CAUTION Owner’s Record The model and serial numbers are located at the rear of the projection TV, below the Sony logo, on the sticker, and also on the TV box (white label). Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. Serial No._______________________ WARNING To prevent fire or shock hazard, do not expose the projection TV to rain or moisture.
❑ ❑ ❑ ❑ Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your warranty and your authority to operate this equipment.
IMPORTANT SAFEGUARDS For your protection, please read these instructions completely, and keep this manual for future reference. Carefully observe and comply with all warnings, cautions and instructions placed on the set or described in the operating instructions or service manual. WARNING To guard against injury, the following basic safety precautions should be observed in the installation, use and servicing of the set.
Installation Water and Moisture Do not use power-line operated sets near water — for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Accessories Do not place the set on an unstable cart, stand, table or shelf. The set may fall, causing serious injury to a child or an adult and serious damage to the set. Use only a cart or stand recommended by Sony for the specific model of TV.
Lightning Safety Check For added protection for this television receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the receiver due to lightning and power-line surges.
6 Model name1[KP-46WT510] Model name2[KP-51WS510] Model name3[KP-57WS510] Model name4[KP-65WS510] [4-094-605-12]
8 Model name1[KP-46WT510] Model name2[KP-51WS510] Model name3[KP-57WS510] Model name4[KP-65WS510] [4-094-605-12]
Contents Introducing the Sony Projection TV Presenting the Sony Projection TV..........................8 Using this manual ....................................................9 Installing and Connecting the Projection TV Contents .................................................................10 Inserting Batteries into the Remote Control ..........10 Carrying Your Projection TV ................................11 Installing the Projection TV...................................11 Connector Types ...........
Introducing the Sony Projection TV Presenting the Sony Projection TV Thank you for purchasing the Sony Projection TV. This manual is for models KP-46WT510, KP-51WS510, KP-57WS510, and KP-65WS510. KP-51WS510 is used for illustration purposes, unless indicated otherwise. Features Some of the features that you will enjoy with your new projection TV include: ❑ Hi Scan 1080™: Enables you to receive the 1080i, 720p, 480p and 480i digital TV formats.
Introducing the Sony Projection TV Wide Screen Mode: Allows you to watch 4:3 normal broadcasts in wide screen mode (16:9 aspect ratio). ❑ Auto Wide: Allows you to select the wide screen mode automatically. ❑ Flash Focus™: Allows you to adjust convergence automatically. ❑ Manual Convergence: Allows you to manually adjust the convergence of specific areas of the screen.
Installing and Connecting the Projection TV Contents The box contains your new projection TV, a remote control and two AA batteries. No peripheral cables are included. If you intend to add additional equipment to your projection TV, please check the hookup instructions for your desired setup before you begin. You may need to purchase cables and/ or splitters to complete the hookup properly.
Installing and Connecting the Projection TV Carrying Your Projection TV Carrying the projection TV requires four (4) or more people. Handle (KP-65WS510 only) Installing the Projection TV 65" min . 2.4 57" min m( app rox .8 ft.) m( app rox 51" min. .7f t.) 1.8 m( app rox 46" min. .6f 1.6 t.) m( app rox .5f t.) . 2.1 Recommended viewing area (Vertical) 65"m in. 2.1 m in. 2.4 m in. (ap 1.8 pr (ap in. ox m .8 pr 1.6 (ap ox ft.) m pr . 7 (ap ox f t .6 .) pr ox ft.) .5 ft.
Installing and Connecting the Projection TV Connector Types You may find it necessary to use some of the following connector types during set up. Coaxial cable Standard TV cable and antenna cable Plug Type Push into connection. Screw-on Type Screw into connection. S Video cable High quality video cable for enhanced picture quality Align guides and push into connection. Audio/Video cable Push into connection.
Installing and Connecting the Projection TV Projection TV Controls and Connectors The front panel menu controls allow access to the on-screen menus without the use of a remote control. Pressing MENU brings up the on-screen menus. The arrow buttons move the on-screen cursor in the menus and by pressing the Select button ( ) selects the menu item.
