3-867-759-11 (2) DKC-FP3 Digital Still Camera Operating Instructions Before operating the unit, please read this manual thoroughly, and retain it for future reference. Owner’s Record The model and serial numbers are located on the bottom. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. DKC-FP3 Serial No.
WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. For the customers in the U.S.A.
Contents Battery Safety Precautions ...... 5 Operation Precautions .............. 6 Viewing Checking the Picture Content ......................... 39 To Maintain the Efficiency of the Camera ....................................... 7 Viewing Pictures on a Television ................... 44 Please Read This ....................... 8 Using the PC Card/Parallel Port Adaptor ....... 45 Checking the Supplied Accessories ............................. 10 Features ...................................
Playback Rotating the Picture ........................................ 87 Viewing an Enlarged Picture .......................... 88 Checking the Histogram of a Picture ............. 90 Erasing Erasing All Pictures ........................................ 91 Erasing Selected Pictures ............................... 92 Erasing Pictures during Playback ................... 94 Making it Impossible to Erase Important Pictures (Protect) ............................................
Battery Safety Precautions Follow the safety advice below to avoid leakage, internal heating, fires, explosions or accidental ingestion of batteries. Introduction DANGER (This applies only to battery packs) • Only charge the battery with the supplied charger. • Do not put the battery into fire. Do not short it out or dissassemble it. Do not heat in a microwave or conventional oven. If you carry or store the battery with metal objects such as coins or hairpins, shorts may occur.
Operation Precautions Places you should not leave your camera Introduction Do not operate or store your camera in places such as those listed below. Doing so may lead to the breakdown of your camera. • Unusually hot places If left in very hot places such as under the sun or in a car with the windows closed in summer, warping to the body or breakdown may occur. • In direct sunlight or near heating equipment Warping or breakdown may occur.
To Maintain the Efficiency of the Camera Operating and Storage Places Introduction To avoid possible breakdown, do not use or store the camera in the following places: • Extremely hot or cold places (The operating temperature is 0°C to +40°C (32°F to 104°F)) • In direct sunlight for long periods or near heating equipment • Humid or dusty places • Where it is exposed to rain • Places subject to strong vibrations • Near sources of strong magnetism • Near sources of powerful electromagnetic radiation, such a
Please Read This Test Shooting Before shooting, take a few test shots to make sure pictures are being taken normally. Introduction No Compensation for Picture Content If a picture is not recorded due to a problem with the digital still camera, the recording content cannot be compensated. Copyright Laws Pictures that you take with your digital still camera other than for personal enjoyment cannot be used without permission from the copyright owner in accordance with copyright laws.
Camera Playback Data Introduction • Picture data recorded by the camera may be played back on the camera • Picture data that has been edited on a personal computer or processed may not be played back by the camera even if it is recorded by the camera. Data Recorded on the PC Card Picture data is recorded in the following formats: IMJP XXXX (folder name)/MVC XXXXX.jpg (file name) (When the mode menu quality settings are High, Middle, and Low.) IMTIXXXX (folder name)/MVCXXXXX.
Checking the Supplied Accessories Before using the camera, make sure you have the following supplied accessories.
Memory Stick/PC Card Adaptor (1) Introduction “Memory Stick” (1) 11 GB
Features 1/2 Inch 1,500,000 Pixel CCD Introduction The digital still camera comes equipped with an all-pixel reading 1/2 inch CCD with 1,500,000 effective picture dots. The unit also uses a primary color filter and 1344 × 1024 pixel high-resolution to reproduce the natural colors and resolution of photographs. 5× Wide Zoom Lens To make the most of the high-resolution CCD, the camera is equipped with a 5¥ wide zoom lens for focal distances of 28 mm to 140 mm (equivalent to 35 mm film cameras).
Loading to a Video Output Terminal Using the PC Card and “Memory Stick” The digital still camera uses the highly reliable PC card (PCMCIA ATA TYPE II) and long-lasting “Memory Stick” (for use when inserted in the Memory Stick/PC Card Adaptor) as the image recording medium. Introduction If the unit is connected to a television by the supplied video cable, pictures taken by the digital still camera can easily be played back on the television.
