4-433-082-12(1) LCD TV Operating Instructions Start-up Guide Watching TV Using Optional Equipment Using MENU Functions Network Set-up Additional Information KDL-42EX443 / 42EX440 / 32EX343 / 32EX340
NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced with the same rating of fuse approved by ASTA or BSI to BS 1362 (i.e., marked with or ) must be used. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover.
Table of Contents Start-up Guide 4 Safety Information...........................................................................................................10 Precautions......................................................................................................................11 Overview of the remote ..................................................................................................13 Overview of the TV buttons and indicators .................................................
Start-up Guide 1: Checking the accessories 2: Attaching the stand Table-Top Stand (1) ~ Screws for stand (M5 × 16) (3) • For best picture quality, do not expose the screen to direct illumination or sunlight. Remote RM-ED049 (1) Size AA batteries (2) Follow the assembling steps required to place on a TV stand. x To insert batteries into the remote 1 Refer to the supplied Table-Top Stand leaflet for proper attachment for some TV models.
• If using an electric screwdriver, set the tightening torque at approximately 1.5 N·m {15 kgf·cm}. • Be sure to securely tighten the three supplied screws, otherwise the TV may fall down. • Use an appropriate screwdriver to attach the screws tightly without damaging the screw head. • Please ensure the AC power cord is away from the stand installation location when you attach the stand. • Do not touch the inner side of the bottom of the TV stand to avoid being hurt.
Connecting an aerial/cable/VCR/DVD recorder with HDMI 4: Preventing the TV from toppling over Coaxial cable Terrestrial signal or cable HDMI cable Coaxial cable VCR/DVD recorder 1 Install a wood screw (4 mm in diameter, not supplied) in the TV stand. 2 Install a machine screw (M4, not supplied) into the screw hole of the TV. 3 Tie the wood screw and the machine screw with a strong cord (not supplied). The length of the M4 machine screw differs depending on the cord diameter.
5: Selecting the language, country/region and location 3 Press F/f to select the language displayed on the menu screens, then press . Language Select language. 4 Next Follow the on-screen instructions to select the country/region in which you will operate the TV. If the country/region which you want to use on the TV does not appear in the list, select “-” instead of a country/region. 5 Follow the on-screen instructions to set the PIN code. z • Any PIN code can be used, except 0000.
6: Auto-tuning the TV ~ • This step will appear if any analogue channel is found. 4 Set the current day and time. ~ 1 • This step will appear only if clock has not been obtained from digital broadcasting. Press F/f to select the broadcast type, then press . The message “Set-up complete” will appear on the screen. Press . The TV has now tuned in all the available channels.
Detaching the Table-Top Stand from the TV ~ • Do not remove the Table-Top Stand for any reason other than to wall-mount the TV. Place the TV with its screen facing down on a level and stable surface covered with a thick and soft cloth. Start-up Guide 1 ~ • Be careful not to hit the Table-Top Stand against the edge of the surface when placing the TV with its screen facing down. 2 Remove the screws guided by the arrow marks of the TV. Do not remove any other screws.
Safety Information Mains lead Handle the mains lead and socket as follows in order to avoid any risk of fire, electrical shock or damage and/or injuries: – – Installation/Set-up Install and use the TV set in accordance with the instructions below in order to avoid any risk of fire, electrical shock or damage and/or injuries. Installation • The TV set should be installed near an easily accessible mains socket. • Place the TV set on a stable, level surface.
Environment: • Places that are hot, humid, or excessively dusty; where insects may enter; where it might be exposed to mechanical vibration, near flammable objects (candles, etc). The TV set shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the TV. • Do not place the TV in a humid or dusty space, or in a room with oily smoke or steam (near cooking tables or humidifiers). Fire, electric shock, or warping may result.
• When adjusting the angle of the TV set, move it slowly so as to prevent the TV set from moving or slipping off from its table stand. Optional Equipment • Keep optional components or any equipment emitting electromagnetic radiation away from the TV set. Otherwise picture distortion and/or noisy sound may occur. • This equipment has been tested and found to comply with the limits set out in the EMC Directive using a connection signal cable shorter than 3 meters.
