D:\Cmeng's JOB\SONY TV\SY0251_T1 (Rev-3)\4167239131_GB\010COV.
Introduction Trademark information Thank you for choosing this Sony product. Before operating the TV, please read this manual thoroughly and retain it for future reference. The illustrations used in this manual are of the KLV-32EX300 unless otherwise stated. • HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. • “BRAVIA” and are trademarks of Sony Corporation.
D:\Cmeng's JOB\SONY TV\SY0251_T1 (Rev3)\4167239131_GB\010COVTOC.fm masterpage:Left Table of Contents Start-up Guide Checking the accessories ..................................4 1: Attaching the stand.........................................4 2: Connecting an antenna/cable/VCR ................5 3: Preventing the TV from toppling over .............5 4: Bundling the cables ........................................6 5: Performing the initial set-up............................6 Watching TV .....................
D:\Cmeng's JOB\SONY TV\SY0251_T1 (Rev3)\4167239131_GB\030STU.
B KLV-22EX300 Connecting an antenna/cable and VCR 8 Antenna cable Start-up Guide • Fix the TV to the stand according to the arrow marks that guide the screw holes using the supplied screws. • This TV is very heavy, so two or more people should place the TV onto the stand. • If using an electric screwdriver, set the tightening torque at approximately 1.5 N·m (15 kgf·cm). • Ensure the AC power cord is away from screw holes during stand installation to avoid damage to the AC power cord.
4: Bundling the cables KLV-40/32EX600 “Programme Sorting”: If you want to change the order of channels, follow the steps in “Programme Sorting” (page 22). Press MENU to exit. • You can also tune channels manually (page 22). • Language options vary depending on model. 2 1 3 KLV-40/32NX500/KLV-32/26NX400 2 1 Watching TV 3 1 Press 1 on the TV to turn on the TV. 2 Press the number buttons or PROG +/– to select a TV channel.
B KLV-40/32NX500/KLV-32/26NX400 0° Detaching the stand from the TV 6° • Do not remove the stand for any reason other than to wall-mount the TV.
– Do not install the TV set as shown below. KLV-40/32EX600/ KLV-32NX500/ KLV-32NX400 Safety information Air circulation is blocked. Installation/Set-up Install and use the TV set in accordance with the instructions below in order to avoid any risk of fire, electrical shock or damage and/or injuries. KLV-55/46/40/32EX500/ KLV-46/40/32EX400/ KLV-32EX300/ KLV-40NX500 Installation • The TV set should be installed near an easily accessible AC power outlet.
Environment: Optional Equipment Places that are hot, humid, or excessively dusty; where insects may enter; where it might be exposed to mechanical vibration, near flammable objects (candles, etc). The TV set shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the TV. Situation: Do not use when your hands are wet, with the cabinet removed, or with attachments not recommended by the manufacturer.
Operating the TV Overview of the remote 1 "/1 – TV standby Press to turn the TV on or to switch to standby mode. 2 BRAVIA Sync N/x/m/M/./>: You can operate the BRAVIA Sync-compatible equipment that is connected to the TV. Some other buttons on the remote control may also operate BRAVIA Sync equipment. SYNC MENU: Press to display the BRAVIA Sync Menu and then select connected HDMI equipment from “HDMI Device Selection”.
Rear of Remote Control qf 2 +/– – Volume Adjusts volume. qg % – Mute Press to mute the sound. Press again to restore the sound. qh / – Text In Text mode: Displays Text broadcast. Each time you press /, the display changes cyclically as follows: Text t Text over the TV picture (mix mode) t No Text (exit the Text service) qj RETURN • Returns to the previous screen of any displayed menu. • When playing a photo/music/video file: Press to stop the playback (the display returns to the file or thumbnail view).
Overview of the TV buttons and indicators 1 1 – Power Press to turn the TV on or to switch to standby mode. • To disconnect the TV from the AC power completely, pull the plug from the AC power outlet. PROG 2 PROG +/–/ / • Selects the next (+) or previous (–) channel. • In TV menu: Moves through the options up ( ) or down ( ). 3 2 +/–/ / • Increases (+) or decreases (–) the volume. • In TV menu: Moves through the options right ( or left ( ).