Installing and Connecting the Projection TV Projection TV Rear and Front Panel Connectors Rear of projection TV 0 Front of projection TV 14 Model name1[KP-46WT510] Model name2[KP-51WS510] Model name3[KP-57WS510] Model name4[KP-65WS510] [4-094-605-12]
Installing and Connecting the Projection TV Connection Description Can accommodate a copy-protected digital connection (HDCP*) to other devices (such as digital set-top boxes) that have compatible interfaces. The DVI-HDTV input terminal is compliant with the EIA-861 standard, and is not intended for use with personal computers. See the instruction manual that came with your equipment for details about connecting and using it with the TV.
Installing and Connecting the Projection TV Basic Connections (Connecting Cable TV or Antenna) Connecting Directly to Cable or an Antenna The connection you choose depends on the cable found in your home. Newer homes are equipped with standard coaxial cable (see A); older homes probably have 300-ohm twin lead cable (see B); other homes may contain both (see C).
Installing and Connecting the Projection TV Cable Box Connections Cable Box and Cable This is the preferred basic cable TV hookup to use if: Your cable TV company scrambles some channels, but not all of them (pay channels vs. regular cable channels) and you need to use a cable box, and ❑ You want to enjoy the Twin View feature. With this setup you can: ❑ Use the projection TV remote control to change channels using your cable box when the signal is scrambled.
Installing and Connecting the Projection TV Cable Box Only Use this hookup if: z If you have a digital cable box, you cannot use this connection because the TO CONVERTER jack is not compatible with digital cable boxes. ❑ You subscribe to a cable TV system that uses scrambled or encoded signals requiring a cable box to view all channels, and ❑ You do not intend to hook up any other audio or video equipment to your projection TV.
Installing and Connecting the Projection TV Connecting a VCR and Cable Use this hookup if: ❑ You have cable TV that does not require a cable box. 1 2 3 Connect the cable TV cable to the VCR’s IN jack. Using a coaxial cable, connect the VCR’s OUT jack to the projection TV’s VHF/UHF jack. Using AUDIO and S VIDEO cables, connect the VCR’s Audio and S Video OUT jacks to the projection TV’s AUDIO and S VIDEO IN jacks.
Installing and Connecting the Projection TV Connecting a VCR and Cable Box Use this hookup if: ❑ Your cable TV company scrambles some channels, but not all of them (pay channels vs. regular cable channels) and you need to use a cable box, and ❑ You want to enjoy the Twin View feature. With this setup you can: ❑ Use the projection TV remote control to change channels on your cable box when the signal is scrambled.
Installing and Connecting the Projection TV VCR Coaxial cable VIDEO (yellow) AUDIO-L (white) AUDIO-R (red) S VIDEO VMC-810S/820S (not supplied) Cable box Coaxial cable Rear of projection TV ✍ If your VCR is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of the S VIDEO cable. ✍ You will not be able to change channels on the VCR. Set your projection TV and VCR to channel 3 or 4, depending on your cable box.
Installing and Connecting the Projection TV Connecting Two VCRs for Tape Editing If you connect two VCRs, you can record from one VCR to the other while using your projection TV to monitor what is being recorded. Disconnect all power sources before making any connections. 1 2 Using AUDIO and VIDEO cables, connect the playback VCR’s AUDIO and VIDEO OUT jacks to the recording VCR’s Audio and Video IN jacks.
Installing and Connecting the Projection TV Connecting a Satellite Receiver Disconnect all power sources before making any connections. 2 3 Connect the satellite antenna cable to the satellite receiver’s SATELLITE IN jack. Using AUDIO and S VIDEO cables, connect the satellite receiver’s AUDIO and S VIDEO OUT jacks to the projection TV’s AUDIO and S VIDEO IN jacks. Connect a coaxial cable from your cable or antenna to the projection TV’s VHF/UHF jack.
Installing and Connecting the Projection TV Connecting a Satellite Receiver with a VCR Disconnect all power sources before making any connections. 1 2 3 4 5 Connect the satellite antenna cable to the satellite receiver’s SATELLITE IN jack. Connect the CATV cable to the VCR’s VHF/UHF IN jack. Using a coaxial cable, connect the VCR’s OUT jack to the projection TV’s VHF/UHF jack.
Installing and Connecting the Projection TV Connecting an Audio Receiver Disconnect all power sources before making any connections. Rear of projection TV AUDIO-R (red) AUDIO-L (white) RK-74A (not supplied) Line input 25 Model name1[KP-46WT510] Model name2[KP-51WS510] Model name3[KP-57WS510] Model name4[KP-65WS510] [4-094-605-12] Installing and Connecting the Projection TV Using audio cables, connect the projection TV’s AUDIO OUT (VAR/FIX) jacks to the audio receiver’s audio LINE IN jacks.