Locations and Functions of Parts Front Locations and Functions of Parts 1 2 6 5 3 WB 4 1 Flash The camera has a built-in Guide Number GN10 flash. To use the flash, press the flash pop-up key. The cover will open and the flash warms up. The flash is stored when you close the cover. 2 Flash Pop-up Key Press the flash pop-up key to open the flash cover. 3 5× Zoom Lens You can manually adjust the zoom lens (28 mm to 140 mm (5×) on a 35 mm film camera) by rotating the zoom ring.
Rear 2 3 4 5 6 AE-LOCK R-REVIEW •PC •OFF DISP INDEX/EZ.FOCUS LCD •CAM •PLAY MENU EXCUTE EXIT !§ !∞ !¢ !£!™!¡0 9 87 !¶ !• !ª 1 Viewfinder Lets you frame the picture. 2 Eyesight Adjustment Lever Adjusts the level of the viewfinder to suit the eyesight of the picture taker. Locations and Functions of Parts 1 3 Review Button Lets you view and play back pictures during the time set in the REVIEW TIME of the custom menu when pressed directly after taking a picture.
7 Access Lamp Lights in red when a card is accessed by the camera during picture taking or playback. Locations and Functions of Parts Caution When the access lamp is lit, do not eject the card or turn off the power source. The PC Card or “Memory Stick” may be damaged. Note The PC Card and the “Memory Stick” installed in the Memory Stick/PC Card Adaptor are both referred to here as CARD. 8 LCD Button Switches the LCD monitor on and off. 9 INDEX/EZ.
qh Power/Mode Dial Note LCD Monitor Display When the power/mode dial is turned to CAM, the LCD monitor remains off. If necessary, press the LCD button to turn the LCD monitor on. When the power/mode dial is turned to PLAY, the LCD monitor automatically turns on. qj Card Cover Lock Slide this lock to enable card insertion or ejection. qk Card Eject Button Locations and Functions of Parts Selects camera conditions when turned while the mode lock (green) is held down. • OFF Turns the power off.
Top O E SIZ A IS US 3 AE QUAL E IV WB DR AL QU SIZE US ER EV DRIVE W B Locations and Functions of Parts 1 2 ISO AE AE-LOCK R-REVIEW !∞ !¢ !£ !™ !¡ 098 7 6 5 4 1 Focus Ring Rotate left or right to adjust the focus. 2 Zoom Ring Rotate left or right to adjust the zoom ratio of the zoom lens. 3 Release Button Operates the shutter when shooting.
9 Mode Dial 0 Shift Button Pressing this button after moving the mode dial to the desired position sets the picture quality or picture size (in CAM mode) or changes the picture that is played back (in PLAY mode). qa Connector Cover When using the video output terminal, the i.LINK terminal, or the remote control terminal, open this cover to connect the video cable. qs Connector Cover Lock Slide this lock to open the connector cover.
Bottom Locations and Functions of Parts 3 2 1 Tripod Hoke Attach a tripod here. Standards are as listed below. ISO Standard l = 4.5mm +/- 0.2mm ASA Standard l = 0.197 inch 2 Battery Cover Open or close this cover to insert or take out the battery pack. 3 Battery Cover Lock Slide this lock to insert or take out the battery pack.
LCD Panel Focus mode Shutter speed EV compensation ISO Sensitivity Aperture Picture taking mode Battery indicator Picture size Picture number Flash mode Interval/self-timer/ single picture/continuous picture taking indicator Card indicator Picture quality WB (white balance) mode Note In CAM mode/PC mode, when the release button is pressed while pressing the shift button, the shutter speed indicator changes to the remaining shot number indicator and the aperture indicator changes to remaining sh
LCD Monitor Locations and Functions of Parts CAM Mode/PC Mode Flash indicator Mode*1 WB (white balance) mode AF focusing indicator CAM WB-auto No.10267 1344/High Picture number Picture size/quality Frame (AE frame)*2 Keyword Picture folder name/ file name PICTURE01 1234/12345 0 0.25EV 2000 F4.0 Battery indicator (/Remaining shooting time*3) Remaining shot number Aperture Shutter speed EV compensation *1 The illustration above shows the monitor in CAM mode.
