TFT LCD Color Computer Display SDM-HX73 SDM-HX93 © 2003 Sony Corporation
Owner’s Record The model and serial numbers are located at the rear of the unit. Record these numbers in the spaces provided below. Refer to them whenever you call upon your dealer regarding this product. Serial No. Model No. WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Dangerously high voltages are present inside the unit. Do not open the cabinet. Refer servicing to qualified personnel only.
Table of Contents Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Identifying parts and controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Setup 1: Connect the video signal cables . . . . . . . . . . . . . . . . . . . . 7 Setup 2: Connect the audio cord . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Setup 3: Connect the power cord . . . . .
Note on the LCD (Liquid Crystal Display) Precautions Warning on power connections • Use the supplied power cord. If you use a different power cord, be sure that it is compatible with your local power supply. For the customers in the U.S.A. If you do not use the appropriate cord, this monitor will not conform to mandatory FCC standards. For the customers in the UK If you use the monitor in the UK, be sure to use the appropriate UK power cord.
A 1 (Power) switch and 1 (power) indicator (pages 9, 19, 24) To turn the display on or off, press the 1 (power) switch. The power indicator lights up in green when the display is turned on, and lights up in orange when the display is in the power saving mode. Identifying parts and controls See the pages in parentheses for further details. Front of the LCD display B Light sensor (page 20) This sensor measures the brightness of the surrounding area. Be sure not to cover the sensor with papers, etc.
K AC IN connector (page 8) This connector connects the power cord (supplied). Rear of the LCD display L Security Lock Hole The security lock hole should be used with the Kensington Micro Saver Security System. Micro Saver Security System is a trademark of Kensington. ql qa qd qf INPUT 1 N HD15 input connector (analog RGB) for INPUT1 (page 7) This connector inputs analog RGB video signals (0.700 Vp-p, positive) and sync signals.
Setup Before using your monitor, check that the following items are included in your carton: • LCD display • Power cord • HD15-HD15 video signal cable (analog RGB) • DVI-D video signal cable (digital RGB) • Audio cord (stereo miniplug) • CD-ROM (utility software for Windows/Macintosh, Operating Instructions, etc) • Warranty card • Quick Setup Guide Connect a computer equipped with a DVI output connector (digital RGB) Using the supplied DVI-D video signal cable (digital RGB), connect the computer to the mon
x Connecting to a Macintosh Setup 3: Connect the power cord 1 Connect the supplied power cord securely to the monitor’s AC IN connector. 2 Connect the other end securely to a power outlet. to the HD 15 input connector (analog RGB) 1 to AC IN to the computer’s output connector HD15-HD15 video signal cable (analog RGB) (supplied) Macintosh 2 power cord (supplied) When connecting a Macintosh computer, use an adapter (not supplied), if necessary.
Setup 4: Bundle the cords and cables Setup 5: Turn on the monitor and computer 1 Slide up the back cover. 1 2 Secure the video signal cable, audio cords and the power cord using the cable holder on the cabinet. 3 Slide down the back cover. Press the 1 (power) switch on the front of the monitor. The 1 (power) indicator lights up in green. MENU lights in green OK INPUT 1 back cover 2 3 2 Turn on the computer. 3 Press the INPUT button to select the desired input signal.
If no picture appears on your screen • Check that the power cord and the video signal cable are properly connected. • If “NO INPUT SIGNAL” appears on the screen: – The computer is in the power saving mode. Try pressing any key on the keyboard or moving the mouse. – Check that the input signal setting is correct by pressing the INPUT button (page 11). • If “CABLE DISCONNECTED” appears on the screen: – Check that the video signal cable is properly connected.
Selecting the input signal (INPUT button) Press the INPUT button. The input signal change each time you press this button. INPUT On-screen message (Appears about 5 seconds on the upper left corner.
4 Customizing Your Monitor Before making adjustments Adjust the item. Press the m/M buttons to make the adjustment, then press the OK button. When you press the OK button, the setting is stored, then the display returns to the previous menu. Connect the monitor and the computer, and turn them on. For the best results, wait for at least 30 minutes before making adjustments. OK , You can make numerous adjustments to your monitor using the on-screen menu. Navigating the menu 1 Display the main menu.
