NSR-1000 Series NSR-1200/NSR-1100/NSR-1050H Version 1.1.1 Release Note 1st Edition Last Modified Date: Dec.
Copyright Notice ©2009 Sony Corporation. All rights reserved. This document may not be reproduced, translated or reduced to any machine readable form in whole or in part, without prior written approval from Sony Corporation. SONY CORPORATION PROVIDES NO WARRANTY WITH REGARD TO THIS DOCUMENT OR INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO THIS DOCUMENT OR SUCH INFORMATION.
Index １ Overview...............................................................................................................................1 １-１ Additional features by v1.1.1 ......................................................................................1 １-１-１ Multiple Codecs support .....................................................................................1 １-１-２ Simple Motion Detection support.......................................................................1 １-１-３ H.
４-１-３ Main Window - Search and Play back..............................................................19 ４-１-４ Main Window – Monitoring ..............................................................................20 ４-１-５ Analog Camera Control ....................................................................................21 ４-１-６ Alarm Notification / Alarm History..................................................................22 ４-１-７ Search Window....................................................
NSR-1000 Series v1.1.1 Release Note １ Overview This release note provides the information for the software of the NSR-1200 / NSR-1100 / NSR-1050H. For the built-in NSR Client (IMZ-NS Series) software, please refer to the release note of the RealShot Manager Advanced included in the client software. １-１ Additional features by v1.1.1 １-１-１ Multiple Codecs support Newly supports multiple codecs for Sony IP network cameras and camera servers shown below. IP network camera (max.
NSR-1000 Series v1.1.1 Release Note SNC-RX570 v3.10/2.40 or higher SNC-CS50 v2.30 or higher SNC-RZ50 v2.40 or higher SNC-DF50 v1.20 or higher SNC-DF80 v1.20 or higher SNC-DF85 v1.20 or higher １-１-４ Expansion of supported languages Newly supports Polish and Korean. １-２ Built-in client software and software tools with NSR-1000 Series NSR-1000 NSR Server Software NSR Client* [RealShot Series Version Version Manager Advanced (Client)] Media File Player Version Version V1.0.0 1.0.0.26 1.
NSR-1000 Series v1.1.1 Release Note V1.0.0 1.0.0.26 1.0.0.16 1.2.0.7 V1.0.1 1.0.1.4 1.0.1.4* 1.2.0.11 V1.0.4 1.0.4.6 1.0.4.6* 1.2.1.5 V1.1.0 1.1.0.20 1.1.0.19 1.2.2.4 V1.1.1 1.1.1.7 1.1.1.7 1.2.3.0 *New RealShot Manager Advanced is planned to be released. Please refer to the release note for the RealShot Manager Advanced and Media File Player which are included with RealShot Manager Advanced.
NSR-1000 Series v1.1.1 Release Note １-４ Support Camera Information Sony Camera Model Name Camera Firmware Version SNC-CM120 v1.02 or higher SNC-CS3 v1.08 or higher SNC-CS10 v1.06 or higher SNC-CS11 v1.06 or higher SNC-CS20 v1.02 or higher SNC-CS50 v2.24 or higher SNC-DF40 v1.18 or higher SNC-DF50 v1.15 or higher SNC-DF70 v1.18 or higher SNC-DF80 v1.15 or higher SNC-DF85 v1.15 or higher SNC-DM110 v1.02 or higher SNC-DM160 v1.02 or higher SNC-DS10 v1.02 or higher SNC-DS60 v1.
NSR-1000 Series v1.1.1 Release Note SNC-Z20 v1.06 or higher SNT-EP104 v1.04 or higher SNT-EP154 v1.04 or higher SNT-EX101 v1.04 or higher SNT-EX101E v1.04 or higher SNT-EX104 v1.04 or higher SNT-EX154 v1.04 or higher SNT-V704 v2.16 or higher Axis Camera Model Name Camera Firmware Version Axis 206 v4.40 Axis 207 v4.40 Axis 207W v4.40.1 Axis 210 v4.40 Axis 210A v4.40.1 Axis 211 v4.40 Axis 211A v4.30 Axis 221 v4.45 Axis 209FD v4.47 Axis 209FD-R v4.47 Axis 209MFD v4.
NSR-1000 Series v1.1.1 Release Note Axis 214PTZ v4.40 Axis 215PTZ v4.40 Axis 232D+ v4.41 Axis 233D v4.48.1 Axis 241Q v4.30 Axis 241QA v4.30 Axis 241S v4.40 IQinVision Camera Model Name Camera Firmware Version IQeye510 v2.8/6(080313) IQeye511 v2.8/6(080313) IQeye702 v2.8/6(080313) IQeye703 v3.0/2(090521) IQeye705 v3.0/2(090521) IQeye711 v3.0/2(090521) IQeye752 v3.0/2(090521) IQeye753 v3.0/2(090521) IQeye755 v3.