Installing and Connecting the Projection TV Connecting a DVD Player with Component Video Connectors This is the preferred hookup to use if: ❑ Your DVD player has component (Y, B-Y, R-Y) jacks. Disconnect all power sources before making any connections. 1 Using three separate component video cables, connect the DVD player’s Y, B-Y and R-Y jacks to the Y, PB and PR jacks on the projection TV. Use the VIDEO IN 5 or 6 connections.
Installing and Connecting the Projection TV Connecting a DVD Player with A/V Connectors Use this hookup if: ❑ Your DVD player does not have component (Y, PB, PR) jacks. picture quality use the connection described on page 26. Disconnect all power sources before making any connections. 1 2 Using audio cables, connect the DVD player’s Audio OUT jacks to the projection TV’s AUDIO IN jacks. Using an S VIDEO cable, connect the DVD player’s S VIDEO jack to the projection TV’s S VIDEO jack.
Installing and Connecting the Projection TV Connecting a Digital TV Receiver Disconnect all power sources before making any connections. z Be sure to read the Set-top box manual. 1 Using three separate component video cables, connect the Digital TV Set-top box’s Y, PB and PR jacks to the projection TV. ✍ The Y, PB and PR jacks do not provide audio, so audio cables must z Some Digital TV Receivers are equipped with a DVI connection.
Installing and Connecting the Projection TV Connecting a Camcorder Using AUDIO and S VIDEO cables, connect the camcorder’s Audio and S VIDEO OUT jacks to the projection TV’s AUDIO and S VIDEO IN jacks. ✍ If you have a mono camcorder, connect its left audio output to the projection TV’s AUDIO L (MONO) jack. ✍ If your camcorder is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of the S VIDEO cable.
Installing and Connecting the Projection TV Connecting an AV Receiver For greater control of all audio and video equipment, connect an AV receiver. ✍ Change “Video Label” for the VIDEO 1 input to “Receiver” (see page 61). z You can connect an AV receiver using both composite video and S VIDEO. If both are connected, then the TV will detect and display an S VIDEO signal. To take advantage of this feature, connect your receiver with Video 1. Disconnect all power sources before making any connections.
Installing and Connecting the Projection TV Using the CONTROL S Feature Rear of projection TV 31 Model name1[KP-46WT510] Model name2[KP-51WS510] Model name3[KP-57WS510] Model name4[KP-65WS510] [4-094-605-12] Installing and Connecting the Projection TV CONTROL S allows you to control your projection TV system and other Sony equipment with one remote control.
Installing and Connecting the Projection TV Setting Up the Projection TV Automatically After you finish connecting your projection TV, you can run Auto Setup to set up your channels. The Auto Setup screen appears when you turn your projection TV on for the first time after installing it. If you do not want to set up the channels at this time, you can do it later by using the Auto Program feature in the Channel menu (see page 56).
Installing and Connecting the Projection TV Adjusting the Convergence Automatically – FLASH FOCUS™ – The projection tube image appears on the screen in three colors (red, green and blue). If they do not converge, the color is poor and the picture blurs. The FLASH FOCUS feature allows you to adjust the convergence automatically. ✍ It is recommended to perform FLASH FOCUS about 30 minutes after the projection TV is first turned on. Projection TV front panel 1 2 Receive a TV or cable TV program.
Installing and Connecting the Projection TV Adjusting the Convergence Manually The Manual Convergence feature gives you more control over the TV's picture than the Flash Focus feature, allowing you to fine-tune the color alignment of each section of the TV screen. ✍ Before using Manual Convergence, you must first perform Flash Focus (as described on page 33). ✍ Use the joystick of your remote control to perform the steps below. z For details on using the Setup Menu, see page 60.
Installing and Connecting the Projection TV Notes on Adjusting the Convergence Manually For best results, stand about 3 to 5 feet back from the picture when adjusting the convergence. Begin with the crosses in the center area of the screen and, once those are adjusted, move to the crosses on the edges of the screen. ❑ You can make separate adjustments to each wide mode: Full/Normal, Zoom, Wide Zoom, and 1080i high-definition input.
