PCG-FXA53/FXA59 SERVICE MANUAL For American Area US Model CanadianModel Ver 2-2002G Revision History l a i t n Lineup : PCG-FXA59 PCG-FXA53 S400 e d i f n o C • Design and specifications are subject to change without notice.
Information in this document is subject to change without notice. Caution Markings for Lithium/Ion Battery - The following or similar texts shall be provided on battery pack of equipment or in both the Sony, VAIO and CLIE are trademarks or registered trademarks of Sony. Microsoft, Windows, Windows Media, Outlook, Bookshelf operating and the service instructions. and other Microsoft products are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries.
TABLE OF CONTENTS Section Title Page CHAPTER 1. BLOCK DIAGRAM ............................... 1-1 (to 1-2) CHAPTER 2. FRAME HARNESS DIAGRAM ........ 1-1 (to 1-2) CHAPTER 3. EXPLODED VIEWS AND PARTS LIST ............................................ 3-1 3-1. Main Section .................................................................... 3-2 3-2. FDD Section .................................................................... 3-5 3-3. LCD Section (FXA53 Model) – Made by AC – .............. 3-7 3-3-A.
CHAPTER 1. BLOCK DIAGRAM CPU PCG-FX Series AMD Mobile Athlon XP 1500 + BLOCK DIAGRAM Rev.A (Cache:128KB L1 256KB L2) (FSB 200 MHz) w/ Port Replicator (PCGA-PRFX1) LCD Panel XGA ADDRESS DATA CTRL SIGNAL 256MB X1 (Max.512MB) Socket 1 Socket 2 Main Memory PC133 SO-DIMM PC Card 14.
CHAPTER 2. FRAME HARNESS DIAGRAM DC-IN USB MONITOR NETWORK PRINTER SERIAL USB PHONE Rear Panel LCD KEY BOARD INVERTER DC FAN FFC LED CON5 CPU1 IEEE 1394 i.
CHAPTER 3. EXPLODED VIEWS AND PARTS LIST NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “ * ” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • When two or more parts are shown in parallel, use the part described first as the main part. • The indication [CH] is used for identification of part type.
3-1. Main Section Ref.No. 1 3 *8 11 15 Part No. X-4623-848-3 4-640-837-22 4-651-706-01 4-656-752-01 4-643-832-21 Description [CH]...ASSY BOTTOM (Q) DOOR BATTERY HEATSINK BOTTOM [CH]...INSULATOR HEATSINK BOTTOM DUMMY CARD Ref.No. 161 162 163 164 165 Part No.
B8 B1 B33 B33 J 187 181 185 186 B1 I B1 B1 22 J 30 B32 B15 N A N 25 K B1 B15 M 60 19 188 B1 B8 24 164 B1 182 Supplied with 88 88 63 18 76 Supplied with 88 B8 H 28 29 123 B4 20 B4 I K 194 195 76 H B8 149 148 162 72 B4 B8 157 F 46 125 124 136 M B8 26 20 166 B17 B8 27 B14 136 180 147 15 196 C Supplied with 19 L B7 L C B1 71 B10 78 197 193 D B38 Supplied with 88 165 B10 31 B8 161 B12 191 192 B8 81 84 52 48 134 B8 B B3 A 163 162
MEMO 3-2. FDD Section How to use properly the FDD repair parts. Types of service to be provided are different depending on the part No. of the FDD in use. Label FD X-XXX-XXX-XX Label Part No. The service types are shown below depending on the part No. that is printed in the bottom right of the FD label. [Label Part No. : 4-656-805-0*] [Label Part No. : 4-641-763-3*] 800 800 806 807 804 801 805 802 B1 803 B1 Ref.No. Part No. Description 800 A-8025-674-A FDD UNIT ASSY (TN-CH) Ref.No.
3-3. LCD Section (FXA53 Model) – Made by AU – 303 Ref.No. 301 302 303 304 305 Part No.
3-3-A. LCD Section (FXA59 Model) – Made by SH – 424 426 424 B22 434 403 B30 435 424 406 B22 434 408 421 Supplied with 403 B22 424 423 Ref.No. 401 402 403 406 407 Part No.
3-4. Connector Section (CH Type only) Ref.No. 901 Fig. Part No. Description 1-779-745-21 [CH]...JACK, DC DC IN connector 902 9-885-018-97 [CH]...CONNECTOR (1.2MM), USB USB connector Bracket I/O 903 902 901 9-885-018-98 [CH]...CONNECTOR (1.6MM), USB USB connector ∗ Among the parts that are used on the boards of this model, only the connectors that are show in the list can be replaced. (The parts other that the specified connectors cannot be replaced.
CHAPTER 4. OTHERS 4-1. Replacing the CPU Fig. Part No. Description J-2507-309-1 JIG FOR COU 1. Removing the CPU 3 5 2 1 6 4 1 Install the special tool in the CPU. 2 Insert a flat head (-) screwdriver tip into the groove as shown. 3 While holding the special tool, slant the screwdriver in the direction of the arrow. 4 The base under the CPU moves slightly in the direction of the arrow and the CPU lock is released. 5 Remove the special tool. 6 The CPU can be removed upward. 2.
PCG-FXA53/FXA59 (AM) List of PCG-FX Series (As of July, 2002) Model Name Service Manual Part No.
Revision History Suffix Ver. Date -01 Ver. 1 2002.04.26 -02 Ver. 2 2002.07.01 Contents QM No.
