Stereo System User Manual

ManualsBrandsSony ManualsStereo SystemHCD-XGR60

HCD-XGR6/XGR60

US Model

HCD-XGR6

E Model

HCD-XGR60

COMPACT Hi-Fi STEREO SYSTEM

— Continued on next page —

SPECIFICATIONS

• HCD-XGR6/XGR60 are the Amplifier,

CD player, tape deck and tuner in LBT-

XGR6/XGR60.

Ver 1.0 2002.02

9-873-567-01

2002B0200-1

Model Name Using Similar Mechanism NEW

CD CD Mechanism Type CDM37B-30BD60C

Section Base Unit Name BU-30BD60C

Optical Pick-up Name A-MAX.3

TAPE

Model Name Using Similar Mechanism NEW

Section

SERVICE MANUAL

Sony Corporation

Home Audio Company

Published by Sony Engineering Corporation

PHOTO :HCD-XGR60

AUDIO POWER SPECIFICATIONS

(LBT-XGR6 USA models only)

POWER OUTPUT AND TOTAL

HARMONIC DISTORTION:

With 6 ohm loads, both channels driven, from

120-10,000 Hz; rated 140 watts per channel

minimum RMS power, with no more than 10%

total harmonic distortion from 250 milli watts

to rated output.

Amplifier section

North American models:

LBT-XGR6

Continuous RMS power output (reference)

160 + 160 watts (6 ohms at

1 kHz, 10% THD)

Total harmonic distortion less than 0.07%

(6 ohms at 1 kHz, 70 W)

Other models:

LBT-XGR60

The following measured at AC 120/220/240V, 50 Hz

DIN power output (rated) 150 + 150 watts

(6 ohms at 1 kHz, DIN)

Continuous RMS power output (reference)

200 + 200 watts

(6 ohms at 1 kHz, 10% THD)

Inputs

DJ MIX RETURN*:

(phono jacks) sensitivity 250 mV,

impedance 47 kilohms

GUITAR:

(phone jack) sensitivity 75 mV,

impedance 470 kilohms

PHONO IN:

(phono jacks) sensitivity 3 mV,

impedance 47 kilohms

MIX MIC:

(phone jack) sensitivity 1 mV,

impedance 10 kilohms

GAME INPUT:

(phono jacks) sensitivity 250 mV,

impedance 47 kilohms

MD (VIDEO) IN:

(phono jack) sensitivity 450 mV

(250 mV), impedance

47 kilohms

Outputs

DJ MIX SEND*:

(phono jacks) sensitivity 250 mV,

impedance 1 kilohms

PHONES:

(stereo phone jack) accepts headphones of

8 ohms or more

Summary of content (74 pages)

