User Manual

35
Basic Operations of the Function Menu
Chapter 3 Preparations
a) This is displayed only when TCG on page P4 TC of the function menu is
set to “INT”, and PRST/RGN is set to “PRESET”.
P1 INPUT page
P2 INPUT page
P3 AUDIO page
F5: MONITR R Selects the channel to monitor as the right
monitor channel.
CH1, CH2
, CH3, CH4, CH5, CH6, CH7,
CH8
CH1/2, CH3/4, CH5/6, CH7/8 (MIX)
F6: OUT REF Selects the reference signal for the output
signals of this unit.
REF
: Use the signal input to the REF.
VIDEO INPUT connector as the output
reference signal.
INPUT: Use the input video signal as the
output reference signal.
Item Setting
F1: INT SG Set whether to select test signal from
internal signal generator.
OFF
: Do not select.
ON: Select.
F2: V INPUT Selects the video input signal.
HDSDI
: HDSDIsignal
SDSDI: SDSDI signal
Notes
• Test signal is input when INT SG on this
page is set to “ON” and setup menu item
710 is set to anything other than “Off”.
• When the system frequency is 23.98P, the
setting is fixed “HDSDI”.
F3: A1 INPUT Selects the audio input signal to assign to
audio channel 1.
SDI
: Audio signal embedded into SDI signal
ANALOG1: Input signal to the ANALOG
AUDIO INPUT 1 connector
Note
Test signals are input to all audio channels
1 to 8 when INT SG on this page is set to
“ON” and setup menu item 808 is set to
anything other than “off”.
F4: A2 INPUT Selects the audio input signal to assign to
audio channel 2.
SDI
: Audio signal embedded into SDI signal
ANALOG2: Input signal to the ANALOG
AUDIO INPUT 2 connector
F5: A3 INPUT Selects the audio input signal to assign to
audio channel 3.
SDI
: Audio signal embedded into SDI signal
ANALOG1: Input signal to the ANALOG
AUDIO INPUT 1 connector
F6: A4 INPUT Selects the audio input signal to assign to
audio channel 4.
SDI: Audio signal embedded into SDI signal
ANALOG2: Input signal to the ANALOG
AUDIO INPUT 2 connector
Item Setting
Item Setting
F1: A5 INPUT Selects the audio input signal to assign to
audio channel 5.
SDI
: Audio signal embedded into SDI
signal
ANALOG1: Input signal to the ANALOG
AUDIO INPUT 1 connector
F2: A6 INPUT Selects the audio input signal to assign to
audio channel 6.
SDI
: Audio signal embedded into SDI
signal
ANALOG2: Input signal to the ANALOG
AUDIO INPUT 2 connector
F3: A7 INPUT Selects the audio input signal to assign to
audio channel 7.
SDI
: Audio signal embedded into SDI
signal
ANALOG1: Input signal to the ANALOG
AUDIO INPUT 1 connector
F4: A8 INPUT Selects the audio input signal to assign to
audio channel 8.
SDI
: Audio signal embedded into SDI
signal
ANALOG2: Input signal to the ANALOG
AUDIO INPUT 2 connector
F5: SPEAKER Sets whether or not the built-in speakers
produce output.
OFF
: Not produce output.
ON: Produce output.
F6: – (Unassigned function button)
Item Setting
F1: A5 VOL Sets the volume of audio channel 5.
a)
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to
+12 dB) by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F2: A6 VOL Sets the volume of audio channel 6.
a)
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to
+12 dB) by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F3: A7 VOL Sets the volume of audio channel 7.
a)
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to
+12 dB) by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.