [Empty Trash]. The printer driver is now uninstalled. To uninstall the printer driver, proceed as follows. 1 Shut down all running applications. 2 Turn power to all UP-CX1 series printers connected to the computer off and disconnect the USB cables.
Windows 2000 Making Page Settings Before printing from an application, you should make the required page attribute settings. Page attributes include the printer to use, the paper size, the paper orientation, and scale settings. 1 4 Select the desired paper [Orientation] setting. 5 Select the desired [Scale] setting when wishing to enlarge or reduce the image while printing. When the settings have been made, click the [OK] button. From the [File] menu in the application, select Page Setup.
Windows 2000 Making Print Settings Before printing from an application, you should make print settings on the print sheet. To bring up the print sheet, access the [File] menu of the application, select [Print], and select the printer from the [Printers] popup menu. Print settings include the number of copies to print, the use of digital camera correction, color balance settings, lightness, etc. Setting the Graphics Attributes Select the [Graphics] popup menu in the print sheet.
Windows 2000 Color balance From the [Color Adjust] popup menu, select [Color Balance]. Adjust the color balance by moving the sliders left or right, or by directly entering values in the edit boxes. Click the [Restore Defaults] button if you wish to return all color balance settings to their default condition. Lightness Checking the Print Settings Select the [Summary] popup menu in the print sheet. A list of print settings appears.