D:\Cmeng's JOB\SONY TV\SY0251_T1 (Rev3)\4167239131_GB\060OPT.fm masterpage:Left Using Optional Equipment Connecting optional equipment You can connect a wide range of optional equipment to your TV.
Viewing pictures from the connected equipment Turn on the connected equipment, then press / to display the connected equipment list. Press F/f to select the desired input source, then press . (The highlighted item is selected if 2 seconds pass without any operation after pressing F/f.) When the input source is set to “Skip” in the “Video Labels” under the “AV Set-up” menu (page 24), that input is greyed out in the list.
Viewing Twin Picture Viewing PIP (Picture in Picture) You can view two pictures (in Component and HDMI input mode) on the screen simultaneously. Connect the optional equipment (page 13), and make sure that images from the equipment appear on the screen (page 14). You can view two pictures (in PC input mode) on the screen simultaneously. Connect a PC (page 13), and make sure that images from a PC appear on the screen (page 14). 1 Press . 1 Press . Two pictures are displayed simultaneously.
D:\Cmeng's JOB\SONY TV\SY0251_T1 (Rev3)\4167239131_GB\070MEN.fm masterpage:Left Using MENU Functions Navigating through menus The MENU button allows you to access a variety of TV settings and USB media files. MENU Photo Music Video Settings Exit 1 2 3 4 Press MENU on the TV or remote. Press F/f to select an option, then press . Follow the instructions on the screen. To exit the menu, press MENU.
• When you connect a Sony digital still camera, set the camera’s USB connection mode to Auto or Mass Storage. For more information about USB connection mode, refer to the instructions supplied with your digital camera. • Check the website below for updated information about compatible USB devices. http://www.sony-asia.com/bravia/flash.html • Use a USB storage device that is compliant with USB mass storage device class standards.
Settings adjustment • The options you can adjust vary depending on the situation. Unavailable options are greyed out or not displayed. Picture Picture Mode Sets a picture mode. The options that can be selected differ depending on the “Scene Select” settings. “Vivid”: Enhances picture contrast and sharpness. “Standard”: For standard pictures. Recommended for home entertainment. “Custom”: Allows you to store your preferred settings. “Game-Standard”: Select for standard picture suitable for games.
Advanced Settings Allows you to set “Picture” settings in more detail. These settings are not available when “Picture Mode” is set to “Vivid”. “Reset”: Resets all the advanced settings except “White Balance” to the factory settings. “Adv. Contrast Enhancer”: Automatically adjusts “Backlight” and “Picture” to the most suitable settings judging from the brightness of the screen.
“Music”: Delivers surround effects that make you feel like you are surrounded by sound as in a music hall. “Sports”: Delivers surround effects that make you feel like you are watching a live sports contest. “Game”: Delivers surround effects that enhance game sound. “Off”: Converts and reproduces multi-ch audio to 2ch audio. In the case of other audio formats, the original audio is reproduced. Dual Sound Sets the sound from the speaker for a stereo or bilingual broadcast.
Vertical Shift Adjusts the vertical position of the picture when “Wide Mode” is set to “Wide Zoom” or “Zoom”. PC Settings “Wide Mode” Selects a screen mode for displaying input from your PC, see page 11. “Reset” Resets all the “PC Settings” except “Wide Mode” to the factory settings. “Auto Adjustment” Automatically adjusts the display position, phase and pitch of the picture when the TV receives an input signal from the connected PC. z • “Auto Adjustment” may not work well with certain input signals.
Channel Set-up 1 Digit Direct When “1 Digit Direct” is set to “On”, you can select a channel using one preset number button (0-9) on the remote. • When “1 Digit Direct” is set to “On”, you cannot select channel numbers 10 and above entering next digit using the remote. Auto Tuning Tunes in all the available channels. This option allows you to retune the TV after moving house, or to search for new channels that have been launched by broadcasters.
“Audio Filter” Improves the sound of individual channels when distortion occurs in mono broadcasts in TV system “B/G”, “I” and “D/K”. • You cannot receive stereo or dual sound when “High” is selected. “Skip” Skips unused channels when you press PROG +/– to select channels. (You can still select a skipped channel using the number buttons.) “Colour System” Selects the colour system (“Auto”, “PAL”, “SECAM”, “NTSC3.58”, “NTSC4.43” or “PAL60”) according to the channel.