NSR-1000 Series v1.1.1 Release Note ２ Important notes ・ The cameras and camera servers listed below have some restrictions at V1.04 firmware. SNC-RH series SNC-RS series SNT-EP series SNT-EX series The following are planned to be solved in a future release (V.1.06 or later). ・ Periodical sending of VMF metadata is not executed.(V11N:520, V11R:735) ・ After the execution of pan /tilt operation, notification of motion detection alarm is no longer issued.
NSR-1000 Series v1.1.1 Release Note ３ Notes ３-１ Installation / System Configuration ・ The NSR-1000 Series cannot connect with the client if the setting for ‘Network Interface for Remote Client’ on the ‘Server Configuration’ is configured as ‘Network3’. Please set ‘Network1’ or ‘Network2’. (VT1:2036) ・ If user changes the time zone setting on the ‘Setup Menu’ in the middle of operation such as schedule recording, scheduled recording setting or scheduled action setting change.
NSR-1000 Series v1.1.1 Release Note NTSC Resolution Maximum CIF(352x240) 480 2CIF(704x240) 240 4CIF(704x480) 120 frame rate PAL Resolution Maximum frame rate CIF(352x288) 400 2CIF(704x288) 200 4CIF(704x576) 100 ・ User cannot change parameters about recording settings of analog cameras in the ‘Schedule Configuration’. Please change setting in ‘Video’ tab on ‘Device Configuration’. These parameters are used as recording settings for ‘Schedule Configuration’.
NSR-1000 Series v1.1.1 Release Note ・ "Smooth Scaling" function is available for only one monitor frame which is currently selected. This function is not applied to second display. (VT1:2069) ・ The DIRECT PTZ function is not supported on camera servers SNT-EX/EP series connected to analog cameras. To achieve this function, use the buttons in the Camera Control pane or the remote controller.
NSR-1000 Series v1.1.1 Release Note ・ You can select only the one check box in the search results list. Playback is enabled for the selected search result. Exporting is enabled for the selected search result, too. You can protect /unprotect the recordings if their background is turned into blue with the check box selected. (VT1:2163) ３-１０ Device Configuration This section describes precautions on use of camera or setting.
NSR-1000 Series v1.1.1 Release Note internal value not to over the limitation. (V11N:335) ・ Regarding following cameras, if user use the VMD (Camera) with the codec as MPEG4, the frame rate is limited as 20FPS with NTSC or 16FPS with PAL. If VMD (Camera) is disabled after enabled, maximum frame rate setting becomes available after other resolutions are selected once.
NSR-1000 Series v1.1.1 Release Note ・ The image size of more than QVGA(320x240) is selected, the maximum frame rate is limited at the transmission side as follows: NTSC: 10 fps or less PAL: 8 fps or less ・ If the cameras mentioned below uses the MPEG4 codec with the image size of more than 384x288, the maximum frame rate is limited at transmission side.
NSR-1000 Series v1.1.1 Release Note values different from actual ones when making configurations for the cameras/camera servers shown below (V11R:483) SNC-RH series SNC-RS series SNT-EP series SNT-EX series In this case, perform the adjustment of the detection area size while viewing on the frame in the configuration screen. ・ When parameters in the Video setting tab are changed while recording, it will affect the recording like the followings.
NSR-1000 Series v1.1.1 Release Note registration. (V11N:461) ３-１１ Action Configuration ・ N/A ３-１２ Schedule Configuration ・ If user sets the schedule record of following cameras with the ‘Automatic Record Configuration’, the codec setting shall be not MPEG4 but JPEG. If user needs to change the setting, please select the codec on ‘Video’ tab in the Device menu.
NSR-1000 Series v1.1.1 Release Note between start and stop time of recording is too long or the time displayed on the monitor frame jumps suddenly. Please change the system time after stopping to record. (VT1:1659) ・ ３-１３ User Configuration ・ If user set the username and password except English one byte characters, [-], and [_], user cannot log on with the username and the password. In this case, please log on with administrative privileges and change the username and the password.
NSR-1000 Series v1.1.1 Release Note ・ When you change the video-related options (Image Size, Image Quality and Frame Rate) on the [Video] tab while monitoring/recording a JPEG image an AXIS camera is capturing, monitoring or recording may continue with the previous settings. To enable the changed values in monitoring, be sure to logoff once, and then logon.
NSR-1000 Series v1.1.1 Release Note the value specified by “Frame rate”. It also depends on combination of image size and frame rate. (V11R:58) Before use, be sure to check whether an image is output at the specified frame rate. If not, reconfigure the image size or frame rate to the other value. It has been confirmed that this issue happens in the following combinations. Confirmed firmware version is v3.0/2 in all cases. IQeye752 (max.