Using the Features Using the Remote Control The following table describes the buttons on the remote control that are for more advanced functions. Button Descriptions Outside Panel Button Description 1 MUTING Press to mute the sound. Press again or press VOL + to restore the sound. 2 SLEEP Press repeatedly until the projection TV displays the time in minutes (15, 30, 45, 60, or 90) that you want the projection TV to remain on before shutting off automatically.
Using the Features Button Description Turn on and off the projection TV and other audio/video equipment you have programmed into the remote control. For instructions, see “Programming the Remote Control” on page 70. qf FUNCTION buttons Select the equipment (TV, SAT/CABLE) that you want to operate. The indicator lights up momentarily when pushed to show which device the remote control is operating.
Using the Features Inside Panel Button Description 1 SYSTEM OFF Press to turn off the projection TV and all equipment connected with S-Link. 2N Play 3m Rewind 4 REC Record 5x Stop 6 DVD MENU Displays the DVD menu. 7 MTS/SAP Press to scroll through the Multi-channel TV Sound (MTS) options: Stereo, Auto SAP, and Mono. 8 CODE SET Used for programming the remote control to operate nonSony video equipment. For details, see “Programming the Remote Control” on page 70.
Using the Features Watching the TV Many TV features can be accessed directly through the remote control. The following will explain the function of some of the buttons found on your remote control. 1 TV (FUNCTION) Activates the remote control for use with the projection TV. 2 ANT— (AUX input) Press to change between the VHF/UHF input and the AUX input. 3 TV (POWER) Turns the projection TV on and off. If a video input indication (e.g.
Using the Features qa DISPLAY Press to display the channel number, current time and channel label (if set). To turn the display off, press DISPLAY again. qs TV/VIDEO Press repeatedly to scroll through available video inputs: TV, VIDEO 1, VIDEO 2, VIDEO 3, VIDEO 4, VIDEO 5 VIDEO 6, and VIDEO 7. If you select Skip as a Video Label in the Setup menu, your projection TV will skip the video input you selected (see “Video Label” on page 61).
Using the Features Watching the Digital TV When you have connected the DTV receiver, you can enjoy digital TV programs. This projection TV is capable of receiving 1080i, 720p, 480p and 480i digital TV formats (note that 720p is displayed as 480p). To view a digital TV program Connect the DTV receiver to VIDEO 5, 6 or 7 IN on the projection TV. (for details, see page 28) 2 3 Press TV/VIDEO to select VIDEO 5, 6 or 7. 4 Adjust the volume of the projection TV as necessary.
Using the Features Using Favorite Channels The Favorite Channel feature lets you select programs from a list of favorite channels that you preset. To display a list of your favorite channels: ✍ Your Favorite Channel options can be set automatically or manually. The factory setting for Favorite Channel is Auto. When Favorite Channel is set to Auto, the last eight channels selected with 0-9 buttons will be set as Favorite Channel options.
Using the Features Using Twin View™ Twin View enables you to watch two programs at the same time. You can also change the size of both the left and right pictures. Activating Twin Pictures To display twin pictures Make sure your projection TV is tuned to a working channel. 2 Press . To cancel twin pictures again (or press ❑ Press Activating the Picture Using the Features 1 ). Although two pictures appear on the screen at the same time, only one picture is active.
Using the Features ✍ Factors Affecting Twin View: - If you use a cable box to view all channels, the same channel appears in both windows because the cable box unscrambles only one channel at a time. - If you use a cable box, you can view the cable box output in one window and view a different source (such as a VCR or DVD player) in the second window by using the TV/VIDEO button. - Sources connected to the AUX, VIDEO 5, VIDEO 6, and VIDEO 7 inputs display in the left window, but not the right.
Using the Features Changing the Picture Size The zoom feature lets you change the size of the left and right pictures. To enlarge the left picture (reduce the right) v To enlarge the right picture (reduce the left) Move the joystick left to activate the left picture (if not already activated). 1 Move the joystick right to activate the right picture (if not already activated). 2 Move the joystick up to enlarge the picture and move the joystick down to reduce the picture.
Using the Features Using the Freeze Function The FREEZE button allows you to temporarily capture a program’s picture. You can use this feature to write down information such as phone numbers, recipes, etc. To use the Freeze function 1 When the program information you want to capture is displayed, press FREEZE. 2 The projection TV switches to Twin View mode and displays the “frozen” picture on the right, while the current program continues on the left.
