Remote Camera System Guide
Table Of Contents
- Table of Contents
- Read This First
- Chapter 1 Application
- Chapter 2 Connection & Basic Settings
- [A] Auto IP address setting from RM-IP500
- [B] IP address setting from RM-IP Setup Tool
- [C] Serial connection setting (RS-422/RS-232C)
- [D] Connection with 4K video switcher
- [E] Fiber connection from BRC-H900
- [F] Tally control from MCX-500
- [G] Connection with AWS-750
- [H] Connection with RCP-3500/3100/1500 series
- [I] Connection with MSU-1000/3000 series
- [J] NDI® | HX connection
- Chapter 3 Products
- Chapter 4 Edge Analytics Appliance Application
- Edge Analytics Appliance Application Configuration
- Usage example of Handwriting Extraction in the classroom
- Usage example of PTZ Auto Tracking in the lecture hall
- Usage example of Close-up by Gesture in the classroom
- Usage example of Chroma key-less CG Overlay in a small-scale studio
- Usage example of Focus Area Cropping at an event space
- Recommended cameras for connection with Edge Analytics Appliance
- Chapter 5 Appendix
000
Chapter 5: Appendix: Controller compatibility chart
60
Control block Button/knob Function Conditions BRC-X1000/H800/X400 BRC-H900 SRG series
*1 *2
FUNCTION menu of menu
control block
ASSIGN 4 to ASSIGN 5 buttons DETAIL LEVEL display – Yes Yes Yes
*5
Adjustment using VALUE knob after
DETAIL LEVEL is displayed
On the BRC-H900, enabled if DETAIL is set to ON in
the camera menu.
KNEE POINT display – Yes Yes –
Adjustment using VALUE knob after KNEE
POINT is displayed
Enabled when KNEE is set to ON in the camera
menu, and KNEE MODE is set to MANUAL.
AE level display Enabled when the AE button is lit, or if the AE button
is not lit and CONFIG >RM SETUP >AE CONFIG is not
set to MANUAL in the RM menu.
Yes Yes Yes
Adjustment using VALUE knob after AE
level is displayed
Enabled when OPERATION >EXPOSURE >EX-COMP
is set to ON in the RM menu.
ND filter ND1 to 4 settings – Yes
*8
– –
Picture profile PP1 to 6 settings – Yes – –
IRIS button (lit blue when
enabled)
IRIS setting display Enabled when the AE button is not lit. Yes Yes Yes
Adjustment using VALUE knob after IRIS
setting is displayed
Enabled when the AE button is not lit, and CONFIG
>RM SETUP >AE CONFIG is set to MANUAL or IRIS Pri
in the camera menu.
GAIN button (lit blue when
enabled)
GAIN setting display Enabled when the AE button is not lit. Yes
*9
Yes
*6
Yes
*6
Adjustment using VALUE knob after GAIN
setting is displayed
Enabled when the AE button is not lit, and CONFIG
>RM SETUP >AE CONFIG is set to MANUAL or GAIN
Pri in the camera menu.
SHUTTER button (lit blue when
enabled)
Shutter speed display Enabled when the AE button is not lit. Yes
*7
Yes
*7
Yes
*7
Adjustment using VALUE knob after
shutter speed is displayed
Enabled when the AE button is not lit, and CONFIG
>RM SETUP >AE CONFIG is set to MANUAL or
SHUTTER Pri in the camera menu.
*1 Applicable cameras: SRG-360SHE, SRG-300SE, SRG-300H, SRG-120DH/120DS/120DU, SRG-A40, SRG-A12, SRG-X400,
SRG-X120, SRG-X40UH, SRG-XB25, SRG-XP1
*2 If the camera menu EXPOSURE > MODE > FULL AUTO has a WIDE D (VIEW-DR) function, FULL AUTO mode cannot be
turned OFF with the AE button in settings other than OFF. If you want to switch between AUTO/manual with the AE
button, set WIDE D to OFF.
*3 Enabled when Exposure Mode is set to FULL AUTO or BACK LIGHT in the camera menu.
*4 Setting is enabled in the camera menu.
*5 Excluding SRG-A40, SRG-A12, SRG-X400, and SRG-X120, the APERTURE setting in camera PICTURE menu is applied.
*6 GAIN Pri cannot be selected.
*7 Setting changes with the frame rate (50 Hz/59.94 Hz). Set CONFIG > RM SETUP > CAMERA FREQ in the RM menu to the
frame rate setting of the camera.
*8 Applicable cameras: BRC-X1000, BRC-H800
*9 GAIN Pri is not available on BRC-X400
*10 Applicable cameras: SRG-A40, SRG-A12, SRG-X400
*11 Applicable cameras: SRG-A40, SRG-A12
If using the ILME-FR7, see “When using a panel sheet” (page 61).
Yes: Supported
–: Not supported