Overview of the remote 1 / – (Input select) • In TV mode: Press to display a list of inputs. 2 SYNC MENU Displays the menu of connected HDMI equipment. While viewing other input screens or TV programmes, “HDMI Device Selection” is displayed when the button is pressed. ~ • “Control for HDMI” (BRAVIA Sync) is only available with the connected Sony equipment that has the BRAVIA Sync or BRAVIA Theatre Sync logo or is compatible with Control for HDMI. 3 BRAVIA Sync .
w; – Subtitle setting Press to change the subtitle language (in digital mode and USB Video mode only). wa PROG +/–/ / • In TV mode: Selects the next (+) or previous (-) channel. • In Text mode (page 17): Selects the next ( ) or previous ( page. ws ) – Previous channel Press to return to the channel or external input that was last viewed (for more than 15 seconds). z • The number 5, N, PROG + and AUDIO buttons have tactile dots. Use the tactile dots as references when operating the TV.
Overview of the TV buttons and indicators 1 Light sensor 6 CH +/–/ Do not put anything over the sensor, doing so may affect its function. Remote control sensor • Receives IR signals from the remote. • Do not put anything over the sensor, as its function may be affected. 2 7 2 +/–/ / • In TV mode: Increases (+) or decreases (-) the volume. • In TV menu: Moves through the options right ( ) or left ( ). – Picture Off / LED Timer indicator • Lights up in green when the picture is switched off.
Watching TV Watching TV 1 Touch "/1 on the front of the TV to turn on the TV. When the TV is in standby mode (the 1 (standby) indicator on the TV front panel is red), press "/1 on the remote to turn on the TV. 2 Press DIGITAL/ANALOG to switch between digital and analogue modes. The channels available vary depending on the mode. 3 Press the number buttons or PROG +/– to select a TV channel.
x To access Text Press /. Each time you press /, the display changes cyclically as follows: Text t Text over the TV picture (mix mode) t No Text (exit the Text service) To select a page, press the number buttons or / . To reveal hidden information, press . Wide Zoom* Displays conventional 4:3 broadcasts with an imitation wide screen effect. The 4:3 picture is stretched to fill the screen. Normal Displays conventional 4:3 broadcasts (e.g. non-wide screen TV) in the correct proportions.
Using the Digital Electronic Programme Guide (EPG) * 1 2 In digital mode, press GUIDE. Perform the desired operation as shown in the following table or displayed on the screen. Digital Electronic Programme Guide (EPG) * This function may not be available in some countries/regions. To Do this Watch a programme Press F/f/G/g to select the programme or enter the desired programme number by numeric key, then press . Turn off the EPG Press GUIDE.
Using the Digital Programme List * The Favourite feature allows you to specify up to four lists of your favourite programmes. 1 In digital mode, press HOME, and select “Digital Programme List”, then press G/g to select the Favourite list. ~ • If Favourite list is already selected before, just press list. 2 Perform the desired operation as shown in the following table or displayed on the screen.
Using Optional Equipment Connecting optional equipment You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied.
Viewing pictures from connected equipment Symbol on the screen PC To see the equipment connected to D. z • It is recommended to use a PC cable with ferrites like the “Connector, D-sub 15” (ref. 1793-504-11, available in Sony Service Centre), or equivalent. Turn on the connected equipment, then perform one of the following operation. AV1 To see the equipment connected to E. AV2 To see the equipment connected to G. When connecting mono equipment, connect to the AV2 L socket.
To connect Do this USB K You can enjoy photo/music/video files stored in a Sony digital still camera or camcorder. Additional operation To Do this Return to normal TV mode Press DIGITAL/ANALOG. Photo Frame You can enjoy looking at photos, listening to music or seeing the clock and calendar, at the same time. You can enter photo frame mode using any of the following methods: 1 Press HOME, and then select “Photo Frame Mode”. 2 Press OPTIONS, when you are playing back the photo/music files.
