User Manual

86
Setup Menu
Chapter 7 Menus
807 AUDIO OUTPUT PHASE Set the output timing of digital audio playback signals (HDSDI, SDI, AES/
EBU only) as a hexadecimal value, with 80 as a reference position.
Output timing is earlier for values smaller than 80 and later for values
greater than 80. (80, 128 samples = approx. 2.7 ms, 80, 1 sample =
approx. 20 μs)
0 to 80
to FF: Values can be set in this range.
808 INTERNAL AUDIO SIGNAL
GENERATOR
Select the operation of the internal audio test signal generator.
off: Do not output test signal.
silence [silnc]: Silent signal
1kHz sine [1kHz]
: 1 kHz, –20 dB FS sine wave signal
When you set the INT SG item on page P1 INPUT of the function menu
to “ON”, the internal signal generator operates and outputs simultaneous
test signals to channels 1 to 8 (see page 35).
823 NON-AUDIO FLAG PB Control non-audio flags in digital audio output.
Sub-item
1 CH1/CH2 During playback (except in EE mode), set non-audio flags in digital audio
output to the following states.
on: Set to on (data is non-audio.)
auto
: Set as follows.
• When data is read from media and confirmed: Follow the media.
• When data from media is not confirmed: Maintain current state.
2 CH3/CH4
3 CH5/CH6
4 CH7/CH8
824 ANALOG LINE OUTPUT SELECT Select the analog audio signals (tracks 1 to 8) to be assigned to audio
output channels 1 and 2.
tr1/2
: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
828 SDI AUDIO OUTPUT SELECT Select the audio signals to assign to SDI audio output channels.
Sub-item
1 CH1/CH2 tr1/2
: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
2 CH3/CH4 tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4.
tr3/4
: Tracks 3 and 4 assigned to audio output channels 3 and 4.
tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4.
tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4.
Menu items in the 900s, relating to digital process
Item number Item name Settings
920 SD-SDI H-ANC CONTROL
a)
Select whether to add information to the SDI output.
Sub-item
1 AUDIO 5CH-8CH off: Do not add digital audio data channels 5 to 8.
on
: Add digital audio data channels 5 to 8.
2 RP188 ATC off: Do not add RP188 timecode data.
on
: Add RP188 timecode data.
925
HDMI OUTPUT SELECT
a)
Select the resolution of the video output from the HDMI OUT connector.
1080i
, 480i, 480P (59.94i, 29.97P mode)
1080i, 576i, 576P (50i, 25P mode)
720P
, 480i, 480P (59.94P mode)
720P
, 576i, 576P (50P mode)
930 DOWN CONVERTER MODE
a)
Select the down-converter mode.
EDGE CROP [CROP]: Select the edge crop mode.
LETTER BOX [L-BOX]: Select the letter box mode.
SQUEEZE [SQUEZ]: Select the squeeze mode.
Menu items in the 800s, relating to audio control
Item number Item name Settings