PAGE 1
HCD-XGR6/XGR60 SERVICE MANUAL US Model HCD-XGR6 Ver 1.0 2002.02 E Model HCD-XGR60 • HCD-XGR6/XGR60 are the Amplifier, CD player, tape deck and tuner in LBTXGR6/XGR60. PHOTO :HCD-XGR60 Model Name Using Similar Mechanism NEW CD CD Mechanism Type CDM37B-30BD60C Section Base Unit Name BU-30BD60C Optical Pick-up Name A-MAX.
PAGE 2
HCD-XGR6/XGR60 MD (VIDEO) OUT: (phono jacks) FRONT SPEAKER: voltage 250 mV impedance 1 kilohms accepts impedance of 6 to 16 ohms General Power requirements North American models: Mexican model: Other models: * North American and Mexican models only CD player section System Compact disc and digital audio system Laser Semiconductor laser (λ=795 nm), Emission duration: continuous Frequency response 2 Hz – 20 kHz (±0.
PAGE 3
HCD-XGR6/XGR60 SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers).
PAGE 4
HCD-XGR6/XGR60 TABLE OF CONTENTS 1. GENERAL ·········································································· 5 6-14.SCHEMATIC DIAGRAM 2. DISASSEMBY ··································································· 7 3. TEST MODE ···································································· 15 4. MECHANICAL ADJUSTMENTS ····························· 17 5. ELECTRICAL ADJUSTMENTS ······························· 17 6. DIAGRAMS 6-1.
PAGE 5
HCD-XGR6/XGR60 SECTION 1 GENERAL This section is extracted from instruction manual. Mainunit ALPHABETICALORDER A–D E–G A EJECTZ/Z B EJECT wh (13) AMS.
PAGE 6
HCD-XGR6/XGR60 This section is extracted from instruction manual. BUTTON DESCRIPTIONS @/1 1 c/CLOCK SET qs h/H qj eh x qj eh .
PAGE 7
HCD-XGR6/XGR60 SECTION 2 DISASSEMBLY • The equipment can be removed using the following procedure.
PAGE 8
HCD-XGR6/XGR60 2-2. FRONT PANEL SECTION 4 Connector (CN903) 3 Connector (CN311) 5 Connector (CN722) 7 Screw (BVTP 3 X 8) 8 Lug 2Flat type wire (CN431) 1 Flat type wire (CN371) 9 Screw (BVTP 3 X 8) 0 Lug 6 Connector (CN806) qs Screw (BVTP 3 X 8) qf Claw qg Front panel section qa Connector (B deck) qd Four screws (BVTP 3 X 8) 2-3. TAPE MECHANISM DECK 1 Flat type wire (15 core) 2 Two screws (BVTP 2.6 X 8) 3 Two screws (BVTP 2.
PAGE 9
HCD-XGR6/XGR60 2-4. PANEL FL BOARD, TC-A BOARD, TC-B BOARD qaFour screws (BVTP 2.6 X 8) w;TC-A board qsThree screws (BVTP 2.6 X 8) 1Screw (BVTP 2.6 X 8) 3Bracket (TA) 2Lug qkPANEL FL board qhThree claws qj qdEight screws (BVTP 2.6 X 8) 6Connector (CN812) qfFour screws (BVTP 2.6 X 8) 7Connector (CN704) qlTwo claws 9Flat type wire (CN601) qgFour screws (BVTP 2.6 X 8) 0Two knobs (MIC) wsTC-B board 8Connector (CN703) 4Screw (BVTP 2.6 X 8) 5Bracket (TA) waTwo claws Front panel 2-5.
PAGE 10
HCD-XGR6/XGR60 2-6. MIC/GUITAR BOARD, HEADPHONE BOARD 1Connector (CN812) 2Two screws (BVTP 2.6 X 8) 3MIC bracket 4MIC/GUITAR board 5Two screws (BVTP 2.6 X 8) 6HEADPHONE bracket 7HEADPHONE board Front panel 2-7. FRONT INPUT BOARD Front panel FRONT INPUT board J804 1Four screws (BVTP 2.
PAGE 11
HCD-XGR6/XGR60 2-8. D-SW BOARD, CD-L BOARD, LID (CD) ASSY, CD-R BOARD 1Screw (BVTP 2.6 X8) 5Two screws (BVTP 2.6 X 8) 0Spring (CD) 2D-SW board qaLid (CD) assy qfTwo screws (BVTP 2.6 X 8) 6 9Sub panel (CD-L) assy 4Two screws (BVTP 2.6 X 8) qlSub panel (CD-R) assy qh 8CD-L board qgTwo screws (BVTP 2.6 X 8) 7Four screws (BVTP 2.6 X 8) 3Connector (CN704) qsConnector (CN703) qdKnob (CD) qkCD-Rboard qjFour screws (BVTP 2.6 X 8) 2-9.
