INSTALLATION MANUAL SFM2 Sony Electronics, Inc. 16540 West Bernardo Drive San Diego, CA 92127 www.sony.com IN-SFM2.
SFM2 Table of Contents WARNING STATEMENTS....................................................................................................................................... - 3 PARTS LIST ............................................................................................................................................................. - 4 INSTALLATION TOOLS ..........................................................................................................................................
SFM2 Warning Statements WARNING: THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE (5) TIMES THE WEIGHT OF THE DISPLAY. IF NOT, THE WALL STRUCTURE MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH. WARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT.
SFM2 Parts List NOTE: This wall mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Sony Electronics (877) 350-3477.
SFM2 Installation Procedures Check that you have all the hardware listed in the parts list (Page 5). If any of the hardware described is missing, do not continue. Contact Sony Electronics immediately at (877) 350-3477. Separate the plates and choose the location for the monitor and follow any precautions listed in the LCD owners’ manual. Single Stud Installation 1. 2. 3. 4. For single wood studs, use the two middle mounting points found on the back plate (Figure 1).
SFM2 Solid Structure Installation 1. 2. 3. 4. Use the four mounting points on the back plate (Figure 2). Choose the wall where the monitor will be located. Level and mark with a pencil the four (4) mounting points found on the back plate. Drill four (4) 1/4" pilot holes for the plastic anchors then secure the wall bracket with the four (4) #10 x 1¼" screws (supplied) to the anchors. NOTE: All electrical wiring should be done at this time.
SFM2 Attaching the Adapter Plate and the Backplate Cover 1. 2. 3. 4. Line up the mounting points (Figure 3). Attach the frontplate to the adapter plate using four (4) M4 x 10mm Phillips Head screws (Figure 4). Do not tighten the screws until all four are inserted. Once the screws are inserted, tighten the screws down. CAUTION: Do not over tighten the M4 screws to the monitor. Failure to do so could result in damaging the threads and monitor. 5.
SFM2 Adapter Plate M4 x 10mm Phillips Head Screws M4 x 10mm Phillips Head Screws Frontplate M6 x 12mm Phillips Head Security Screws Figure 4 Page - 8 - Installation Instructions
SFM2 Attaching the Adapter Plate /Backplate Cover to the Display 1. Place the display on a flat and soft surface and locate the four mounting points (Figure 5). 2. Attach the Adapter Plate to the back of the display using four (4) M6 x 10mm Phillips Head screws (Figure 6). Do not overtighten the screws. CAUTION: DO NOT OVERTIGHTEN THE SCREWS. Figure 5. Installing the Adapter Plate/ Mounting Box Adapter Plate Ultra Flat Mount Figure 6.
SFM2 Attaching the Display to the Backplate NOTE: 1. 2. 3. 4. For clarity purposes, the following illustrations will be shown without the adapter plate and display attached. This must be done to show how the positioning of the backplate cover and the backplate relate to each other (connection-wise). The flange opening must be facing up. Raise the flat panel with the front plate attached and slide the top flange opening to the flange on the backplate (Figure 7). Slide the monitor down slowly.
SFM2 Technical Specifications Figure 7. Adapter Plate VESA 100 VESA 75 .750" 4.750" 5.3125" 5.750" Figure 8.
SFM2 Warranty Limited Lifetime Warranty This product carries a limited lifetime warranty from ship date against defects in materials and workmanship. Sony Electronics is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury. Customer Support In the event of missing and/or damaged equipment, or technical questions, the following information can help in the completion of the installation.