Viewfinder 2000 5.6 WB [ ] Light metering Shutter speed White balance aperture*/ EV compensation Flash indicator * The EV compensation is displayed when EV Button is pressed.
Preparations Charging the Battery Pack Preparations Charge the battery pack NP-F550 (not supplied) using AC power adaptor/charger AC-VQ800 (supplied). Be sure to charge the battery pack before using it for the first time. Charge the battery pack when necessary, as indicated by the remaining shooting time on the LCD monitor or the battery indicator on the LCD panel. Battery Pack Charging Time When it is time to charge the battery, the battery indicator on the LCD panel flashes.
4 4 5(a) 5 Pushing the battery pack down (a), slide it all the way to the left (b). When charging starts, the battery marks in the display window light in succession and the charge lamp lights. When the battery is charged, all of the battery marks light (practical use charge). Further, if you continue charging until the charge lamp goes out and the battery mark shows FULL, you can use the battery for a little longer than normal (full charge).
2 2(a) Slide the battery cover lock in the direction of the v mark (a), and open the battery cover (b). 2(b) Preparations 3 3 4 Insert the battery v mark side first until it firmly locks in place. Close the battery cover. Removing the Battery 1 2 3 3 26 GB Make sure the camera power/mode dial is set to the OFF position. Slide the battery cover lock in the direction of the v mark and open the battery cover. Rotate the battery cover lock to the outside and remove the battery pack.
Setting the Time and Date The shooting time and date are recorded automatically with information from the camera’s internal clock. Set the clock to ensure the correct time and date are recorded. 1 While pressing the mode lock (green), turn the power/mode dial to CAM mode. •PC •OFF 3~ 9 •CAM •PLAY MENU EXCUTE EXIT 2 2 4~9 Press the MENU button. The LCD monitor turns on and the menu is displayed. 3 Preparations 1 Press the v(UP)/V(DOWN) buttons to select “Date & Time”.
6 Set the year using the v(UP)/V(DOWN) buttons and then press the EXECUTE button. The month can now be set. Preparations 7 8 Set the month, day, hour, minutes and seconds in the same way as explained in step 5. Select “Date Form” using the v(UP)/V(DOWN) buttons and then press the EXECUTE button. You can now select the date display format. 9 Select the date display format using the v(UP)/ V(DOWN) buttons and then press the EXECUTE button. You can choose from the following 3 date display formats.
Preparing the Card Inserting the “Memory Stick” in the Memory Stick/PC Card Adaptor 1 1 Making sure the side of the “Memory Stick” with the v mark is facing up, insert it into the Memory Stick/PC Card Adaptor until it is locked firmly in place. Preparations The picture is saved on the PC Card inserted in the camera (not supplied) or on the “Memory Stick”. Insert the “Memory Stick” in the Memory Stick/PC Card Adaptor and then insert the adaptor into the camera.
Inserting the Card 1 Slide the card cover bar lock downward (a) and open the card cover (b). Preparations 1(b) 1(a) 2 2 Insert the card in the camera. Caution Make sure to insert the card in the proper direction. Forcing the card may result in damage to the camera and/or the card. If you insert a card that has never been initialized, FORMAT ERROR flashes on the LCD monitor. Initialize the card. (Page 31) 3 3 30 GB Close the card cover.
To Remove the Card 1 Open the card cover. 2 Push the card eject button. 3 Pull out the card. Preparations 3 1 2 Initializing a Card Uninitialized PC cards cannot be used in the camera. Before use, cards must first be initialized using the camera. Caution If you initialize a card that has data recorded on it, all recorded data, including protected picture data, will be erased. 1 1 While pressing the mode lock (green), turn the power/mode dial to CAM mode.
3 Select “PC Card INIT” using the v(UP)/ V(DOWN) buttons and then press the EXECUTE button. Preparations CAMERA MENU Custom PC Card INIT User File Save New Folder ID Set File No. Mem WB Flash Date & Time LCD Set Display Set The message “Initialize OK?” appears. 4 Press the EXECUTE button. Initialization begins. When initialization is complete, the LCD monitor returns to the normal display (as shown in step 1). Caution Do not take out the card during initialization.