PAGE 12
HCD-XGR6/XGR60 2-10. CD MECHANISM DECK (CDM37B-30BD60C) 6Two screws (BVTP 3 X 8) 1Flat type wire (CN401) 4Three screws (BVTP 3 X 8) 3Four screws (BVTP 3 X 8) 7 Wire holder 8 2Connector (CN411) 7 5Two screws (BVTP 3 X 8) 9remove two cables from wire holder.
PAGE 13
HCD-XGR6/XGR60 2-11. BASE UNIT-1 (BU-30BD60C) 3 base unit (BU-30BD60C) 2 boss 1 BU fitting screw 2-12. BASE UNIT-2 (BU-30BD60C) 6Base unit (BU-30BD60C) 1Two floating screws (DIA.12) 2Two screws (BVTP 2.
PAGE 14
HCD-XGR6/XGR60 2-13. BD BOARD BU-30BD60C 4Flat type wire (CN102) 5BD board 1Remove the two solders. 3Rivet 2Remove the two solders. 2-14. DISC TABLE Note: When the disc table is installed, adjust the positions of roller cam and mark B as shown in the figure, then set to the groove of disc table.
PAGE 15
SECTION 3 TEST MODE [MC Cold Reset] • The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer. Procedure: 1. Turn the power ON or set to the DEMO mode. 2. Press three buttons of c/CLOCK SET , TUNER ENTER , and \/1 simultaneously. 3. The set is reset, and displays “COLD RESET”, then becomes DEMO mode. [Change-over the AM Tuning Interval] • The AM tuning interval can be changed over 9 kHz or 10 kHz. Procedure: 1.
PAGE 16
HCD-XGR6/XGR60 2. Tape Deck Section • The sequence during the aging mode is following as below. • If an error occurred, stop display that step. 3. CD Section • The sequence during the aging mode is following as below. • If an error occurred, stop display that step.
PAGE 17
HCD-XGR6/XGR60 SECTION 4 MECHANICAL ADJUSTMENTS Precaution 1. Clean the following parts with a denatured alcohol-moistened swab: record/playback heads pinch rollers erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted.
PAGE 18
HCD-XGR6/XGR60 Record/Playback Head Azimuth Adjustment DECK A DECK B Note: Perform this adjustments for both decks Procedure: 1. Mode: Playback (FWD) test tape P-4-A100 (10 kHz, – 10 dB) Adjustment Location: Playback Head (Deck A). Record/Playback/Erase Head (Deck B). MAIN board MD (VIDEO) OUT jack (J701) L-CH, R-CH level meter set + – forward 2. Turn the adjustment screw and check output peaks.
PAGE 19
HCD-XGR6/XGR60 REC Bias Adjustment Procedure: 1. Mode: Record FUNCTION: VIDEO AF OSC REC Level Adjustment Procedure: 1. Mode: Record FUNCTION: VIDEO DECK B MAIN board MD(VIDEO) IN jack (J701) L-CH, R-CH 1) 315 Hz  50 mV (– 23.8 dB) 2) 10 kHz  AF OSC MAIN board MD (VIDEO) IN jack (J701) L-CH, R-CH 315 Hz, 50 mV (– 23.8 dB) blank tape CS-123 600 Ω blank tape CS-123 600 Ω attenuator DECK B attenuator set set 2. Mode: Playback 2.
PAGE 20
HCD-XGR6/XGR60 Note: Clear RF signal waveform means that the shape “◊” can be clearly distinguished at the center of the waveform. CD SECTION Note : 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. 2. Use LUV-P01 (4-999-032-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10M impedance. 4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks.
PAGE 21