Using the Features Using Scrolling Channel Index Scrolling Channel Index allows you to view and select from all receivable channels scrolling on the screen without leaving the current channel. ✍ Scrolling Channel Index will not function when Parental Lock is activated. 1 Press . The current channel will be reduced in size and displayed on the left in normal motion picture format. The first channel is briefly displayed on the bottom-right side of the screen, then frozen.
Using the Features 4 Press . The selected channel will be enlarged for normal viewing. 8 To cancel Scrolling Channel Index Press again to resume normal viewing. ✍ Sound will only be heard from the center picture. ✍ If one of the pictures received through Scrolling Channel Index is snowy, the entire screen may become unstable. In this case, skip the snowy channel.
Using the Features Using Wide Mode Wide Screen mode lets you watch 4:3 normal broadcasts in several Wide Screen modes (16:9 aspect ratio). Example ✍ When viewing high-definition programs broadcast in 720p/1080i, it is not possible to change between Wide Screen modes. ❑ Press WIDE MODE repeatedly to toggle through the following Wide Mode settings.
Using the Menus Overview Opening and choosing a menu: 1 2 3 4 Press MENU to display the menu screen. Move the joystick to the desired menu icon and press to select it. Use the joystick to scroll through the features. See the specific menu page for instructions on moving through the menu. The menu gives you access to the following features: Menu Icon Description Page Allows you to make adjustments to your picture settings.
Using the Menus Using the Video Menu To select the Video Menu 1 2 Press MENU. 3 Use the joystick to scroll through the features. 4 Press to select a feature. That feature’s adjustment appears. 5 6 7 Use the joystick to make the desired adjustments. Move the joystick to the Video icon and press . Using the Menus Press to select/set. Press MENU to exit the menu screen.
Using the Menus Option Description DRC Mode Digital Reality Creation Creates a high-resolution picture with 4x density, for high quality sources (i.e., DVD player, Satellite receiver). Interlaced Recommended for moving pictures. Progressive Recommended for still images and text. CineMotion Recommended for 24 frame-per-second films.
Using the Menus Using the Audio Menu To select the Audio Menu 1 2 Press MENU. Move the joystick to the Audio icon and press . Use the joystick to scroll through the options. 4 Press to select an option. That option’s settings appear. 5 6 7 Use the joystick to scroll through the settings. Press Using the Menus 3 to select the desired setting. Press MENU to exit the menu screen.
Using the Menus Option Speaker Audio Out Easy control of volume adjustments Description On Select to turn on the projection TV speakers. Off Select to turn off the projection TV speakers and listen to the projection TV's sound only through your external audio system speakers. Variable The projection TV’s speakers are turned off, but the volume output from your audio system can still be controlled by the projection TV’s remote control.
Using the Menus Using the Channel Menu To select the Channel Menu Press MENU. 3 Use the joystick to scroll through the features. 4 Press to select a feature. That feature’s options appear. 5 6 7 Use the joystick to scroll through the options. Move the joystick to the Channel icon and press . Press Using the Menus Selecting Channel Options 1 2 to select the desired option. Press MENU to exit the menu screen.
Using the Menus Option Description Channel Fix 2-6 Useful when you have a cable box or satellite receiver connected AUX 2-6 Video 1 “Fix” your projection TV’s channel setting to 3 or 4 and use the cable box, VCR or satellite receiver to change channels. Select one of these settings if you have connected the device to the VHF/UHF jack. Same as 2-6, except you select one of these settings if you have connected the device to the AUX jack.
Using the Menus Using the Wide Menu To select the Wide menu 1 2 Press MENU. 3 Move the joystick to scroll through the features. 4 Press to select a feature. That feature’s options appear. 5 6 7 Use the joystick to scroll through the options. Use the joystick to move to the Wide icon and press . Using the Menus Press to select the desired option. Press MENU to exit the menu screen.
Using the Menus z If 4:3 Default is set to anything but Off, the Wide Mode setting changes only for the current channel. When you change channels (or inputs), Wide Mode is automatically replaced with the 4:3 Default setting. To retain the current Wide Mode setting as channels and inputs are changed, set 4:3 Default to Off. Option Description Vertical Center Allows you to move the position of the picture up and down in the window. (Available only in Wide Zoom and Zoom modes.
Using the Menus Using the Timer Menu To select the Timer menu 1 2 Press MENU. Move the joystick to the Timer icon and press . To set the Current Time Use the joystick to select “Current Time”, then press . 2 If it is currently Daylight Saving Time, be sure to set the mode to “On” first. 3 4 Use the joystick to enter the correct time, then press . Press MENU to exit the menu screen.
