User guide SmartBand 2 (for iOS) SWR12
Contents Basics.............................................................................................3 Introduction........................................................................................3 Hardware overview............................................................................3 Charging your SmartBand 2..............................................................4 Assembly...........................................................................................
Basics Introduction Your SmartBand 2 is a companion product that connects wirelessly via Bluetooth® with your iPhone. Worn on your dominant wrist, it can monitor your body movements and interact with your iPhone to generate data about your daily life and habits. For example, the SmartBand 2 counts your steps and records data about your physical state while you walk or run. Your SmartBand 2 is a device you can wear everyday and features a sensor that monitors your pulse and helps determine your heart rate.
Charging your SmartBand 2 Before using your SmartBand 2 for the first time, you need to charge it for approximately 30 minutes. Sony chargers are recommended. Your SmartBand 2 turns off automatically when the charger is connected. You cannot turn on the device while a charger is connected. To charge your SmartBand 2 1 2 3 Plug one end of the USB cable into the charger or into the USB port of a computer. Plug the other end of the cable into the Micro USB port of your SmartBand 2.
To assemble your SmartBand 2 • Insert the core into the wristband in such a way that the power key is inserted underneath the power key cover. Wearing your SmartBand 2 You should wear the SmartBand 2 on your dominant hand and position the device on your wrist two fingers above the wrist bone. Wear your SmartBand 2 on your wrist snugly but comfortably, neither too tight nor too loose. In order for the SmartBand 2 to monitor your pulse, it should stay in place on your wrist.
• To turn off the SmartBand 2 Press and hold down the power key until your SmartBand 2 vibrates. All notification lights are on simultaneously and then turn off one by one. 6 This is an Internet version of this publication. © Print only for private use.
Setting up your SmartBand 2 Preparing to use your SmartBand 2 For your SmartBand 2 to work properly, you must install the latest version of the SmartBand 2 application on your iPhone, and then pair and connect your SmartBand 2 device with your iPhone using Bluetooth®. To set up your SmartBand 2 using Bluetooth® 1 2 3 Make sure that your SmartBand 2 device is fully charged and turned on. On your iPhone, make sure that you have installed and updated the SmartBand 2 application to the latest version.
Using your SmartBand 2 Using the SmartBand 2 application You can view and change settings for your SmartBand 2 by using the SmartBand 2 application on your iPhone. You can also view your current pulse, stress and physical activities, such as steps, from the SmartBand 2 application. Getting notified You can set your SmartBand 2 to vibrate when you get an incoming call or a notification from your iPhone. All notifications on a connected iPhone can be forwarded to your SmartBand 2.
Stress and recovery levels Stress & Recovery is determined using Heart Rate Variability (HRV). The heart rate is never constant and the time difference between two consecutive heartbeats changes from beat to beat. This variation is called Heart Rate Variability (HRV). If the variation in-between heartbeats is high, this indicates a relaxed or recovering state. If the variation is low, this indicates stress.
Measuring pulse and stress manually You can have your SmartBand 2 perform a reading of your pulse at any time, either from the device itself or from your iPhone. To get the best heart rate data when exercising, initiate the heart rate sensor a few minutes before your physical activity so that the sensor is able to detect your pulse. To measure your pulse and stress manually from your SmartBand 2 1 2 To start measuring your pulse and stress level, double-press the power key.
To add a Smart wake up alarm 1 2 3 4 5 6 On your iPhone, open SmartBand 2, then tap SmartBand™. Tap Smart wake up, then tap . Tap Wake up time and select the relevant values for the hour and minute. To edit a period, tap Wake up interval and select the relevant value. Tap Repeat, then mark the days on which you want the alarm to recur and tap Edit Alarm. When you’re finished, tap Back. To edit an existing Smart wake up alarm 1 2 3 4 On your iPhone, open SmartBand 2, then tap SmartBand™.
Remote control You can use your SmartBand 2 to control playback from the Music application on the connected iPhone. The three notification lights on the SmartBand 2 are blue when you are using it as a remote control. To allow your SmartBand 2 to control the iPhone Music application 1 2 On your iPhone, open SmartBand 2, then tap SmartBand™. Drag the slider beside Music control to the on position.
All lights illuminating in blue one by one, then turning off simultaneously Connected to an iPhone All lights illuminating in white one by one, then turning off simultaneously Not connected to an iPhone All lights flashing in orange continuously Measuring pulse and stress and recovery level manually All lights flashing in blue continuously Remote controlling All lights flashing in red continuously Low battery level All lights flashing in white continuously Incoming calls Light A flashing in whit
Important information Using your SmartBand 2 in wet and dusty conditions Your SmartBand 2 is waterproof and protected against dust, so don’t worry if you get caught in the rain or want to wash off dirt after wearing it for a period of time. But remember that the SmartBand 2 is only protected in fresh and chlorinated water up to 3m for a maximum of 30 minutes. Rinse the SmartBand 2 with fresh water under a faucet and dry the device completely after swimming.
Declaration of Conformity We, Sony Mobile Communications AB of Nya Vattentornet SE-221 88 Lund, Sweden declare under our sole responsibility that our product Sony type RD-0180 and in combination with our accessories, to which this declaration relates is in conformity with the appropriate standards EN 300 328:V1.8.1, EN 300 330-2:V1.5.1, EN 301 489-7:V1.3.1 EN 301 489-17:V2.2.1, EN 301 489-3:V1.6.
