Owner's Record The model and serial numbers are located at the rear. Record the these numbers in the spaces provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No, Serial No. WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture, CAUTION: YO REDUCE THE RISK OF ELECTRIC BOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Precautions On safety * Operable the unit only on 120V Should any solid object or liquid fall into the unit, unplug it and have it checked by qualified personnel before operating it any further. * Unplug the unit from the wall pullet if it is not 1o be used for an extended period of time. To disconnect the cord, pull it out by grasping the plug. Never pull the cord itself, On installation * Place the unit un a level surface.
Connect the AC power cord last. Aka sure power is off. Cord plugs and jacks are color coded. Red plugs and jacks are for right channel (R} and white ones for the left channel {L). The cable connectors should be fully inserted into the jacks. A loose connection may cause hum and noise.
l CAUTION Do not put anything like another unit to obstruct the ventilation holes on the 1op of the unit. The feel surface installation is required for essential alr ventilation to prevent internal heat bully up In the unit, €& AM loop antenna (supplied) btttcrm ‘ To attach to a wall Extend a 610 15-meter insulated wire out of doors.
Receiving Broadcast Tuning in Automatically Tuning in Manually Yo change the AM fining interval The AM tuning interval is preset at tha factory 10 10 kHz o match the frequency allocation shyster of your country. To change the interval to 9 kHz, proceed as follows. 1 Press the SYSTEM POWER switch to turn on the unit. 2 Set the BAND FM/AM selector to AM. 3 Disconnect the AC plug from the AC outlet to tum off the unit.
2 semiotic the band, 3 sector automation tuning, 4 select the station. BAND FM/AM AUTO TUNING — TUNING + For a lower For a hie frequency. 2 Select the band. 4 Select the station, BAND Wigwam -~ TUNING + e For a higher frequency. More information on tuning in automatically Indicators in the display window » “TUNED" appears when a stations tuned in, * "STEREO" appears when an FM stereo program of sufficient signal strength is received.
Receiving Broadcasts Storing Station Frequencies into Memory Tuning into a Stored Station Directly Press SHIFT and the numeric button for the desired code. 1 Tune in a desired station. More information on storing stations How many stations can be stored stations can be stored in any order for sate alphabet (A, B, C). Therefore, 30 stations can be stored in total. I you cannot store a station successfully You can store a station only while "MEMORY" is displayed.
3 Allot one of the following codes: 4 Select number, First, select alphabet. SHIFT How long does a station remain stored? * Siring a new station on a used code erases the previously slumlord one.
Playing Back Tapes (on either Deck A or B) When pressing TAPE bunion on the remote commander, either TAPE 1 or TAPE AMIDE on which indicator has been lit is selected. More information an playing back tapes When listening to a tape recorded with Dolby NR* To play back the tapes from Deck B to Deck A Set the DOLBY NR switch to ON. Ba fore playing back the tape in the Deck B, press o> and it of the Deck A.
To stop playback, press & 4. 3 Select the tape type. To pause, press W, “To resume playback, press 9 again. TAPE SELECT Notes «TYPE LOGOTYPE * When both Decks A and B are In the playback mode, only playback from Deck B will be audible. » During playback or recording mode on a Deck, do not operable the other Deck.
Dubbing Tapes (from Deck Ato B) Recorded tape Blank tape SYSTEM Son 1 O More information on dubbing tapes Is it necessary to defect DOLBY NR? No. The tape in Deck B is automatically recorded with the same recording system as the original tape in Deck A, Notes * Do not sangs the setting of the DUBBING SPEED switch during tape dubbing. » {f the sound is affected by a television set during high speed dubbing, tum off the set or move it away from the unit.
2 Select the taps type. 3 Select the dubbing speed. TAPE SELECT datatype LOGOTYPE Be sure to use lapse of the same type for dubbing, since the switch settling s effective on both decks. More information on playing records (SEN-211 only) When the record has finished playing The tonearm will automatically return 10 the arm rest. To lift up the stylus during play Set the curing lever to ¥ . To stop during play Press REJECT. Press both buttons together.
Remote Commander B 5 OO0 installing Batteries 1 2 Two size-AA (RE) batteries Remote Commander (1] POWER button [2) TUNER PRESET 4+~ buttons B voL (volume) buttons (4] Function defectors (5] €0 player operation buttons CD »: Selects the CD function and starts CD playback Battery life About half a year of normal operation can be expected when using the Sony SUM-3 (NB) batteries. When the batteries are exhausted, the remote commander can no longer operate the unit.
Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 8-ohm loads, both channels driven, from 40 20,000 Hz; rated 100 watts per channel minimum RMS power, with less than 0.9% total harmonic distortion from 260 milliliters to rated output.
Troubleshooting Before going through the check fist below, first refer back to the connection and operating procedures. Should any problem persist after you have made these checks, consult your nearest Sony dealer, “Tuner Operation STEREO indicator blinks. * Adjust the antenna. Severe hum or noise. * The signal strength is too weak. Connect an external antenna. * Adjust the antenna. * Connect the ground wire, Cassette Deck Operation @ bunion does not activate. * No cassette in the cassette holder.