HCD-XGR6/XGR60 SECTION 6 DIAGRAMS 6-1. CIRCUIT BOARD LOCATION TRANS board PANEL FL board Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • 2 : nonflammable resistor. • 5 : fusible resistor. • C : panel designation.
PAGE 22
HCD-XGR6/XGR60 6-2.
PAGE 23
HCD-XGR6/XGR60 –TUNER/TAPE DECK SECTION – IC341 + R-CH AMS DETECT Q341-343 HPF MUTE Q344,345 DECK-A 32 70 PB HEAD A 28 B R-CH 34 PB-OUT1 27 PB-L 26 B (Page 24) C (Page 24) 120 REC/PB SWITCH IC321 DECK-B 1 2 3 REC(L) LEVEL REC-OUT ALC1 MUTE ON/OFF 21 REC MUTE ON/OFF BIAS TRAP ALC ON/OFF R-CH 13 12 11 15 14 REC BIAS(L) T331 TC A+10 BIAS OSC Q331,332 ERASE HEAD RV351 IC301 R-CH C322,L321 RV321 DECK A/B SELECT PB/REC EQUALIZER AMP SWITCH Q321,322 NORM/HIGH R-C
PAGE 24
HCD-XGR6/XGR60 – MAIN SECTION – (Page 25) DISTORTION ON/OFF SWITCH Q880 – 883 DISTORTION E GUITAR AMP IC853 J802 GUITAR REC-L MIC OUT GUITAR AMP MIC AMP IC852 IC850 (2/2) C (Page 23) RV601 GUITAR LEVEL L J801 MIX MIC MIC AMP MD OUT RV602 MIC LEVEL (Page 23) PB-L INC1 5 INB1 4 INA1 3 IND1 6 ST-L D FUNCTION SELECT SWITCH 7 INPUT SELECT SWITCH PHONO EQ AMP IC601 R-CH R X0 12 X1 14 X2 15 X3 11 R-CH L A 10 MD IN X Q181 F OUT2 14 15 L+R + VL IN1 COMMAND R-CH 19 VOLUM
PAGE 25
HCD-XGR6/XGR60 – DISPLAY/KEY CONTROL/POWER SUPPLY SECTION – IC601 IC602 VF GRID DRIVE Q608,609 1 8 GR-16 GR-9 ALL BAND 75 16 15 14 13 12 11 DET B.P.F.
PAGE 26
HCD-XGR6/XGR60 6-3.PRINTED WIRING BOARD – BD SECTION – • See page 21 for Circuit Boards Location. 3 2 1 4 OPTICAL PICK-UP BLOCK OP ASSY(A-MAX.
PAGE 27
HCD-XGR6/XGR60 6-4. SCHEMATIC DIAGRAM – BD SECTION – • See page 44 for Waveforms. • See page 44 for IC Pin Function. • See page 50,51 for IC Block Diagrams. R196 680 R195 220k R194 33k C184 0.01µ B TP1 RFAC C194 0.1 F C133 33p C193 100 10V IC103 CH CXA2581N RF AMP FE RV101 E-F R109 1M R124 100k C165 0.1 F C145 0.1 F R104 33k R123 10k TP2 RFDC R120 15k X101 16.
PAGE 28
HCD-XGR6/XGR60 6-5.PRINTED WIRING BOARD – MOTOR LED SECTION – • See page 21 for Circuit Boards Location. 6-6.SCHEMATIC DIAGRAM – MOTOR LED SECTION – • See page 56 for IC Block Diagrams. LED BOARD SENSOR BOARD 4.8 TABLE MOTOR DRIVER 4.8 TRAY MOTOR BOARD B B MAIN BOARD (Page 33) MAIN BOARD(2/3) (Page 31) DISC TABLE SENSOR 4.8 LED DRIVE 28 28 4.
PAGE 29
HCD-XGR6/XGR60 6-7.SCHEMATIC DIAGRAM – MIC/GUITAR SECTION – 6-8.PRINTED WIRING BOARD – MIC/GUITAR SECTION – • See page 21 for Circuit Boards Location. 3 2 1 4 MIC/GUITAR BOARD R876 1k IC853 GUITAR AMP Q880-883 DISTORTION ON/OFF SWITCH R879 1k R872 2.2k R882 47k R880 10k Q883 DTA124ESA C881 47p 2 5 R886 390k IC852(2/2) NJM4558L 6 1 R869 68k 2 C813 0.022 8 Q882 DTC124ESA R885 10k 4 3 C815 47p R891 1M R883 47k Q881 DTC124ESA C802 R867 2.2k 2 47k R853 1k R873 2.
PAGE 30
HCD-XGR6/XGR60 6-9.SCHEMATIC DIAGRAM – MAIN (1/3) SECTION – XGR6, DJ MIX XGR60:MX SEND XGR60 XGR6 IC601 C607,657 0.033 MF 0.1 MF PHONO EQ AMP C604,654 2.2/50V 4.7/50V R604,654 1K 820 IC601(1/2) NJM4558M C655 0.0047 PET C656 0.
PAGE 31
