DSC-H5 SERVICE MANUAL LEVEL 2 US Model Canadian Model AEP Model UK Model E Model Australian Model Chinese Model Brazilian Model Hong Kong Model Korea Model Tourist Model Japanese Model Ver. 1.1 2006.
These specifications are extracted from User’s Guide/ Troubleshooting of DSC-H5 (2-673-176-11 (1)). SPECIFICATIONS Camera [Input and Output connectors] Dimensions [System] A/V OUT jack (Monaural) Minijack Video: 1 Vp-p, 75 Ω, unbalanced, sync negative Audio: 327 mV (at a 47 kΩ load) Output impedance 2.2 kΩ 113.2×83.0×94.0 mm (4 1/2 inches × 3 3/8 inches × 3 3/4 inches) (W/H/D, excluding protrusions) Mass Approx. 554 g (1 lb 3.
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. 2. 3. 4. 5. 6. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors.
TABLE OF CONTENTS 1. SERVICE NOTE 1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY ······ 1-1 1-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY ·················································· 1-2 1-3. PRECAUTION ON REPLACING THE SY-150 BOARD ··········································································· 1-3 1-4. VIDEO OUT DEFAULT DATA CHECK ······················· 1-3 1-5. INITIAL LANGUAGE DATA CHECK ·························· 1-3 2. DISASSEMBLY 2-1.
1. SERVICE NOTE 1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY Self-diagnosis display • C: ss: ss The contents which can be handled by customer, are displayed. • E: ss: ss The contents which can be handled by engineer, are displayed. Display Code C:32:ss C:13:ss E:61:ss E:62:ss E:91:ss E:92:ss Countermeasure Turn the power off and on again. Cause Trouble with hardware. Caution Display During Error SYSTEM ERROR Format the “Memory Stick” or internal “Memory Stick” or internal memory is memory. unformatted.
1-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) Note: 1 When replacing the SY-150 board, erase the data in internal memory of the board before replacement. Note: 2 When replacing the SY-150 board or the IC202 on the SY-150 board, execute formatting and initialize the internal memory after replacement.
1-3. PRECAUTION ON REPLACING THE SY-150 BOARD Ver. 1.1 2006. 06 • The Repair Board has already been adjusted. Re-initialization or EVR data copy from the set before repair is not required. • Perform “VIDEO OUT Default Data Check” and “Initial Language Data Check” mentioned below, and also the adjustment items necessary after SY Board replacement. 1-4.
2.
2. DISASSEMBLY 2. DISASSEMBLY NOTE FOR REPAIR Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. When remove a connector, don't pull at wire of connector. Be in danger of the snapping of a wire. When installing a connector, don't press down at wire of connector. Be in danger of the snapping of a wire. Cut and remove the part of gilt which comes off at the point.
2. DISASSEMBLY 2. DISASSEMBLY The following flow chart shows the disassembly procedure. 2-1. DISASSEMBLY 2 8 SW 1 47 7 1 SW1 7 4 5 6 2 3 4 3 1 1 Three screws (M1.7x4) 1 Two claws 4 Two claws, two dowels 2 Three screws (M1.7x4) 2 Flexible board (from the LCD unit) 5 Claw, two dowels 3 Cabinet (rear) section 3 Flexible board 6 Two tapping screws (M1.7x3.5) (from the light guide plate (3.
2. DISASSEMBLY 4 1 2 Refer to page 2-1 "DISCHARGING OF THE FLASHLIGHT POWER SUPPLY CAPACITOR, when discharging the capacitor. 2 1 3 3 1 6 2 7 4 HELP 04 8 5 9 3 HELP 05 HELP 07 HELP 06 1 A 2 HELP 08 1 Turn the flexible board. 2 Tapping screw (M1.7x5) 3 Lens section 1 Two tapping screws (M1.7x4) 1 Tapping screw (M1.
HELP Disassembling and assembling procedures that require attention are described here. HELP 01 When attaching the fuse replacement caution label to the SY-150 board, cover the harness of the loudspeaker with the fuse replacement caution label. Fuse replacement caution label Harnesses of the loudspeaker HELP 02 When installing the loudspeaker, route the harnesses of the loudspeaker as shown in the figure. Harnesses of the loudspeaker Loudspeaker (1.
HELP 05 HELP 04 When installing the ST section, route the Harness (HA-004) (Blue) ,Harness (HA-004)(White), and Harness (HA-004) (Red) as shown in the figure. When installing the ST section, route the Harness (HA-004) (Blue) ,Harness (HA-004)(White), and Harness (HA-004) (Red) as shown in the figure. ST section Route the harnesses with the ST cover closed.