Taking a Picture Taking Pictures Taking pictures is easy with automatic focus. In this manual, taking pictures while looking through the viewfinder is explained, but you can take pictures while looking through either the viewfinder or the LCD monitor. 2 1 •PC Take off the lens cap. •OFF •CAM •PLAY EXCUTE While pressing down the mode lock (green), turn the power/mode dial to CAM mode. The indicators in the viewfinder turn on.
6 Center the subject on which you’d like to focus in the center of the finder. 2000 8,9 7 8 Adjust the zoom by rotating the zoom ring left or right. Press the release button halfway. EV The AF LOCK indicator in the viewfinder flashes. When the subject is focused, the indicator stays lit and a beep sounds. (This setting can be changed so that the beep does not sound.) AL QU SIZE US ER DRIVE B W Taking a Picture 7 5.6 ISO AE AE-LOCK R-REVIEW 2000 5.
10 •PC •OFF •CAM •PLAY MENU EXCUTE EXIT 10 Turning the power/mode dial to OFF turns the power off. Note Auto Focus This camera employs an auto focus mechanism. When auto focus is turned on, the camera automatically focuses on the picture subject. Auto focus is turned on by setting the focus mode switch to AF. Centering the LCD monitor or the center of the finder on the subject and pressing the release button halfway focuses the picture frame.
Locking the Focus When you focus the picture by pressing the release button halfway, the focus is set at that distance until you release the button. This is called Focus Lock. If you want to take a picture of a subject on the edge of the picture composition, engaging Focus Lock allows you to move the camera and then take the picture. 1 Center the subject in the viewfinder and press the release button halfway. 1~3 AL QU SIZE US ER EV DRIVE B W Taking a Picture The focus is fixed.
Setting the Focus Manually You can set the focus manually with this camera. There are situations in which it is better to set the focus manually than use the auto focus function. Set the auto focus mode switch to MF. IS O USER 1 AE SIZE QUAL IV E WB DR 2 1 Adjust the focus by turning the focus ring left or right. Notes • The focus ring can be rotated completely in either direction. • Set the focus after adjusting the zoom.
Situations in which it is better to focus manually • When the subject and its surroundings are both dark; • When the subject offers little contrast on the screen, such as with walls or the sky; • When the background is too bright or the contrast between the background and the subject is too great; • When the subject has a fine, repeating pattern such as stripes; • When the subject is behind a window that is dirty or wet; • When there is a wire fence in front of the subject; • When the subject is bright, emi
Viewing Checking the Picture Content Below are the different ways for playing back recorded pictires. • Viewing pictures in succession Pictures are played back one by one in sequence. • Viewing pictures in an automatic cycle Pictures are automatically played back in a cycle. • Viewing the picture index Pictures are displayed all at once. This is a convenient way to search for a specific picture. Viewing Pictures in Succession 2 1 While pressing the mode lock (green), turn the power/mode dial to PLAY.
3 3 •PC •OFF •CAM •PLAY Turn the power/mode dial to OFF to turn off the power. Note MENU If the camera is on but not operated for about three minutes, power to the LCD monitor shuts off (Standby Mode). Also, if the camera is not operated for approximately another two minutes, the camera shuts off completely. In Standby Mode you can return to the playback condition by touching any button, dial or switch on the camera.
4 Select “Interval Time” using the v(UP)/ V(DOWN) buttons and then press EXECUTE. You can now set the number of seconds to display one picture. Auto Play Start Interval Time 2 sec Select the display interval time using the v(UP)/ V(DOWN) buttons and then press the EXECUTE button. Note Viewing 5 You can set the interval time between the range of 1 to 30 seconds (in 1 second units). However, depending on the playback quality and size, the set time might be overridden.
8 To end automatic playback, press the release button halfway. Automatic playback ends and the image appearing when you pressed the release button is displayed. 8 AL QU SIZE US ER EV ISO AE 9 DRIVE W B AE-LOCK R-REVIEW Turn the power/mode dial to OFF to turn the camera off. Note When the camera is set to automatic playback, the Auto Power Off function does not work. Viewing Viewing the Picture Index 1 2 1 The access lamp lights and the camera reads the last recorded picture.
3 Rotate the shift dial to select a picture. The color of the picture you have chosen changes and information about that picture, such as date and exposure, is displayed. O IS USER Note In Index Mode, when you rotate the shift dial while holding down the shift button, you can jump ten frames to choose a picture. When you rotate the shift dial while holding down the shift button and the release button simultaneously, you can jump 50 frames to choose a picture.
Viewing Pictures on a Television You can view pictures taken with the digital still camera on a television when it is connected to the TV’s video terminal. This is convenient for adjusting the focus and viewing pictures in succession. 1 2 REM OTE Use the video cable (supplied) to connect the camera video output terminal to the television video terminal. VIDE OUTO Note 1 SIZ E F A M IS O USER It is not possible to connect to a television that only has an antenna input terminal.
Using the PC Card/Parallel Port Adaptor When you connect the MSAC-PR1 PC card/parallel port adaptor on your computer and install the MSAC-PR1 device driver, the card is recognized as a drive. In this way, you can manage pictures saved on the card as computer files. The methods of connecting the PC card/parallel port adaptor to the computer and installing the PC card/parallel port adaptor driver are explained in this guide.
Installing the Driver 1 Insert the supplied CD-ROM into the CD-ROM drive. The “Sony MSAC-PR1 Setup” dialog box appears. 2 Click “Install Sony MSAC-PR1 Drivers”. The “Setup Language” dialog box appears. Viewing 3 Select a language and click [Next]. The “Welcome” dialog box appears.
4 Click [Next]. The “Software License Agreement” dialog box appears. 5 After reading and agreeing with the terms of the Software License Agreement, Click [Yes]. The “Choose Destination Location” dialog box appears. Viewing 6 Specify a destination folder for installation and click [Next]. The “Select Program Folder” dialog box appears.
7 Specify a program folder name and click [Next]. The “Start Copying Files” dialog box appears. Viewing 8 Confirm the displayed installation settings and click [Next]. Installation starts and the “Sony MSAC-PR1 Drive Identification” dialog box appears.
9 Confirm the drive name of the PC card/parallel port adaptor and click [OK]. The “Setup Complete” dialog box appears. Viewing 10 Click [Finish]. In step 9, if the “Yes, I want to read the README file now” box is checked, the README document is displayed. Installation is complete. Inserting the Card When you insert the card into the PC Card/Parallel port Adaptor, the drive that was specified as the drive name in step 8 of the “Install Driver” directions (page 49) is recognized.
Taking Out the Card 1 1 Make sure the power/access lamp is not flashing. Caution Do not take out the card when the power/ access lamp is flashing. Doing so may result in damage to your PC Card or “Memory Stick”. 2 2 Press the eject button and slowly pull out the card. Viewing Uninstalling the Driver If the MSAC-PR1 device driver is no longer necessary, you may remove it from your computer using the steps below.
Advanced Operations Settings Choosing the Exposure Mode Choose the exposure mode from the choices Program AE (Program), Aperture Priority AE (Aperture), Shutter Speed Priority AE (Shutter) or Manual Exposure (Manual). 1 1 While pressing the mode lock (green), turn the power/mode dial to CAM. •PC •OFF 3~ 6 •CAM •PLAY MENU EXCUTE 2 2 4~6 Press the LCD button to turn the LCD monitor ON. Note Settings can also be confirmed on the LCD panel.
Shutter (Shutter Speed Priority AE) When the shutter speed is fixed, the aperture is automatically changed according to the brightness of the subject to obtain the correct exposure. Manual (Manual Exposure) You can decide the exposure by setting the shutter speed and aperture manually. Note Exposure modes are indicated on the LCD panel as P (Program AE), A (Aperture priority AE), S (Shutter Speed priority AE), and M (Manual Exposure). 5 Release the shift button.
Choosing Picture Size Choose the picture size to be recorded during shooting from among the following: 1344 × 1024, 640 × 480, ×2D. Zoom. The larger the size, the fewer the number of pictures that can be recorded. 1 E IZ E DRIV WB AE 3~5 3 USER ISO USER 2 Press the LCD button to turn the LCD monitor ON. IS O Note SIZE SIZ E QUAL IV E WB DR •PC •OFF •CAM •PLAY While pressing the mode lock (green), turn the power/mode dial to CAM.
Because the picture frame narrows in this mode, check shots with the LCD monitor. You cannot check the true picture frame in the viewfinder. