MZ-NF810/NF810CK SERVICE MANUAL US Model Canadian Model Ver 1.0 2003. 03 MZ-NF810CK AEP Model UK Model E Model Australian Model Chinese Model Tourist Model MZ-NF810 Photo : MZ-NF810 US and foreign patents licensed from Dolby Laboratories. • SonicStage, OpenMG and the OpenMG logo, MagicGate, Memory Stick and the MagicGate Memory Stick logo, Memory Stick and the Memory Stick logo, Net MD and the Net MD logo are trademarks of Sony Corporation.
MZ-NF810/NF810CK Modulation system EFM (Eight to Fourteen Modulation) Frequency response 20 to 20,000 Hz ± 3 dB Inputs1) MIC: stereo mini-jack (minimum input level 0.12 mV) Line in: stereo mini-jack for analog input (minimum input level 49 mV) optical (digital) mini-jack for optical (digital) input Outputs Dimensions Approx. 81.0 × 74.4 × 20.0 mm (w/h/d) (31/4 × 3 × 13/16 in.) Mass 1)The LINE IN (OPTICAL) jack is used to connect either a digital (optical) cable or a line (analog) cable.
MZ-NF810/NF810CK CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. TABLE OF CONTENTS 1. SERVICING NOTES ................................................ 4 2. GENERAL ................................................................... 5 On power sources 3. DISASSEMBLY • Use house current, nickel metal hydride rechargeable battery, LR6 (size AA) battery, or car battery.
MZ-NF810/NF810CK SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts.
MZ-NF810/NF810CK SECTION 2 GENERAL Looking at controls This section is extracted from instruction manual.
MZ-NF810/NF810CK SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. Disassembly Flow SET CASE (LOWER) MAIN BOARD, BATTERY CASE PANEL (UPPER) SECTION MECHANISM DECK (MT-MZN710-177) LCD MODULE, PANEL UPPER BLOCK OP SERVICE ASSY (LCX-5R) HOLDER ASSY 6 In order to remove mechanism deck (MT-MZN710-177) , please remove MAIN board and upper panel section.
MZ-NF810/NF810CK Note: Follow the disassembly procedure in the numerical order given. 3-2. Case (Lower) 6 two screws (M1.4) 7 Remove the case (lower) in the direction of the arrow. 4 two screws (M1.4) 5 screw (M1.4) 2 claw battery lid 1 Open the battery case lid. 3 Remove the battery case lid. 3-3. MAIN Board, Battery Case 2 Remove the solder of terminal (minus). 1 Remove the solder of terminal (plus). 3 Remove two solders of the flexible board (over write head). 6 five screws (M1.
MZ-NF810/NF810CK 3-4. Panel (Upper) Section 1 flexible board (CN871) 5 upper panel section 3 two screws (M1.4) set chassis assy 4 two screws (M1.4) torsion spring (pop up-L) 6 torsion spring (pop up-L) 2 Slide the open slider in the direction of the arrow, and open the upper panel section. 3-5. LCD Module, Panel Upper Block Note: On installation, adjust the position of both switch and knob (hold), knob (t mark). 1 six screws (1.7 × 2.
MZ-NF810/NF810CK 3-6.
MZ-NF810/NF810CK 3-7. OP Service Assy (LCX-5R) 2 gear (SA) 5 screw (M1.4) 1 washer (0.8-2.5) 6 thrust detent spring 3 screw (M1.4) 8 Pull off lead screw. 4 rack spring 7 9 Opening the over write head toward the direction A, remove the OP service assy (LCX-5R) toward the direction B. B Note: Do not open the entire assy forcibly, when opening the over write head.
MZ-NF810/NF810CK 3-8. Holder Assy 4 holder assy 2 Open the holder assy. 3 boss 1 convex portion 3 boss 3-9. DC Motor (Sled) (M602) 2 washer (0.8-2.5) 3 gear (SA) 4 two screws (M1.4) 5 DC motor (sled) (M602) 1 Remove six solders of the motor flexible board.