3 Press HOME, and select “Music”. When playing back music, press OPTIONS > “Photo Frame Mode” to launch “Photo Frame” with the selected music. x To select Display mode You can change the photo frame display by selecting “Display Mode”. • Image and Clock • Full Screen Image Using Optional Equipment • Full Screen Clock x To select Clock Display mode There are five calendar display modes.
Using MENU Functions Navigating through TV Menu “MENU” allows you to enjoy various convenient features of this TV. You can easily select channels or inputs sources and change the settings for your TV. 1 Press HOME. 2 Press F/f to select an option, then press . To exit the menu, press HOME. Media category icon Description Photo Frame Mode You can select the frame image which enables you to enjoy with photo, music and clock. For details, see page 22.
Network Set-up Preparing a Network Setting up the Internet Connection When you connect this TV to the Internet, you can receive additional content/services provided by the MHEG Internet Connected Services feature. z • You will need to contract with an Internet service provider to connect to the Internet. • Available only with model supporting Ethernet connector. Internet Modem with router functions TV or Modem Internet z • For LAN connections, use a Category 5 cable (not supplied).
Additional Information Installing the Accessories (WallMount Bracket) x To Customers: For product protection and safety reasons, Sony strongly recommends that installing of your TV be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself. x To Sony Dealers and Contractors: Provide full attention to safety during the installation, periodic maintenance and examination of this product.
Sufficient expertise is required for installing this product, especially to determine the strength of the wall for withstanding the TV’s weight. Be sure to entrust the attachment of this product to the wall to Sony dealers or licensed contractors and pay adequate attention to safety during the installation. Sony is not liable for any damage or injury caused by mishandling or improper installation.
Screw and Hook locations diagram/table SU-WL500 (KDL-42EX443/42EX440) Model Name KDL-42EX443 KDL-42EX440 Screw location Hook location e, j b Hook location Screw location * * * Hook location “a” and “c” cannot be used for the models.
Specifications System Panel System LCD (Liquid Crystal Display) Panel LED Back Light TV System Depending on your country/region selection Analogue: B/G, D/K, L, I Digital: DVB-T, DVB-T2 (KDL-42EX443/32EX343 only), DVB-C Colour/Video System Analogue: PAL, PAL60 (only video input), SECAM, NTSC3.58, NTSC4.43 (only video input) Digital: MPEG-2 MP@ML/HL, H.264/MPEG-4 AVC HP@L4.0, MP@L4.0 Channel Coverage Analogue: 46.25 - 855.
Model name KDL- 42EX443/42EX440 32EX343/32EX340 Dimensions (with (w × h × d) stand) (Approx.) (without stand) 98.3 × 64.3 × 23.3 cm 75.3 × 51.0 × 21.3 cm 98.3 × 60.3 × 7.5 cm 75.3 × 47.1 × 7.1 cm Mass (Approx.) (with stand) 14.3 kg 7.8 kg (without stand) 13.4 kg 7.2 kg Supplied Accessories Refer to “1: Checking the accessories” on page 4. Optional Accessories See “Installing the Accessories (Wall-Mount Bracket)” on page 26.
Troubleshooting Check whether the 1 (standby) indicator is flashing in red. When it is flashing The self-diagnosis function is activated. Touch "/1 on the front of the TV to turn it off, disconnect the mains lead, and inform your dealer or Sony service centre. When it is not flashing 1 2 Check the items in the tables below. If the problem still persists, have your TV serviced by qualified service personnel.
HDMI equipment does not appear on “HDMI Device List” • Check that your equipment is compatible with control for HDMI. If “Store Display Mode: On” is displayed on the screen • Your TV is set to “Shop” mode. You need to set “Home” for “Location” in the “Auto Start-up” procedure again (page 7). No Cable TV services (programmes) found by “Digital Auto Tuning”. • Check your cable connection or your tuning configuration. • Attempt the “Digital Auto Tuning” by selecting the “Antanna” instead of “Cable”.
For useful information about Sony products 4-433-082-12(1) © 2012 Sony Corporation
