WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. [N allele] RISK OF ELECTRIC SHOCK NANOBOT GEN AUCTION: TO HEDGE THE RISK OF ELECTRIC] SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE _REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user 10 the presence of insulates! “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
On operation « Before connecting other components, be sure to turn off and unplug the receiver. On cleaning * Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution, Do not use any type of abrasive pad, sousing powder or solvent such as alcohol or benzine. For the customers in the USA For detailed safety precautions, see the “IMPORTANT SAFEGUARDS” leaflet. If you have any question or problem conceding your receiver, please consult your nearest Sony dealer.
Getting Started 00 Unpacking Check that you received the following items with the receiver: + FM wire antenna (1) * AM loop antenna (1) * Remote controller (remote} (1) * Size AA (R6) batteries (2) Inserting batteries into the remote Insert two size: AA (R6) batteries with the + and on the battery compartment. When using the remote, point it at the remote sensor M on the receiver. " When to replace batteries Under normal use, the batteries should last for about 6 months.
Getting Started Antenna Hookups Overview This section describes how to connect AM and FM antennas to the receiver. If you want to receive radio broadcasts with the receiver, complete these connections first, then go to the following pages. For specific locations of the terminals, see the Frustration below.
Getting Started Hookups The arrow == indicates signal flow. b player Receiver CD player T W o= @@35 Turntable Receiver Tum table your turntable has an earth lead To prevent hum, connect the earth lead to the 4 ground terminal on the Receiver. Tape deck or MD recorder Receiver Tape deck or MD recorder tel TAD Receiver Cavort T o] bliss Receiver VCR [ (o] v 23l oo . 1o¢ Where do I go next? Go on to the next section to connect the speakers.
Selecting the speaker system To drive the speakers, select the speaker system as follows: To drive Depress SPEAKERS button Speaker system A (connected A to the FRONT SPEAKERS A terminals) Speaker system B (connected B to the FRONT SPEAKERS B terminals) Both speaker systems A and B A+B {series connection) Where do I go next? Go on to the next section to connect ant AC plug and complete your home theater system.
Receiver Operations Selecting a Component To listen to a connected component, first select the function on the receiver or with the remote. Before you begin, make sure you have: * Connected all components securely and correctly as indicated on pages 5to 7. Turned VOLUME to the leftmost position (0) to avoid damaging your speakers. POWER VOLUME Function buttons 1 Press POWER to turn on the receiver.
caver Operations Changing the factory setting of a function m button ‘ If the factory settings of the FUNCTION buttons (page 8) don't match your system components, you can change them. For example, if you have two CD players and you don’t have a tape deck or an MD recorder, you can assign the TAPE/MD button to your second CD player. Note that the settings of the TUNER and PHONON buttons cannot be changed.
Receiver Operations stereo program is distorted “The STEREO indicator fishes. Press FM MODE to change to monaural (MONO). You will not have the stereo effect ‘but the distortion will be reduced. To return to stairs mode, press this button again. é you cannot tune in a station and the entered numbers are flashing Make sure you've entered the right frequency. 1f not, ‘press DIRECT and re-enter the frequency you want.
Receiver Operations Tuning preset stations (preset tuning) er“ You can tune directly to a preset station by entering its '“g preset number. If you don't know which stations are ¢ on which numbers, you can tune by scanning This receiver makes it easy to record audio to and from the components connected to the receiver. You don't the preset stations. have to connect playback and recording components 4 Press TUNER. directly: once you select a program source on the The last received station is tuned in.
Additional information 12 Troubleshooting If you experience any of the following difficulties while using the receiver, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest Sony dealer. There's no sound or only a very low-level sound is heard. wp Check that the speakers and components are connected securely. =» Make sure you select the correct component on the receiver. =» Make sure you set the SPEAKERS selector correctly.
Specifications Audi power specifications POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 8-ohm load, both channels driven, from 40 20,000 Hz, rated 100 watts per channel minimum RMS power, with no more than 0.8 % total harmonic distortion from 250 milliliters to rated output. (USA model only) Amplifier section Dynamic power output Stems: 150 W+ 150 W ohms: ZION + 210 W Harmonic distortion at rated output Less than 0.
Additional information AR Recording H1LJKLMNO sonata Index Hookahs ner AC power cord 7 Remote b antennas 5 A B audio/video components 5,6 § Adjust overview 4 speakers 6,7 volume 7 st Antenna hookups 5§ P Selecting a Audio/ video component Presetting using tb hookups 5,6 radio stations 10 Speakers Automatic tuning 10 Preset tuning 10 connection Program source impedes C selecting 8,9 selecting Connecting. See Hookups Q Storing rai g i D Quick reference guide 16 Direct tuning 9,10 T Dubbing.
Re mate Button Descriptions Remote Button Descriptions For buttons not described on previous pages and buttons with names different from the buttons on the main unit. Remote Operates Function Remote Operates Function Button Button o8 Receiver Selects preset slumbers. RMS Tape deck Selects tape direction (for DIRECTION tape decks with the RMS* CD player/MD Selects track numbers, function.} recorder LD { selects track 10.
Quick Reference Guide A Receiver Broadcasts (direct tuning) Example: Receiving FM 102.50 MHz BANDY 773 Select FML 200 CEY [ Display naan [ T Scanning Radio Stations (automatic tuning) Example: Scanning FM stations TUNER ¥ BAND 01 Select FML * -~ TUNING + e To continue scanning. TUNING 4 el Sony Corporation Printed in Malaysia R Presetting Radio Selecting a Stations Component Example: Presetting a station asap Example: Playing a CD * Turn on the CD player. Tune in the station you want. + 3 Start playing.