MZ-NF810/NF810CK 3-10. DC Motor (Over Write Head Up/Down) (M603), DC SSM18B Motor (Spindle) (M601) 1 Remove six solders of the motor flexible board. 2 tapping screw 3 motor cover 7 DC motor (over write head up/down) (M603) Note: Press-fit the gear (HA) up to the position of the DC motor (over write head up/down) (M603) as shown below. 8 three tapping screws 6 gear (HA) gear (HA) 3.
MZ-NF810/NF810CK SECTION 4 TEST MODE Outline Operation in Setting the Test Mode • This set provides the Overall adjustment mode that allows CD and MO discs to be automatically adjusted when in the test mode. In this overall adjustment mode, the disc is discriminated between CD and MO, and each adjustment is automatically executed in order. If a fault is found, the system displays its location. Also, the manual mode allows each individual adjustment to be automatically adjusted.
MZ-NF810/NF810CK Configuration of Test Mode [Test Mode $Display Check Mode%] Press the > or [VOL +] key [Manual Mode] Press the xCANCEL/CHG key [Servo Adjustment] [Audio Adjustment] [Power Supply Adjustment] [OP Alignment Adjustment] [VOL +] key: 100th place of item [Major item switching] number increase. [VOL --] key: 100th place of item > key xCANCEL/CHG key number decrease. [VOL +] key: 10th place of item number increase.
MZ-NF810/NF810CK 5. The display changes a shown below each time the [END SEARCH] is pressed or the [DISPLAY] key on the remote commander is pressed.
MZ-NF810/NF810CK • Description of error indication codes Problem Indication code No error Servo system error TOC error Power supply system error Offset system error Meaning of code No error 01 Illegal access target Adrs address was specified Attempt to access an abnormal address No error 02 High temperature Temp High temperature detected 03 Focus error Fcus Disordered focus or can not read an address 04 Spindle error Spdl Abnormal rotation of disc 11 TOC error TOC Faulty TOC cont
MZ-NF810/NF810CK Sound Skip Check Result Display Mode Key Check Mode This set can display the count of errors that occurred during the recording/playing for checking. This set can check if the set and remote commander function normally. • Setting method of sound skip check result display mode 1. Set the test mode (see page 13). 2. Press the N key or [REC] key, and the playing or recording sound skip result display mode becomes active respectively where the LCD displays the following.
MZ-NF810/NF810CK SECTION 5 ELECTRICAL ADJUSTMENTS Outline • In this set, automatic adjustment of CD and MO can be performed by entering the test mode. However, before starting automatic adjustment, the memory clear, power supply adjustment, and laser power check must be performed in the manual mode. • A key having no particular description in the text, indicates a set key. • For the LCD display, the LCD on the remote commander is shown, but the contents of LCD display on the set are same. 2.
MZ-NF810/NF810CK • Adjustment Method of VC1_LOW (PB) (item number: 741) Remote commander LCD display 741 VC1 L • Adjustment Method of VC2_HIGH (item number: 744) Remote commander LCD display 744 VC2 Hi ** ** **: Adjusted value **: Adjusted value 1. Connect a digital voltmeter to the TP1928 (VCO1) on the MAIN board, and adjust [VOL +] key (voltage up) or [VOL --] key (voltage down) so that the voltage becomes 2.35 ± 0.05V. 1.
MZ-NF810/NF810CK • Adjustment Method of REG3_LOW2 (item number: 748) • Adjustment Method of VREC_MIDDLE (X4 speed) (item number: 752) Remote commander LCD display Remote commander LCD display 748 REG3L2 ** 752 VREC M ** **: Adjusted value **: Adjusted value 1. Connect a digital voltmeter to the TP1907 (REGO3) on the MAIN board, and adjust [VOL +] key (voltage up) or [VOL --] key (voltage down) so that the voltage becomes 1.25 ± 0.01V. 1.