Using the Menus Using the Setup Menu To select the Setup Menu Selecting Setup Options 1 2 Press MENU. 3 Use the joystick to scroll through the features. 4 Press to select a feature. That feature’s options appear. 5 6 7 Use the joystick to scroll through the options. Move the joystick to the Setup icon and press . Press to select the desired option. Press MENU to exit the menu screen.
Using the Menus Option Description Video Label Allows you to label the audio/video components you connected to the projection TV so you can identify them when using TV/ VIDEO. When in the Setup menu’s Video Label feature, use the joystick to highlight an input to label, then press to select it. Use the joystick to scroll through the labels. Press to select the component you connected to each of the input jacks on the back of your projection TV.
Using the Menus Using the Parent Menu The Parent menu allows you to set up the TV to block programs according to their content and rating levels. These ratings are assigned by a federal rating board. Not all programs are rated. Using the Parental Lock blocks programs with a specific rating, but it does not block an entire channel. ✍ Scrolling Channel Index will not function when Parental Lock is activated. To select the rating First, set a password, then select the country you reside in (U.S.A.
Using the Menus 6 Make sure that “Country” is selected, and press 7 Move the joystick up or down to select U.S.A. or Canada according to the country you reside in, and press . 8 Move the joystick down to select “Parental Lock”, and press 9 Move the joystick up or down to select a desired rating, and press . Using the Menus . . If you select Child, Youth, Young Adult or Custom, the Parental Control is activated automatically.
Using the Menus The Parent menu includes the following options. z If you are not familiar with the Parental Guideline rating system, you should select Child, Youth, or Young Adult to help simplify the rating selection. To set more restrictive ratings, select Custom. z For descriptions of Child, Youth, and Young Adult ratings, see pages 68 and 69. Option Description Parental Lock Off Turn ratings on/ off and select a Child rating system Change Password Parental lock is off.
Using the Menus Using Custom Rating Options If you want to select the ratings to be blocked from Custom, follow the procedure below. 1 Perform the steps 1 to 8 in “To select the rating” on page 62 to display the Parental Lock options. 2 Move the joystick up or down to select “Custom,” and press 3 Make sure that “Movie Ratings” is selected, and press 4 Move the joystick up or down to select the rating to be blocked, and press . . Using the Menus .
Using the Menus 5 Move the joystick left, then down, to select “TV Rating” or “Program,” and press . 6 The “TV Rating” setting menu appears. 7 Move the joystick up or down to select the rating to be blocked, and press . The indicator automatically appears beside the selected rating and all “higher” ratings, indicating that the programs that match the ratings will be blocked. To unblock a rating, select it by moving the joystick up or down, then press .
Using the Menus 8 Move the joystick left or right to select the extender to be viewed, and press . If you press again, is displayed to show that the programs that match the extender will be blocked again. 9 Repeat step 8 for other extenders. All programs that match the ratings you select and higher, except for the extenders that were canceled, will be blocked. 10 Press MENU to exit the menu screen.
Using the Menus US custom rating options If you selected U.S.A. as the country of residence on page 62, the Custom Rating Menu includes the following options. (If you selected Canada, see page 69.) Option Description Movie Rating G All children and General Audience. PG Parental Guidance suggested. PG-13 Parental Guidance for children under 13. R Restricted viewing, parental guidance is suggested for children under 17. NC-17 and X No one 17 and under allowed.
Using the Menus Canadian custom rating options If you selected Canada as the country of residence on page 62, the Custom Rating Menu includes the following options. (If you selected U.S.A., see page 68.) Option English Rating USA Rating C All children. C8+ Children 8 years and older. G General programming. PG Parental Guidance. 14+ Viewers 14 and older. 18+ Adult programming. G General programming. 8 ans+ Not recommended for young children. 13 ans+ Not recommended for ages under 13.
Other Information Programming the Remote Control The remote control is preset to operate Sony brand video equipment. Sony Equipment Switch Position on Remote Control Programmable Code Number Beta, ED Beta VCRs AV1 303 8 mm VCR AV2 302 VHS VCR AV3 301 DVD Player DVD 751 If you have video equipment other than Sony brand that you want to control with the projection TV’s remote control, use the following procedures to program the remote control.