HELP 07 Microphone holder Install the microphone tilted as shown in the figure below. Microphone cushion (B) Microphone holder Microphone Microphone cushion (B) Microphone Microphone cushion Microphone cushion HELP 08 When removing the lens ring, remove the screw and strap sheet metal (R) first. Slide the cap lever in the direction of arrow A while taking care that the cap lever is not caught on the notch of the lens ring. Remove the lens ring by turning it in the direction of arrow B.
3.
3. BLOCK DIAGRAMS ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. 3-1.
Ver. 1.1 2006. 06 3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. ST-003 FLEXIBLE FLAT CABLE SY-150 BOARD (2/2) ST-142 BOARD 1 | 3 1 | 3 ST-144 BOARD ST UNREG D102 (RECT) T101 XE H (3/8) 15 IC101 (2/2) R22 V23 AB22 STRB CHG STRB CHG 7 XSTRB FULL XSTRB FULL 6 STRB CHG CONT 5 STRB CHG CONT 7 10 6 9 5 6 HIGH VOLTAGE CHAGER STRB ON Q702 D1.
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. 3-3.
Ver. 1.1 2006. 06 3-4. POWER BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. SY-150 BOARD (2/2) L303 CAM 3.2V D 3.2V A 3.2V ST 5V CAM 2.9V 4 1 TG 3V FB308 DRVDD L304 (2/8) HDVDD L302 CP301 FE 3V TCVDD IC301 CD-617 BOARD CD-621 FLEXIBLE BOARD (2/8) IC001 S/H A/D CONV. TIMING GENERATOR RGVDD 3 BUFFER 3.3V REG CAM 15V FB302 FB301 22 22 IC002 18 18 CCD IMAGER CAM 15V CD L301 CAM -7.
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1.
4-2.
4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µ Link µF. 50 V or less are not indicated except for electrolytics and tantalums. • Chip resistors are 1/10 W unless otherwise noted. kΩ=1000 Ω, MΩ=1000 kΩ. • Caution when replacing chip parts. New parts must be attached after removal of chip.
4-2. SCHEMATIC DIAGRAMS 2 1 4 3 5 6 8 7 9 10 CD-617 BOARD IC002 4 3 2 1 V1 5 V2 32 6 VST 33 V2 7 H1A 34 V6 8 VL 35 9 V3A V1 V3A 14 13 12 11 10 V4 36 V3B 37 V3B V6 VST CL007 V5B 38 V7 39 V8 V4 V10 V5A 39P VHLD B R-6.0 P0 R-0.7 P0 R-0.7 P0 R-0.7 CL008 P0 R-0.7 P0 R-0.7 CL002 P0 R-0.7 CL003 P0 R-0.7 P0 R-0.7 P0 R-0.7 CL001 P0 R-7.2 P0 R-6.0 P0 R-5.4 P0 R-6.
2 1 3 4 5 6 7 8 9 10 SW-471 BOARD A LCD BACK LIGHT, FUNCTION SWITCH XX MARK:NO MOUNT S407 ZOOM T RB402 2200x4 33P S409 ZOOM W 1 CN401 C TO SW-478 FLEXIBLE BOARD (PAGE 4-12) D 33 REG_GND 32 REG_GND 31 NC 30 REG_GND 29 D_3.
2 1 3 4 5 6 CK-161 FLEXIBLE BOARD A LCD PANEL XX MARK:NO MOUNT 29P CN001 GND B TO SY-150 BOARD(7/8) CN707 C (PAGE 4-20 of LEVEL 3) D E 1 GND 2 VCC1 3 VCC2 4 4.
• Refer to page 4-3 for mark 0. 1 2 ST-142 BOARD FLASH DRIVE A 5 6 NO MARK:REC/PB MODE R :REC MODE P :PB MODE TO ST-003 FLEXIBLE FLAT CABLE (PAGE 4-13) ST_UNREG 1 2 ST_UNREG 3 STRB_ON 4 STRB_CHG_CONT 5 XSTRB_FULL 6 STRB_CHG 7 ST_5V 8 REG_GND 9 REG_GND 10 REG_GND 11 REG_GND 12 C101 22u 6.3V C102 22u 6.3V 9 10 3 5 L101 4.7uH ST_UNREG 8 7 T101 CONVERTER TRANSFORMER XX MARK:NO MOUNT CN101 12P B 4 3 2 C106 22u 6.
• Refer to page 4-3 for mark 0. 2 1 3 4 5 6 ST-144 BOARD 3 4 PL-045 BOARD FLASH A 2 1 A XX MARK:NO MOUNT Note: RY201 is not included in this COMPLETE of PL-045 board. PLUNGER XX MARK:NO MOUNT CN201 LND005 LND001 XE_H XE_+ 1 R001 1M B C002 0.