MZ-NF810/NF810CK • Adjustment Method of CHGI_LOW (Charge Current) (item number: 757) • Adjustment Method of CHGV_LOW (item number: 755) Remote commander LCD display Remote commander LCD display 755 ChgV L ** 757 CIL ** **: Adjusted value **: Adjusted value Note: Remove the rechargeable battery. 1. Connect a digital voltmeter to the BATT+ on the MAIN board, and adjust [VOL +] key (voltage up) or [VOL --] key (voltage down) so that the voltage becomes 1.35 ± 0.01V.
MZ-NF810/NF810CK Adjustment/checking and Connection Location: MAIN BOARD (SIDE B) BATT– (GND) BATT+ (W902) 10 TP1717 TP1715 TP1905(VCOUT) 1 IC301 TP1823 * IC801 TP1524 TP1907(REGO3) TP1519 IC361 TP1930 TP1909(REGO1) TP1720 CSP(Chip Size Package) * IC501 CSP (Chip Size Package) C533 TP1909 TP1356 IC901 TP1928(VCO1) IC851 IC671 19 18 13 TP1620(VREC) 12 IC951 24 7 1 6 TP1892 1 22 IC601 15
MZ-NF810/NF810CK Power Supply Adjustment Auto Item Feed Note: This mode is available to perform the temperature correction and power supply adjustment without entering the manual mode. • Setting method of power supply adjustment auto item feed mode. 1. Set the test mode (see page 13) 2. Press the . key or press the [VOL --] key to activate the T overall adjustment mode. Remote commander LCD display 000 A s s y 5.
MZ-NF810/NF810CK Laser Power Check Overall Adjustment Mode Note: If result of measurement of the laser power does not satisfy the specification, either replace the OP (optical pick-up unit) or check whether the laser circuit block is working correctly. When the result of laser power measurement does not satisfy the specification even though the laser circuit block is confirmed to be working correctly, replace the OP (optical pick-up unit).
MZ-NF810/NF810CK • Adjustment Method of CD and MO Overall Adjustment Mode 1. Set the test mode (see page 13). 2. Press the . T key or press [VOL --] key to activate the overall adjustment mode. • Overall Adjustment error message The following message will be displayed if adjustment procedure is mistaken in the CD and MO overall adjustment. Message Display timing Description During CD/MO/DISC Remote commander LCD display CLOSE! 000 Assy11 automatic distinction DISC is not inserted.
MZ-NF810/NF810CK 2. MO overall adjustment items Item No. Item No. Description 434 TWPP gain adjustment 716 VC,VR power supply H/L selection 431 TWPP offset adjustment 1 100 R_GRV setting . servo OFF 432 TE offset adjustment 2 449 TWPP OP offset adjustment 410 READ → WRITE selection 411 TWPP offset adjustment 1 Low reflection electrical offset adjustment 112 Laser ON .
MZ-NF810/NF810CK Remuse Clear Perform the Resume clear when all adjustments completed. • Resume Clear Setting Method 1. Select the manual mode of the test mode, and set item number 043 (see page 14). Remote commander LCD display 043 Resume 00 2. Press the X key. Set LCD display 043 Res*** r Resume clear complete 043 ResClr 3. Press the xCANCEL/CHG key to return to the test mode (display check mode).
MZ-NF810/NF810CK Rewriting the Patch Data at Replacement of Main Board (IC851) This set requires the patch data in the nonvolatile memory (IC851) to be rewritten using the application, when the MAIN board was replaced. Caution: The application that meets the microcomputer version in this set must be used when rewriting the patch data. Rewriting the patch data using the application not suitable for the microcomputer version could cause the set to malfunction.
MZ-NF810/NF810CK 5. Confirm that the model and version indicated on the title bar coincide with the codes displayed in the Device Name block and the Version block in the window. 6. Click the [Write + Read] button. The patch data writing and the verify processing will be executed automatically in the following order: 1) Writing to patch area (front area) 2) Writing to patch area (reverse area) 3) Verifying patch area (front area) 4) Verifying patch area (reverse area) 7.