NSR-1000 Series v1.1.1 Release Note ４ Limitations ４-１ Known Limitations ４-１-１ Installation / System Configuration ・ When enabling the SNMP agent function under [Administration] menu -> [Setup] menu -> [SNMP Menu] ->[Trap], the error message below is displayed and the ERROR lamp is lit. There is no problem in operation, however, because it is displayed when service automatically restarts itself.
NSR-1000 Series v1.1.1 Release Note for continuous recording, it takes more than ten minutes to load the recorded data since [PLAYBACK] is pressed. When you want to select “iSCSI” as recording storage, it is recommended to segment the record by setting a recording schedule that inserts a 1 -second recording break each day in the recurrent schedule of the normal recording. (V11N:38) e.g.
NSR-1000 Series v1.1.1 Release Note ・ When recording audio from a camera of which frame rate is set to less than 1fps, you cannot play back audio in synchronization with image. For example, in case of 0.25fps, a four-second image is played back per a frame. On the other hand, with regard to audio, a one-second audio is repeatedly played back four times per a frame. (V11N:368) ・ Using the following cameras, monitoring images stops for a several seconds just after the camera preset tour starts or stops.
NSR-1000 Series v1.1.1 Release Note ４-１-６ Alarm Notification / Alarm History ・ If user tries to play back the camera with double-clicking alarm history during playing back it on the other monitor frame, the NSR-1000 Series cannot start to play back and live image is displayed. Please make sure that the camera is not played back on other monitor frames when user starts to play back it.
NSR-1000 Series v1.1.1 Release Note selected, actual frame rate is 1fps. (VT1:1842) ・ You can change multiple registration details by selecting two or more cameras at time, if they are all the same model. If 29 or more cameras are selected, however, there are cases where the maximum value cannot be selected from the list. To work around this, select up to 28 cameras.
NSR-1000 Series v1.1.1 Release Note (V11N:363,V11N:446) In addition, when making the Device configuration settings continuously, there are infrequent cases where a part of set values etc., is not displayed by screen refresh even after the settings are applied. In this case, select another camera once in the camera tree and then reselect the target camera.
NSR-1000 Series v1.1.1 Release Note set up masks again. (V11R:484) ４-１-９ Server Configuration ・ Pay attention to the followings when you want to change the recording storage from default to other in the storage settings. It affects the estimation of storage capacity. When the storage mode is put into the camera mode (refer to “Configuring Storage for Each camera ([Camera] mode) in the User’s Guide, for details.), audio data is saved in default storage even if changing the recording storage from default.
NSR-1000 Series v1.1.1 Release Note ・ If user modifies recording settings in ‘Schedule Configuration’ such as alarm to event, the NSR-1000 Series doesn’t reload the default recording settings (codec / Image Size / Image Quality / Bit Rate / Frame Rate) on ‘Video’ tab in the ‘Device Configuration’ automatically. Please click ‘Adjust to Camera Configuration’ at the bottom of ‘Schedule Configuration’ Window and reload the last settings manually.
NSR-1000 Series v1.1.1 Release Note Otherwise, the following issues occur: -An hour is given or taken for the schedule which triggers actions. -Time indication in the alarm history is read an hour behind or early. Note that you cannot play back by clicking the alarm history where the improper time is displayed. To work around this, play it from the search results.
NSR-1000 Series v1.1.
NSR-1000 Series v1.1.1 Release Note ４-２ Resolved limitations in V1.1.1 ・ There were some restrictions in V1.02 of the cameras/camera servers below. (V11R:386,V11R:440,V11N:379) SNC-RH series SNC-RS series SNT-EP series SNT-EX series The restrictions mentioned below have been solved in V.1.04. ・ When executing the preset function, detections by VMD(Camera) and VMF don’t work. ・ Overwrite recording during the shadow tour may be disabled during a certain period.
NSR-1000 Series v1.1.1 Release Note monitor frames on the NSR even when you pressed MONITOR SELECT button. (V11N:478) This issue has been solved. ・ There was a problem that communication with the slave server was not established after you upgraded the NSR-1000 series or RealShot Manager Advanced which configured the master/slave configurations, from v1.0.4 to v1.1.0. (V11N:473, V11R:582) This issue has been solved.
NSR-1000 Series v1.1.1 Release Note ・ There was a problem that live image is not displayed depending on the video codec settings on the SNC-RH series camera. (V11R:745) This issue has been solved. Example of video codec settings that cause the trouble: H.264, 4096kbps, 1fps H.264, 8192kbps, 1fps H.264, 8192kbps, 2fps ・ When SNC-DF85 are being used with the RealShot Manager Advanced of less than v1.1.0.19 with JPEG codec and then, you upgrade it to v1.1.0.