HCD-XGR6/XGR60 6-10.SCHEMATIC DIAGRAM – MAIN(2/3) SECTION – • See page 44 for Waveforms. • See page 46 for IC Pin Function. MC2 MIC-SIG MIC SPE-SIG VF1 LED 3.9V CD-L BPF+10V CD-R MC1 D 3.9V ST-R VF2 VFDP 75 73 74 25 IN(ST-DOUT) R401 C403 100 2.2 Q401 50V Q401,402 2SC3623A MUTE R405 10k R402 3.3k C414 0.1 FB562 CN431 19P FFC-S R431 100k MIC-SIG SPEANA 23 C406 100p R583 100 R584 100 85 R585 100 86 R586 100 87 R587 100 88 R588 100 89 R589 100 90 R590 100 R596 4.
PAGE 32
HCD-XGR6/XGR60 6-11. SCHEMATIC DIAGRAM – MAIN (3/3) SECTION – • See page 44 for Waveforms. • See page 51 for IC Block Diagrams. IC341 HPF CD D+5V SW R318 10k IC341(1/2) NJM4558M Q344,345 MUTE R341 1k Q345 DTC124ESA IC341(2/2) C343 0.022 PET 8 5 7 R343 R319 100k C349 R320 2.2k C341 470 10V R342 1k 2 C344 0.022 PET 47k R338 22k 3 TC+10V Q341-343 AMS DETECT R349 4.7k Q341 2SC2603 Q342 DTC124ESA C348 22 50V R340 10k EVER+3.
PAGE 33
HCD-XGR6/XGR60 6-12.PRINTED WIRING BOARD – MAIN SECTION – • See page 21 for Circuit Boards Location.
PAGE 34
HCD-XGR6/XGR60 6-13.PRINTED WIRING BOARD – CD-L, CD-R, HEADPHONE, FRONT INPUT, D-SW SECTION – • See page 21 for Circuit Boards Location.
PAGE 35
HCD-XGR6/XGR60 R777 10k R776 6.8k R775 4.7k S748 S747 S746 R774 3.3k R773 2.2k R772 1.5k S744 S743 D-SW GND R778 15k KEY0 6-14. SCHEMATIC DIAGRAM – CD-L, CD-R, HEADPHONE, FRONT INPUT, D-SW SECTION – CN704 3P R771 1.5k S740 S749 EDIT REPEAT PLAY DISC S745 DISC4 DISC5 DISC2 DISC3 S741 S742 C741 10000p (DOOR SW) DISC1 SKIP MODE R784 6.8k CN703 7P R782 3.3k R783 4.
PAGE 36
HCD-XGR6/XGR60 6-15.PRINTED WIRING BOARD – PANEL VR SECTION – • See page 21 for Circuit Boards Location.
PAGE 37
HCD-XGR6/XGR60 LED P1 LED P2 P2 CN701 21P P1 LED P4 LED P3 P3 LED P5 P4 P5 P6 LED P6 LED3.9V LED3.9V +3.9V VL +3.9V VH GND GND KEY 3 KEY 5 VOL A CLK VOL B DATA DATA CLK LED P7 LED P8 STB STB P7 LED P9 P8 P10 P9 LED P10 6-16. SCHEMATIC DIAGRAM – PANEL VR SECTION – R705 1k R725 6.8k R726 10k R723 3.3k R724 4.7k R722 2.2k R721 1.5k R719 1k R720 1.
PAGE 38
HCD-XGR6/XGR60 6-17.PRINTED WIRING BOARD – PANEL FL, TC-A, TC-B SECTION – • See page 21 for Circuit Boards Location.
PAGE 39
HCD-XGR6/XGR60 6-18.SCHEMATIC DIAGRAM – PANEL FL, TC-A, TC-B SECTION – • See page 44 for Waveforms. 44 43 41 40 39 36 38 37 34 35 32 33 30 31 28 29 26 27 24 25 19 20 18 16 14 13 12 10 7 9 4 6 5 3 21 22 FL TUBE FL601 2 • See page 48 for IC Pin Function. • See page 52 for IC Block Diagrams. C628 1 50V C627 1 50V Q609 DTC114TLTL2 R665 100k Q608 DTC114TLTL2 R666 100k Q606-609 C625 10 50V 73 74 75 70 R655 JW R654 6.
PAGE 40
HCD-XGR6/XGR60 6-19.PRINTED WIRING BOARD – PA SECTION – • See page 21 for Circuit Boards Location.
PAGE 41
HCD-XGR6/XGR60 6-20.SCHEMATIC DIAGRAM – PA SECTION – XGR60 XGR6 TM401 IC801 IC801 D405 1SS133T STK412-040 STK442-130 FRONT SPEAKER POWER AMP POWER AMP D406 1SS133T RY401 24V Q401 DTA1124ESA JW821 + L R407 47k R406 47k – + 35.4 JW820 35.2 R460 10k 34.8 *R401 R429 47k R818 220 0 -12.4 560 XGR60 1.8k XGR6 D402 1SS133T 0 R868 220 0 3.1 -12.4 70 35.4 21.5 -35.8 -70.5 -21.8 0 0 0 0 0 0 -68.8 0 69.1 0 0 -67.5 35.4 0 0 -70.5 0 0 0 -68.8 0 69.
PAGE 42
HCD-XGR6/XGR60 6-21.SCHEMATIC DIAGRAM – TRANS, SUB TRANS SECTION (XGR6, XGR60: MX MODEL) – • See page 21 for Circuit Boards Location. 3 2 1 4 6-22.SCHEMATIC DIAGRAM – TRANS, SUB TRANS SECTION (XGR6, XGR60: MX MODEL) – 5 1 JW960 JW972 N JW974 JW976 JW978 AC-H PA BOARD (Page 40) CN951 JW977 3 A T951 *1 F963,964 P-GND POWER 6.3A 125V XGR6 6.3AL 250V XGR60:MX TRANSFORMER AC-H XGR60:MX – AC12V AC7V D832 D5SBA20 JW975 JW986 JW985 PRI-GND AC7V C834 0.