MZ-NF810/NF810CK • Confirmation of contents of the patch data rewrited 1. Click the [READ] button to confirm the contents of the patch data rewrited. 2. The application reads out the front and reverse patch areas and displays the results in the edit box. Confirm that the upper column coincides with the lower column as the following window. 3. Click the [OK] button to close the window.
MZ-NF810/NF810CK • Disconnecting the USB cable Disconnect the USB cable as the following procedure after rewriting the patch data and confirmation. Note : When the following procedure is not completed but USB cable is extracted, the application does not recognize the set at exchanging of the set. 1. Click the [USB DISCONNECT] button. 2. Confirm that "You can change another device" is displayed in the message block. 3. Disconnect the USB cable from the personal computer and the set.
MZ-NF810/NF810CK Rewriting the NV values Caution: The application that meets the microcomputer version in this set must be used when rewriting the NV values. Rewriting the NV values using the application not suitable for the microcomputer version could cause the set to malfunction. For a checking method of the microcomputer version, see “SECTION 4 TEST MODE” (page 13). • Preparation 1. USB cable (attached to the set) 2. Personal computer in which the Net MD Driver has been installed.
MZ-NF810/NF810CK 5. Confirm that the model and version indicated on the title bar coincide with the codes displayed in the Device Name block and the Version block in the window. 6. Click the [Write + Verify] button.
MZ-NF810/NF810CK 7. The operation will terminate with “Compere OK” given to all areas. If “Compere NG” is given to any area, the nonvolatile memory will be faulty. 8. Click the [USB DISCONNECT] button.
MZ-NF810/NF810CK 9. Confirm that the window becomes as shown below where the [Write + Verify] button is inactive. 10. Disconnect the USB cable from the personal computer and the set.
MZ-NF810/NF810CK MEMO 36
MZ-NF810/NF810CK SECTION 6 DIAGRAMS 6-1.
MZ-NF810/NF810CK 6-2. • Waveforms Note For Printed Wiring Board And Schematic Diagrams Note on Printed Wiring Board: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. • : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side) Parts on the pattern face side seen from the pattern face are indicated.
MZ-NF810/NF810CK 6-3. • Semiconductor Location 2 3 :Uses unleaded solder.
MZ-NF810/NF810CK 6-4. Printed Wiring Board – MAIN Board (Side B) – 1 2 3 :Uses unleaded solder. 4 5 6 7 8 9 10 • Semiconductor Location 11 Ref. No. MAIN BOARD (SIDE B) A 1 U N S801 M602 (SLED) (HALF LOCK) W B V M RECHARGEABLE BATTERY NH-10WM 1.
MZ-NF810/NF810CK Schematic Diagram – MAIN Board (1/4) – • See page 38 for Waveforms. • See page 47 and 49 for IC Block Diagrams. 44 43 43 44 Q604 MCH6616-TL-E C630 0.1 B C631 W602 47 4V Q605 CPH5614 B 0.1 TP1616 C616 0.1 B C617 0.1 B C671 C615 0.1 W601 R612 2.2 R613 D606 MA2YD1700LS0 C632 100p D607 MA2YD1700LS0 2.2 C626 22 6.3V TP610 C618 0.1 B Q603 TS8K1TB TP1620 C622 0.1 B C623 IC601 XPC18A22AEPR2 C624 0.01 100p R616 B CH 2.2k C621 0.
MZ-NF810/NF810CK Schematic Diagram – MAIN Board (2/4) – • See page 38 for Waveforms. • See page 45 for IC Block Diagrams. J303 J301 J303 (HP OUT) 15P TP1881 TP1882 D101 02DZ2.4-Z(TPH3) R204 10k 0.5% C304 0.1 B R302 10k R846 100k TP1358 C340 F1 1.5A 63V C305 0.1 B R303 100k R312 1M C103 1000p B C203 1000p B C301 10 6.3V C108 F301 0.25A 125V R166 0.1 47 6.3V R364 10k C264 0.22 B C164 0.22 B TP1354 TP1207 L303 R164 10k C207 47 4V R163 C312 C311 0.1 10 F 6.