Timer Settings Sets the timer to turn on/off the TV. “Sleep Timer” Sets the TV to automatically switch to standby mode after a certain amount of time. z • If you turn off the TV and turn it on again, “Sleep Timer” is reset to “Off”. “On Timer” Sets the TV to automatically turn on from standby mode. “Clock Set” Allows you to adjust the clock manually. • “Clock Set” will automatically reset when you turn off the AC power.
“HDMI Device List” Displays a list of connected equipment that is compatible with Control for HDMI. Selects “Enable” to update the “HDMI Device List”. “Device Control Keys” Select button functions of the TV’s remote control to operate the connected equipment. “Normal”: For basic operations, such as navigation buttons (up, down, left or right, etc). “Tuning Keys”: For basic operations and operation of channel-related buttons, such as PROG +/– or number buttons (0-9), etc.
D:\Cmeng's JOB\SONY TV\SY0251_T1 (Rev3)\4167239131_GB\080ADD.fm masterpage:Left Additional Information Installing the accessories (Wall-Mount Bracket) To Customers: For product protection and safety reasons, Sony strongly recommends that installing of your TV be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself. To Sony Dealers and Contractors: Provide full attention to safety during the installation, periodic maintenance and examination of this product.
SU-WL500: Screen centre point SU-WL50B: a b c c b a Screen centre point Display dimensions Length for each mounting angle Angle (0°) Angle (20°) Screen centre dimension Model name D C A B F E SUWL500 SUWL50B SUWL500 SUWL50B SUWL500 SUWL50B G H SU-WL500 only KLV-55EX500 1324 795 25 78 428 481 165 166 413 752 466 KLV-46EX500 1127 676 84 137 426 478 161 162 369 640 463 KLV-46EX400 1127 674 84 137 424 478 162 162 369 640 464 KLV-40EX600 952 581 13
Screw and hook locations diagram/table Screw location - When installing the Mounting Hook on the TV. SU-WL500 SU-WL50B Hook location - When installing the TV onto the Base Bracket.
Troubleshooting Check whether the 1 (standby) indicator is flashing in red. When it is flashing The self-diagnosis function is activated. 1 Count how many times the 1 (standby) indicator flashes between each three second break. For example, the indicator flashes three times, then there is a three second break, followed by another three flashes, etc.
General The TV turns off automatically (the TV enters standby mode) • Check if the “Sleep Timer” is activated, or confirm the “Duration” setting of “On Timer” (page 24). • Check if the “Idle TV Standby” is activated (page 25). The TV turns on automatically • Check if the “On Timer” is activated (page 24). Some input sources cannot be selected • Select “Video Labels” and cancel “Skip” of the input source (page 24). The remote does not function • Replace the batteries.
Additional Information Specifications KLV-40EX600 KLV-46EX500 KLV-40EX500 KLV-55EX500 KLV-46EX400 KLV-40EX400 KLV-40NX500 Model name System Panel system TV system Colour/video system Channel coverage KLV-32EX600 KLV-32EX500 KLV-32EX400 KLV-26EX300 KLV-22EX300 KLV-32EX300 KLV-26NX400 KLV-32NX500 KLV-32NX400 LCD (Liquid Crystal Display) Panel B/G, I, D/K, M PAL, PAL60 (only video input), SECAM, NTSC4.43 (only video input), NTSC3.
Power and others Power requirements Screen size (measured diagonally) KLV-40NX500 KLV-32EX600 KLV-32EX500 KLV-32EX400 KLV-32EX300 110–240 V AC, 50/60 Hz 220–240 V AC, 50/60 Hz (South Africa and Tunisia only) inches 40 cm (Approx.) 32 101.6 80.1 80.0 Display resolution 1,366 pixels (horizontal) x 768 lines (vertical) 1,920 pixels (horizontal) x 1,080 lines (vertical) Power consumption Dimensions with stand (Approx.) (mm) (w × h × d) without stand (mm) Mass (Approx.