PAGE 43
HCD-XGR6/XGR60 6-23.PRINTED WIRING BOARD – TRANS, SUB TRANS SECTION (XGR60:E, E51, AR MODEL) – • See page 21 for Circuit Boards Location. 3 2 1 4 6-24.SCHEMATIC DIAGRAM – TRANS, SUB TRANS SECTION (XGR60:E, E51, AR MODEL) – 5 CN951 1 CN951 VH-3P JW960 JW972 A AC-H T951 N POWER TRANSFORMER AC-H 3 JW974 JW976 P-GND LP963 JW978 JW977 PA BOARD (Page 40) R953 0.1 JW980 JW982 JW702 JW981 JW984 JW983 JW986 JW985 JW975 F964 T6.
PAGE 44
HCD-XGR6/XGR60 6-25. IC PIN FUNCTIONS r WAVEFORMS • IC101 DIGITAL SIGNAL PROCESSOR (CXD3017Q) (BD Board) – MAIN BOARD – 1 – BD BOARD – IC501 qa XC-OUT 1 Pin No. IC101 el FE 3.0Vp-p 0.15Vp-p 32KHz VOL/DIV : 1V AC TIME/DIV : 10µsec 2 IC501 qd X-OUT VOL/DIV : 0.1V AC TIME/DIV : 1msec 2 IC101 ra TE 2.0Vp-p 0.4Vp-p 16MHz VOL/DIV : 1V AC TIME/DIV : 50nsec 3 T331 4 TAPE REC only VOL/DIV : 0.2V AC TIME/DIV : 0.2msec 3 240Vp-p IC101 rd RFDC 0.
PAGE 45
HCD-XGR6/XGR60 Pin No. Pin Name Description I/O 53 CLTV I Control voltage input for master VCO 54 FILO O Filter output for master PLL 55 FILI I Filter input for master PLL 56 PCO O Chage-pump output for master PLL 57 AVDD3 — Powr supply (+3.3V) 58 VSS — Ground 59 VDD — Power supply (+3.3V) 60 DOUT O CD data output 61 LRCK O Not used (open) 62 PCMD O Not used (open) 63 BCK O Not used (open) 64 EMPH O Not used (open) 65 XVDD — Power supply (+3.
PAGE 46
HCD-XGR6/XGR60 • IC501 M30620MCN-A01FP SYSTEM CONTOL (MAIN Board) Pin No.
PAGE 47
HCD-XGR6/XGR60 Pin No. 54 Pin Name CAPM-H/L I/O O Discription Capstan motor high/low signal output 55 CAPM-CTRL O Capstan motor REV/FWD/STOP control signal output 56 A-PLAY I TCM-A play switch input 57 B-PLAY I TCM-B play switch input 58 TC-MUTE O TC line mute signal output 59 REC/PB/PASS O Not used (open) 60 NR ON/OFF O Not used (open) 61 REC-MUTE O REC mute signal output 62 VCC — Power supply (+3.
PAGE 48
HCD-XGR6/XGR60 • IC601 MB90M407APF-G-112-BND DISPLAY CONTROL (PANEL FL Board) Pin No.
PAGE 49
HCD-XGR6/XGR60 Pin No. 54 Description Pin Name SOFT TEST I/O O Not used (open) 55 LED SELB O LED group B select signal output 56 VOL A I Volume encoder signal A input 57 VOL B I Volume encoder signal B input 58 JOG A I AMS jog dial encoder signal A input 59 JOG B I AMS jog dial encoder signal B input 60 I2C-DATA O IIC serial data output 61 I2C-CLOCK O IIC clock signal output 62 AVCC — Power supply (+3.
PAGE 50
HCD-XGR6/XGR60 6-26.
PAGE 51
HCD-XGR6/XGR60 IC103 CXA2581N-T4 (BD BOARD) 30 DC_OFST RW/ROM APC LD 1 29 RFDCI PD 2 DVCC VC 28 RFDCO DVC VCC VC 27 VC EQ IN 3 AC SUM 4 AC SUM EQ 26 RFC 25 VFC 24 BST AC VCA 23 RFG EQ ON/OFF GND 5 VCC VOFST 22 VCC RW/ROM B C A 6 B 7 A C 8 D VCC 20 CE VC VC VOFST D 9 VC RW/ROM RW/ROM F 10 gm E 11 gm 21 CEI 19 TE_BAL DVCC RW/ROM 18 TE APC-OFF(Hi-Z) RW/ROM (H/L) SW 12 RW/ROM DVCC 13 AVC DVC VOFST DVC DVC 17 FEI DVCC VC DVC 14 16 FE DVC RFAC 15 IC321 µPC1330HA (M
PAGE 52