MZ-NF810/NF810CK • See page 38 for Waveforms. • See page 50 for IC Block Diagrams. RADIO ON Schematic Diagram – MAIN Board (3/4) – R824 470k 10k 4.7k C841 1000p B R856 R835 TP1844 4.7k S801 TP1842 R833 R834 R836 22 TP1846 TP1839 22 R829 R828 TP1845 TP1835 TP1836 TP1837 TP1834 TP1833 TP1838 0 TP1829 TP828 TP826 TP827 TP824 TP825 R823 22 TP1868 X802 48MHz TP1831 R858 0 R827 4.7k R842 C819 1000p B TP1830 R825 1M 470k R826 2.
MZ-NF810/NF810CK Schematic Diagram – MAIN Board (4/4) – • See page 38 for Waveforms. • See page 46 and 48 for IC Block Diagrams. C524 1 B C517 0.01 B R511 0 B C518 10k R505 TP1540 TP518 0.01 R504 SL502 10k C513 0.022 B TP1539 SL501 C718 0.1 F CN501 20P C535 1 B C526 0.047 B TP1504 C720 0.1 F TP1711 TP1507 TP1712 TP1506 TP1505 TP1548 C506 0.01 B TP1522 C536 TP1510 TP1523 B TP1537 TP1511 TP1520 TP1512 TP1524 0.1 C537 0.
MZ-NF810/NF810CK • IC Block Diagrams PREOR PRENR PRER PREL PRENL PREOL MICL IC301 AK5356VN-N 21 20 19 18 17 16 15 MICR 22 14 PDN Pre-Amp Control Register I/F MVDD 23 MVSS 24 MIC Power Supply MVCM 25 MRF 26 MPWR 27 13 CSN 12 CCLK 11 CDTI 10 LRCK Audio I/F Controller ADC 9 MCLK 8 BCLK 6 7 SDTO 5 DVSS VCOM 4 AVSS 3 AVDD 2 RIN 1 DVDD LIN 28 BEEP IN GND VREF IN 18 17 16 15 14 13 PW SW MT SW BST SW BEEP STB MUTE BST SW IC361 TA2131FL (EL) 12 VREF V RE
MZ-NF810/NF810CK IY JY JX AVCC C B A D PEAK BOTM TON-C OFTRK NPPO TE IC501 SN761058ZQLR 56 55 54 53 52 51 50 49 48 47 46 45 44 43 AVCC PEAK/ BOTM OFTRK T-ON IX 1 42 FE ABCD PS 2 41 ABCD EFM COMP.
MZ-NF810/NF810CK OUTB VRECIN2 VG HB PGND3 HA 39 38 37 36 35 34 33 VG3 VG VG2 OUTPUT SW VG2 PGND2 40 C2L PGND2 41 C2H OUTA 42 VG3 VRECIN1 IC601 XPC18A22AEPR2 32 31 30 VG2 29 VC2 VG VG3 OUTPUT SW 28 C1H 27 C1L CHARGE PUMP 1 CHARGE PUMP 2 VC VG DC IN VG VB 43 BATM 44 VG3 26 VC2 VREF BUFFER VC DC IN CONTROL VC2 VC EFM PRE DRIVER HI-BRIDGE PRE DRIVER CHARGE MONITOR X2/X4 25 VREF 24 CVREF CONTROL 23 GND CHGSW 45 CHARGE CONTROL 22 DW BT 21 DW TP DC IN RS INP2
MZ-NF810/NF810CK VI1 WI1 1 UI2 VC PWM2 CPUO2 VC OE 48 47 46 45 49 VC VC 44 43 3Phase control ch2 BIAS OE 3Phase control ch1 2 50 VG CPWO2 CPVO2 53 52 51 VC GND1 54 VG CPVO1 55 CPWO1 PWM1 56 CPUO1 UI1 IC701 SC111258EPR2 OE 42 VI2 41 WI2 40 PGNDW2 VC VG ROE VG VC PGNDW1 3 WO1 4 WMVW1 39 WO2 38 VMVW2 3Phase Pre driver ch2 5 VO1 6 PGNDUV1 7 UO1 8 37 VO2 3Phase Pre driver ch1 36 PGNDUV2 35 UO2 34 VMU2 VC VG VMU1 33 VMR2 GND 9 VG VC VMR1 10 32 RO2 H-BRIDGE