NSR-1000 Series v1.1.1 Release Note ５ Appendix ５-１ Histories of additional features ５-１-１ Additional features by V1.1.0 ５-１-１-１ Expansion of supported cameras Newly supports the Sony IP network cameras and camera servers shown below. IP network camera: SNC-RS44, SNC-RS46, SNC-RS84, SNC-RS86, SNC-RH124, SNC-RH164 Camera server: SNT-EP104, SNT-EP154, SNT-EX101, SNT-EX104, SNT-EX154 Major new feature supported by the NSR-1000 series are as follows: ・H.
NSR-1000 Series v1.1.1 Release Note ５-１-１-４ 4CIF resolution support Newly supports 4CIF resolution (PAL: 704x576, NTSC: 704x480) for the Sony IP network cameras. Supported model name and firmware version are as follows: Camera Model Name Camera Firmware Version SNC-RX530 3.10/2.40 or higher SNC-RX550 3.10/2.40 or higher SNC-RX570 3.10/2.40 or higher SNC-CS50 2.30 or higher SNC-RZ50 2.40 or higher SNC-DF50 1.20 or higher SNC-DF80 1.20 or higher SNC-DF85 1.
NSR-1000 Series v1.1.1 Release Note ５-１-２ Additional features by V1.0.4 Object Improvement Server/Client AXIS and IQinVision cameras are supported. (VT1:2072, 2099) Client Audio Upload From a Client is supported. (VT2:728) Server/Client Specifying Camera and Server with Host Name is enabled. (VT1:2095, VT3:863) Server/Client All Monitor Frames Function on the Monitor Control pane is enabled. (VT1:2083, VT2:736) Server/Client [Close] button in the right-bottom on each configuration screen is added.
NSR-1000 Series v1.1.1 Release Note Server/Client The NSR-1000 Series and the client software start to support controlling PTZ of analog camera via VISCA protocol.
NSR-1000 Series v1.1.1 Release Note ５-２ Histories of resolved limitations ５-２-１ Resolved limitations in V1.1.0 ５-２-１-１ Main Window – Monitoring ・ There are cases where a camera does not move even if you select the preset position which is already configured and appears in the preset list. This problem may happen when you move a camera in the ways other than selecting the preset position after moving it to the present position once on the main screen.
NSR-1000 Series v1.1.1 Release Note configured before may disappear on [Camera Action] tab. After the tour settings are updated in the device menu, be sure to reconfigure [Action end preset]. (V11N:54) ・ The problem that occurs when configuring the event/alarm actions If you change target devices for the action on the right side of the screen after some conditions for event/alarm actions are changed in [Schedule] screen, the values for the alarm condition are cleared.
NSR-1000 Series v1.1.1 Release Note ５-２-２ Resolved limitations in V1.0.4 ５-２-２-１ Installation / System Configuration ・ When saving the system configuration information in Control Menu, the prohibited characters such as ＃,＄,％ can be used in the file name. However, you should not use those characters, because it is not possible to save it when using them.
NSR-1000 Series v1.1.1 Release Note ・ GUI abends at login when logoff while the alarm history panel is folded at main monitoring window. (VT1:2188) ・ Play back audio is not available under the following conditions. (VT1:1906) ・ The layout is changed to 1x1 with the monitor frame double-clicked during playing back. Please click ‘PLAYBACK’ button to restart after clicking ‘LIVE’ button once. ・ If user clicks ‘LIVE’ button during playing back at 1x1 layout, the NSR-1000 Series cannot make a sound.
NSR-1000 Series v1.1.1 Release Note window, a space can not be used in the Preset name. (VT1:1960) ・ When VMD(Camera) is configured to SNT-V704, the detection area is created as QVGA size even though the detection area is configured as the full screen of the monitor frame. (VT1:2032) ・ When the multiple cameras are selected in Device configuration, all the sensor input/output pins of the selected cameras are shown instead of the common sensor input/output pins among the selected cameras.
NSR-1000 Series v1.1.1 Release Note ５-２-２-６ Action Configuration ・ When the schedule action is set, the camera preset setting might not be correctly preserved. (VT1:2177) ５-２-２-７ Search Window ・ During the playback for the multiple cameras in the timeline view, the synchronization among the multiple cameras takes time when moving the slide bar.
NSR-1000 Series v1.1.1 Release Note ５-２-３ Resolved limitations in V1.0.1 ・ There was a possibility that some recording frames were lost if the NSR-1000 Series with the NSRE-S200 was carried out over long periods with overwriting. (VT1:1585) ・ NSR-1000 Series could not display correct time on the monitor when below time zones were selected. GMT -0,-1,-3,-9,+9:30,+12 (VT1:1953) ・ The Media File Player could not convert Megapixel images to AVI format when these images were exported with it.