HCD-XGR6/XGR60 IC201 TA8409 (MOTOR BOARD) VREF BLOCK STANDBY BLOCK HEAT CUT OFF BLOCK 2 VCC 1 IN2 3 OUT2 5 GND 4 NC 6 VS 8 VREF 7 OUT1 IC602 BA3830F (PANEL FL BOARD) R02 1 REFERENCE CURRENT R01 2 REFERENCE CURRENT LINE NF 3 LINE IN 4 – + RESET BAND PASS FILTER DET REC NF 5 REC IN 6 RESET C BIAS C GND 7 8 9 – + 18 RESET 17 16 15 14 13 12 F01 F02 F03 F04 F05 F06 11 REC LEVEL 10 VCC 52 9 IN1
PAGE 53
HCD-XGR6/XGR60 SECTION 7 EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may have some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. • • Hardware (# mark) list and accessories are given in the last of this parts list.
PAGE 54
HCD-XGR6/XGR60 7-2. FRONT PANEL SECTION-1 59 56 54 57 55 not supplied 58 53 54 61 60 not supplied 54 62 52 54 54 54 54 63 #1 63 54 65 51 54 not supplied 64 Front panel section-2 Ref. No. Part No. Description 51 52 53 54 55 4-237-635-01 A-4727-633-A 1-683-448-11 4-951-620-01 4-237-648-01 KNOB (MIC) MIC/GUITAR BOARD, COMPLETE TC-A BOARD SCREW (2.
PAGE 55
HCD-XGR6/XGR60 7-3. FRONT PANEL SECTION-2 109 114 112 109 not supplied 110 113 FL601 111 108 104 109 109 110 109 106 114 115 not 109 supplied 109 105 #7 109 #7 123 103 109 109 118 107 116 102 117 119 109 109 101 supplied with S763 not supplied 109 120 121 122 109 Ref. No. Part No.
PAGE 56
HCD-XGR6/XGR60 not supplied 7-4. CHASSIS SECTION 154 #2 #5 #5 158 F951 #2 T951 F961 #1 156 F962 #1 F963 155 F964 153 159 #4 not supplied b b 160 #1 152 not supplied #1 #1 #1 #1 CDM37B-30BD60C not supplied 161 151 not supplied Ref. No. Part No.
PAGE 57
HCD-XGR6/XGR60 7-5. CD MECHANISM DECK SECTION (CDM-30BD60C) 501 501 509 505 #1 504 507 511 506 510 501 517 502 508 510 503 510 512 M201 502 518 520 518 519 520 516 519 BU-30BD60C 520 514 513 #1 520 522 521 521 524 515 #1 #1 #1 523 Ref. No. Part No.
PAGE 58
HCD-XGR6/XGR60 7-6. BASE UNIT SECTION (BU-30BD60C) 554 556 555 553 552 551 Ref. No. 551 552 553 554 555 58 Part No. Description 3-531-576-11 A-4728-678-A 4-233-832-01 4-233-831-01 1-757-710-11 RIVET BD BOARD, COMPLETE GEAR (LB) GEAR (LA) WIRE (FLAT TYPE) (16 CORE) Remarks Ref. No. 556 Part No.
PAGE 59
NOTE: Ref. No. Part No. Description • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX, -X mean standardized parts, so they may have some difference from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • CAPACITORS: uF: µF • RESISTORS All resistors are in ohms.
PAGE 60
HCD-XGR6/XGR60 BD CD-L CD-R D-SW FRONT INPUT Ref. No. R102 R103 R104 R105 Part No. 1-216-845-11 1-216-835-11 1-216-839-11 1-216-821-11 Description METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 15K 33K 1K 5% 5% 5% 5% Remarks 1/16W 1/16W 1/16W 1/16W R106 R107 R108 R109 R111 1-216-821-11 1-216-833-11 1-216-827-11 1-216-857-11 1-216-846-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 10K 3.
PAGE 61
HCD-XGR6/XGR60 FRONT INPUT Ref. No. C703 C704 C705 Part No. 1-126-960-11 1-164-159-21 1-162-282-31 Description ELECT CERAMIC CERAMIC 1uF 0.
PAGE 62
HCD-XGR6/XGR60 MAIN Ref. No. C331 C332 C333 C334 Part No. 1-137-150-11 1-126-961-11 1-130-485-00 1-130-481-00 Description MYLAR ELECT MYLAR MYLAR 0.01uF 2.2uF 0.015uF 0.0068uF 5% 20% 5% 5% Remarks 100V 50V 50V 50V C335 C336 C337 C338 C341 1-130-481-00 1-130-486-00 1-126-964-11 1-126-947-11 1-126-935-11 MYLAR MYLAR ELECT ELECT ELECT 0.0068uF 0.