MZ-NF810/NF810CK SEQSEL WDT SCK STRB DATA HPI2 HPI1 MUTEON GND VHP1 HP1(L-CH) PGND4 HP2(R-CH) VHP2 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 (VCC) CLK 64 (VCC) SLEEP IC901 SC901580EPR2 (HP AMP) VC AMP1 CONTROL FFCLR1 1 BANDGAP REFERENCE AM2 XWAKE4 2 48 VREF 47 REGC3 XWAKE3 3 REF DAC REF1 REF2 REF3 XWAKE2 4 46 REGC2 45 REGC1 REF4 REF5 XWAKE1 5 VC2 REF1 FFCLR LVB 7 43 REGO1 VG LVB DRIVER HVB 8 44 REGI1 SERIES PASS REGULATOR1 REF3 REF2 VC2 VRMC
MZ-NF810/NF810CK 6-9. IC Pin Function Description • IC801 Pin No. CXD2680-203GA (SYSTEM CONTROLLER, DIGITAL SIGNAL PROCESSOR) Pin Name I/O Description 1 OSCI I Resonator connection terminal for the system clock (22.5792MHz) 2 OSCO O Resonator connection terminal for the system clock (22.
MZ-NF810/NF810CK Pin No. Pin Name I/O Description 51 ADDT I Data input from the external A/D converter 52 KRCK O L/R sampling clock (44.1KHz) output to the external A/D converter 53 XBCK O Bit clock (2.8224MHz) output to the external A/D converter 54 FS256 O 11.
MZ-NF810/NF810CK Pin No.
MZ-NF810/NF810CK Pin No.
MZ-NF810/NF810CK Pin No.
MZ-NF810/NF810CK Pin No.
MZ-NF810/NF810CK SECTION 7 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they may have some difference from the original one. • Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) ↑ ↑ Parts Color Cabinet's Color • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • Accessories are given in the last of the electrical parts list.
MZ-NF810/NF810CK 7-2. Chassis Section 51 MD mechanism deck (MT-MZN710-177) 59 52 53 not supplied 54 55 56 MAIN board section 58 Ref. No. 51 52 53 54 55 Part No. Description 3-237-072-11 3-249-532-01 3-237-083-01 3-245-888-01 3-245-889-01 SCREW (MD), STEP SPRING (POP UP-L), TORSION SPRING (POP UP-R), TORSION SPRING (LOCK) SPRING (LIMITER) Remark Ref. No. 56 57 58 59 57 Part No. Description X-3382-583-1 3-225-995-91 3-234-449-19 3-253-535-01 CHASSIS ASSY, SET SCREW (M1.
MZ-NF810/NF810CK 7-3. MAIN Board Section 101 102 103 104 112 111 105 110 106 108 107 109 Ref. No. 101 102 103 104 105 106 * 107 * 107 58 Part No. Description 3-245-891-01 3-245-890-01 X-3382-584-1 3-234-449-19 3-245-902-01 TERMINAL (–), BATTERY CASE, BATTERY TERMINAL (+) ASSY, BATTERY SCREW (M1.4) COVER, INSULATING Remark 3-245-901-01 TERMINAL (SUM3) A-3683-786-B MAIN BOARD, COMPLETE (US) A-3683-790-B MAIN BOARD, COMPLETE (3CED,4CED,UK) Ref. No. Part No.
MZ-NF810/NF810CK 7-4. Mechanism Deck Section-1 (MT-MZN710-177) 301 A mechanism deck section-2 302 308 306 303 307 304 309 305 A 310 311 Ref. No. Part No. Description 301 302 303 304 305 X-3381-219-1 3-224-779-02 3-225-996-01 4-222-216-01 3-338-645-31 HOLDER ASSY SPRING, THRUST DETENT SCREW (M1.4) (EG), PRECISION PAN GEAR (SA) WASHER (0.8-2.5) 306 4-222-208-01 GEAR (SB) Remark not supplied Ref. No. Part No.
MZ-NF810/NF810CK 7-5. Mechanism Deck Section-2 (MT-MZN710-177) 358 357 365 M602 356 359 361 355 360 362 M603 354 353 364 352 351 not supplied 363 M601 351 Ref. No. Part No. Description 351 352 353 354 355 3-225-278-12 3-235-838-01 3-235-836-01 3-222-544-01 3-235-835-01 SCREW, TAPPING COVER, MOTOR GEAR (HB) GEAR (HA) GEAR (HC) 356 357 358 359 3-235-834-01 3-235-830-01 X-3379-529-4 3-225-996-07 CHASSIS PLATE, RATCHET BASE ASSY, MOTOR SCREW (M1.4) (EG), PRECISION PAN 60 Remark Ref. No.
MZ-NF810/NF810CK SECTION 8 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable • Items marked “*” are not stocked since they are seldom required for routine service.
MZ-NF810/NF810CK MAIN Part No. Description Part No. Description C527 C533 C534 C535 C536 1-164-941-11 1-164-943-11 1-164-941-11 1-125-837-91 1-125-777-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.0047uF 0.01uF 0.0047uF 1uF 0.1uF 10.00% 10.00% 10.00% 10% 10.00% 16V 16V 16V 6.3V 10V C814 C815 C817 C818 C819 1-125-891-11 1-164-935-11 1-125-837-91 1-125-777-11 1-164-937-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.47uF 470PF 1uF 0.1uF 0.001uF 10.
MZ-NF810/NF810CK MAIN Ref. No. CN701 CN871 Part No. Description Remark 1-573-350-11 CONNECTOR, FFC/FPC 10P 1-573-355-11 CONNECTOR, FFC/FPC 15P IC651 < DIODE > D101 D201 D302 D303 D605 8-719-056-72 8-719-056-72 6-500-116-01 8-719-017-58 6-500-483-01 DIODE DIODE DIODE DIODE DIODE 02DZ2.4-Z(TPH3) 02DZ2.4-Z(TPH3) NNCD6.8H-T1 MA8068-TX MA22D2800LS0 D606 D607 D652 D653 D654 8-719-081-35 8-719-081-35 8-719-081-73 6-500-483-01 8-719-421-27 DIODE DIODE DIODE DIODE DIODE MA2YD1700LS0 MA2YD1700LS0 DF3A6.
MZ-NF810/NF810CK MAIN Ref. No. Part No. Description Remark < RESISTOR > Description 1-218-990-11 1-218-990-11 1-218-965-11 1-216-789-11 1-216-789-11 SHORT CHIP SHORT CHIP RES-CHIP METAL CHIP METAL CHIP 0 0 10K 2.2 2.2 Remark 5% 5% 5% 1/16W 1/10W 1/10W R614 R616 R617 R619 R651 1-218-985-11 1-218-957-11 1-218-965-11 1-218-969-11 1-216-864-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP 470K 2.
MZ-NF810/NF810CK MAIN Ref. No. Part No. Description R836 R837 R838 R839 R842 1-218-985-11 1-218-973-11 1-218-957-11 1-218-990-11 1-218-990-11 RES-CHIP RES-CHIP RES-CHIP SHORT CHIP SHORT CHIP 470K 47K 2.
MZ-NF810/NF810CK Part No.
MZ-NF810/NF810CK MEMO 67
MZ-NF810/NF810CK REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date 1.0 2003.