2 1 3 4 5 6 7 8 CONTROL SWITCH BLOCK A MODE/JOG DIAL, FUNCTION SW R111 2k R109 2k XX MARK:NO MOUNT R112 2k S107 S106 (MODE DIAL) FOCUS 2 4 B FINDER S102 S101 R104 2k BRK 1 2 3 4 1 6 R105 2k 3 R106 2k R101 4900 R107 2k 5 12 4 11 3 10 2 1 R110 2k R103 13 7 R108 10k C STEADY SHOT 2 1 2 1 R116 2k 4 3 4 3 R117 2k R118 2k 9 8 R115 2k R114 2k 2200 S103 R102 9300 SHUTTER S105 2 6 5 4 POWER 3 1 3 2 2 4 JOG DIAL S104 1 1 7 3 4 D S108
Ver. 1.1 2006. 06 2 1 3 4 5 Note: D001 (AF LED) is not supplied, but this is included in AF-105 flexible board complete. AF-105 FLEXIBLE BOARD AF LED,LENS COVER SW A D001 DOR5073 (AF LED) XX MARK:NO MOUNT S001 (LENS COVER OPEN) 10P 1 1 6 LND001 2 5 LND002 3 4 XLENS_COVER_SENSE 2 REG_GND 3 D_3.
2 1 4 3 5 SY-CD RELAY A XX MARK:NO MOUNT V10 VST V3B V1 V3A V6 V2 V8 VHLD V7 V5B V9 V5A TO SY-150 BOARD(2/8) CN301 D (PAGE 4-15 of LEVEL 3) 38 37 36 35 34 33 32 31 30 29 28 27 26 39 SY-SW RELAY XX MARK:NO MOUNT 33P 38 37 36 35 34 33 32 31 30 29 28 27 26 REG_GND CAM_15V_CD REG_GND REG_GND RG REG_GND H1A REG_GND H1B REG_GND H2B 16 15 14 13 12 11 10 9 8 16 15 14 13 12 11 10 9 8 REG_GND 7 7 TO SY-150 BOARD(7/8) CN702 V5A REG_GND 17 C V9 21 17 30 4 BL_H NC 29 5 NC NC 28 6
1 2 3 4 5 MS-030 FLEXIBLE FLAT CABLE A XX MARK:NO MOUNT B (PAGE 4-20 of LEVEL 3) C SY-ST RELAY 12P 12P REG_GND 1 1 REG_GND REG_GND 12 12 REG_GND MS_BS 2 2 MS_BS REG_GND 11 11 REG_GND MS_D1 3 3 MS_D1 REG_GND 10 10 REG_GND MS_D0 4 4 MS_D0 REG_GND 9 9 REG_GND MS_D2 5 5 MS_D2 ST_5V 8 8 ST_5V XMS_IN 6 6 XMS_IN STRB_CHG 7 7 STRB_CHG MS_D3 7 7 MS_D3 MS_SCLK 8 8 MS_SCLK TO MS-305 BOARD CN301 B (PAGE 4-9) TO SY-150 BOARD(7/8) CN701 (PAGE 4-20 o
4-3.
4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR WIRING BOARDS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) • : Uses unleaded solder. • : Pattern from the side which enables seeing. (The other layers’ patterns are not indicated) • Through hole is omitted. • There are a few cases that the part printed on diagram isn’t mounted in this model. • C: panel designation • Chip parts.
4-3. PRINTED WIRING BOARDS CD-617 (4 layers), SW-471 (4 layers) • : Uses unleaded solder.
ST-142 (2 layers), ST-144 (1 layer), MS-305 (4 layers) • : Uses unleaded solder.
Ver. 1.1 2006. 06 PL-045 (2 layers), AF-105 FLEXIBLE (1 layer), JK-306 FLEXIBLE (1 layer) • : Uses unleaded solder. PL-045 BOARD (SIDE B) PL-045 BOARD (SIDE A) 1 6 D202 CN201 D203 3 1 2 C201 >EP GW< S201 (FLASH POP UP) 2 1 1 2 PL045 RY201 (PLUNGER) 1-869-217- 11 1-869-217- 11 Note: RY201 is not included in this COMPLETE of PL-045 board.
CD-621 FLEXIBLE (2 layers), SW-478 FLEXIBLE (1 layer), CK-161 FLEXIBLE (2 layer) • : Uses unleaded solder.
4-3. PRINTED WIRING BOARDS no mark : side A * mark : side B 4-4.
NOTE 5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST NOTE: • -XX, -X mean standardized parts, so they may have some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied.
5. REPAIR PARTS LIST 5-1. EXPLODED VIEWS 5-1-1. OVERALL SECTION ns : not supplied 3 2 SW 1 47 3 4 8 1 ns LCD section (See page 5-4) 5 3 3 7 6 Ref. No. Part No. Description 1 2 2 3 3 2-673-346-01 2-673-327-11 2-673-327-21 2-630-005-31 2-655-582-11 PLATE, ORNAMENTAL CABINET (UPPER) (SILVER) CABINET (UPPER) (BLACK) SCREW (M2), NEW TRUSTER, P2 (BLACK) SCREW 0+P2 M2 NEWTRU-STAR (SILVER) 4 4 X-2108-909-1 CABINET (REAR) ASSY (420) (SILVER) X-2109-111-1 CABINET (REAR) ASSY (420D) (BLACK) Ref. No.
5. REPAIR PARTS LIST 5-1-2. LCD SECTION Cabinet (front) section (See page 5-7) 55 51 56 52 0 -15 SY 52 53 Lens section (See page 5-6) 58 60 Main section (See page 5-5) 54 57 LED9001 59 Ref. No. Part No. Description Ref. No.
5. REPAIR PARTS LIST 5-1-3. MAIN SECTION ns : not supplied 111 LCD9002 113 112 BT9001 102 MS -30 114 5 110 A 106 BT001 ns A 109 115 107 50 105 108 -1 SY 116 102 103 SP9001 104 102 101 ns : BT001 (Lithium battery) SY-150 board on the mount position. (See page 4-29) Ref. No. Part No. Description Ref. No. Part No.
5. REPAIR PARTS LIST 5-1-4. LENS SECTION ns : not supplied 161 154 158 157 151 153 155 17 -6 CD 156 IC002 152 159 160 ns ns Ref. No. Part No. Description 151 * 152 153 * 154 155 A-1177-128-A 2-672-563-01 2-592-693-01 2-672-565-01 1-788-338-11 SERVICE, OPTICS UNIT (B191A) (SERVICE) SHEET (LNS), RADIATION PLATE (T), LIGHT INTERCEPTION SHEET (TB), RADIATION OPTICAL FILTER BLOCK 156 * 157 2-592-605-01 RUBBER (TM), SEAL 2-672-562-01 SHEET (CD), RADIATION Ref. No.
5. REPAIR PARTS LIST 5-1-5. CABINET (FRONT) SECTION ns : not supplied ST section (See page 5-8) 208 209 212 207 210 211 219 213 202 206 214 205 MIC9001 202 215 216 ns 203 202 218 202 217 204 202 202 201 Ref. No. Part No. Description Ref. No. Part No.
5. REPAIR PARTS LIST 5-1-6. ST SECTION ns : not supplied 257 255 258 254 256 264 C105 251 Blue Red RY201 263 261 White 260 262 259 253 252 251 PRECAUTION DURING SOLENOID PLUNGER INSTALLATION 7 6 5 4 3 2 1 1 Close the ST cover. 3 Two claws 5 PL-045 board 2 Plunger solenoid 4 Solenoid retainer 6 Apply the soldering in two points. 7 Tapping screw (M1.7x4) Ref. No. Part No. Description Ref. No. Part No.
5. REPAIR PARTS LIST Checking supplied accessories. Make sure that the following accessories are supplied with your camcorder.
Ver. 1.1 2006. 06 AF-105 CD-617 CK-161 JK-306 MS-305 PL-045 5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. A-1176-913-A AF-105 FLEXIBLE BOARD, COMPLETE ****************************** (D001 (AF LED) is not supplied, but this is included in AF-105 flexible board complete.) Not supplied < CONNECTOR > CN001 DIODE DOR5073 (AF LED) (D001 (AF LED) is not supplied, but this is included in AF-105 flexible board complete.
PL-045 Ref. No. Part No. Description ST-142 Ref. No. ST-144 Part No. < SWITCH > A-1176-922-A SW-471 BOARD, COMPLETE *********************** < CAPACITOR > C106 < CONNECTOR > CERAMIC CHIP 22uF 20% 6.3V CERAMIC CHIP 22uF 20% 6.3V CERAMIC CHIP 1uF 10% 10V CAP, ELECT 320uF 330V (C105 is not included in this COMPLETE of ST-142 board.) 1-100-611-91 CERAMIC CHIP 22uF 20% * CN401 * CN402 1-815-333-51 CONNECTOR, FPC (ZIF) 33P 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P < DIODE > D401 D402 D403 6.
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)] Toolbar Printing a text Reversing the screens displayed once 1. Click the Print button . 2. Specify a printer, print range, number of copies, and other options, and then click [OK]. • To reverse the previous screens (operation) one by one, click . the • To advance the reversed screens (operation) one by one, click the .
Reverse 985211732.pdf Revision History Ver. Date 1.0 2006.04 Official Release 1.1 2006.06 Correction-1 DSC-H5_L2 History Contents — • Correction of service note • Correction of block diagrams • Correction of schematic diagrams • Correction of printed wiring boards • Correction of electrical parts list S.M. correction: Page 1-3E, 3-1, 3-2, 3-4E, 4-11, 4-27, 5-10 S.M. Rev.