Other Information To program video equipment 1 2 3 Open the panel of the remote control. Move the slide switch to the desired component type. Press CODE SET inside the panel. ✍ You must perform step 4 within 10 seconds of step 3, or you must start again from step 3. Close the panel and enter the three-digit manufacturer’s code number using the 0-9 buttons. 5 6 Press ENTER.
Other Information Manufacturer’s Codes VCRs Manufacturer Code Sony 301 Admiral (M.
Other Information Operating Other Components with Your Projection TV Remote Control Operating a VCR Open the panel and move the slide switch to the AV input you coded for this device. To Do This ...
Other Information Operating a Cable Box Operating a Satellite Receiver To Do This ... Press Turn on/off SAT/CABLE (POWER) Select Cable Box SAT/CABLE (FUNCTION) Select a channel 0-9 buttons, ENTER Change channels CH +/– Back to previous channel JUMP To Do This ...
Other Information Troubleshooting If, after reading these operating instructions, you have additional questions related to the use of your Sony television, please call our Customer Information Services Center at 1-800-222-SONY (7669) (U.S. residents only) or (416) 499-SONY (7669) (Canadian residents only). Problem Possible Remedies No picture (screen not lit), no sound ❏ ❏ ❏ ❏ ❏ ❏ Remote control does not operate ❏ ❏ ❏ ❏ ❏ Batteries could be weak. Replace the batteries.
Other Information Problem Possible Remedies Projection TV is fixed to one channel ❏ ❏ Use Auto Program in the Channel menu to add receivable channels that are not presently in TV memory (see page 56). Check your Channel Fix settings (see page 56). Double images or ghosts ❏ Use a highly directional outdoor antenna or a cable (when the problem is caused by reflections from nearby mountains or tall buildings).
Other Information Problem Possible Remedies You get the same program in the ❏ window picture as in the main picture ❏ Both may be set to the same channel. Try changing channels in either the main picture or the window picture. You may be running all your channels through a cable box. The cable box will only unscramble one signal at a time, so you cannot use the Twin View feature.
Other Information Specifications Projection System Picture Tube Projection Lenses Antenna Television System Screen Size (measured diagonally) Channel Coverage VHF UHF CATV Power Requirements Number of Inputs / Outputs DVI-HDTV 3 picture tubes, 3 lenses, horizontal in-line system 7-inch high-brightness monochrome tubes (6.3 raster size), with optical coupling and liquid cooling system High performance, large diameter hybrid lens F1.
Other Information Dimensions (W × H × D) Mass 230 W Under 1 W RM-Y909 2 supplied for remote control Other Information Power Consumption In Use In Standby Supplied Accessories Remote Control AA (R6) Batteries Optional Accessories AV Cable Audio Cable Control S Cable Component Video Cable AV Receiver TV Stand 42 3/4 × 40 × 24 inches (1,086 × 1,017 × 609 mm) (KP-46WT510) 47 × 53 1/8 × 25 5/8 inches (1,194 × 1,350 × 650 mm) (KP-51WS510) 52 1/4 × 54 1/4 × 27 1/4 inches (1,326 × 1,377 × 690 mm) (KP-57WS510) 6
Index A Activating a Twin View screen 43 Adding channels to the channel list 56 Adjusting audio, Steady Sound 53 ANT button 36 Antenna, connecting 16 Audio menu 50, 53 Audio receiver, connecting 25 Audio/Video cable 12 Auto Program (channel setup) 32, 56 AV receiver, connecting to TV OUT 15, 30 B Balance, adjusting 53 Bass, adjusting 53 Batteries, inserting in remote 10 Bilingual audio 53 Brightness, adjusting 51 Contents of box 10 CONTROL S 31 Convergence, adjusting automatically 33 Convergence, adjust
Jump, using 39 L Label channels 56 video inputs 61 M MENU button 37 Menus Audio 50, 53 Channel 50, 55 Setup 50, 60 Timer 50, 59 Video 50, 51 Wide 50, 57 S S Video cable 12 SAT/CABLE function button 37 SAT/CABLE power button 37 Satellite receiver connecting 23 using with TV remote control 74 Setting up channels 32, 56 Setup menu 50, 60 Sharpness, adjusting 51 SLEEP button 36 Sleep, using 39 Specifications 78–79 Steady Sound adjusting 53 described 8 MODE P Parental control, described 8 Password, ch