PAGE 63
HCD-XGR6/XGR60 MAIN Ref. No. CN371 CN401 Part No. Description 1-784-776-11 CONNECTOR, FFC 15P 1-568-838-11 CONNECTOR, FFC 21P CN411 CN431 CN441 CN722 CN901 1-785-321-11 1-784-780-11 1-563-614-31 1-691-767-11 1-778-982-21 CN902 CN903 CN961 1-778-982-21 CONNECTOR, BOARD TO BOARD 13P 1-785-315-11 PIN, CONNECTOR (STRAIGHT) 3P 1-564-506-11 PLUG, CONNECTOR 3P Remarks PIN, CONNECTOR (STRAIGHT) 9P CONNECTOR, FFC 19P CONNECTOR, FLEXIBLE 11P PLUG (MICRO CONNECTOR) 5P CONNECTOR, BOARD TO BOARD 13P Ref. No.
PAGE 64
HCD-XGR6/XGR60 MAIN Ref. No. Q333 Q334 Q335 Part No.
PAGE 65
HCD-XGR6/XGR60 MAIN Ref. No. R341 R342 R343 R344 R345 Part No. 1-216-821-11 1-216-821-11 1-216-841-11 1-216-829-11 1-216-829-11 Description METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 47K 4.7K 4.7K 5% 5% 5% 5% 5% Remarks 1/16W 1/16W 1/16W 1/16W 1/16W R346 R347 R348 R349 R350 1-216-833-11 1-216-833-11 1-216-829-11 1-216-829-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 4.7K 4.
PAGE 66
HCD-XGR6/XGR60 MAIN MIC/GUITAR Ref. No. R604 Part No.
PAGE 67
HCD-XGR6/XGR60 MIC/GUITAR Ref. No. IC853 Part No. Description 8-759-505-55 IC NJM4558L Remarks < JACK > J801 J802 L201 Part No. 8-729-620-05 8-729-029-86 8-729-029-86 8-729-029-40 8-729-119-78 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR Description < COIL > 1-408-117-00 INDUCTOR PA Remarks 10uH < RESISTOR > 1-770-226-11 JACK (LARGE TYPE) (MIX MIC) 1-770-226-11 JACK (LARGE TYPE) (GUITAR) R205 R206 < TRANSISTOR > Q880 Q881 Q882 Q883 Q884 Ref. No.
PAGE 68
HCD-XGR6/XGR60 PA Ref. No. C854 C857 C858 C859 C861 Part No. 1-126-967-11 1-128-560-11 1-164-159-21 1-164-159-21 1-130-491-00 Description ELECT ELECT CERAMIC CERAMIC MYLAR 47uF 22uF 0.1uF 0.1uF 0.047uF 20% 20% C862 C863 C864 C891 1-130-491-00 1-126-961-11 1-126-964-11 1-127-811-11 MYLAR ELECT ELECT ELECT 0.047uF 2.2uF 10uF 3300uF 5% 20% 20% 20% C891 1-127-753-11 ELECT 3300uF 20% C892 1-127-814-11 ELECT 3300uF 20% C894 1-137-749-11 MYLAR 0.
PAGE 69
HCD-XGR6/XGR60 PA Ref. No. R810 Part No. Description 1-249-435-11 CARBON 33K 5% R810 1-249-437-11 CARBON 47K 5% R811 R812 R813 1-249-417-11 CARBON 1-249-431-11 CARBON 1-249-441-11 CARBON 1K 15K 100K 5% 5% 5% R814 R815 R816 1-249-421-11 CARBON 1-249-433-11 CARBON 1-249-429-11 CARBON 2.
PAGE 70
HCD-XGR6/XGR60 PANEL FL Ref. No. D611 D612 D613 Part No. 8-719-058-03 8-719-058-03 8-719-058-03 Description DIODE SEL5423E-TP15 (JAZZ) DIODE SEL5423E-TP15 (DANCE) DIODE SEL5423E-TP15 (GAME) Remarks Ref. No. R632 R633 R634 R635 Part No. 1-249-419-11 1-249-419-11 1-249-421-11 1-249-413-11 Description CARBON CARBON CARBON CARBON 1.5K 1.5K 2.
PAGE 71
HCD-XGR6/XGR60 PANEL FL Ref. No. S604 S605 Part No. Description 1-762-875-21 SWITCH, KEYBOARD (SAMBA) 1-762-875-21 SWITCH, KEYBOARD (MOVIE) Remarks Ref. No.
PAGE 72
HCD-XGR6/XGR60 PANEL VR SENSOR SUB TRANS TC-A Ref. No. S711 S713 S714 S715 Part No.
PAGE 73
HCD-XGR6/XGR60 TRANS Ref. No. C893 C961 C963 Part No. 1-137-749-11 1-162-306-11 1-162-306-11 Description MYLAR CERAMIC CERAMIC 0.1uF 0.01uF 0.01uF 30% 30% Remarks 100V 16V 16V Ref. No.
PAGE 74
HCD-XGR6/XGR60 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.0 Date 2002.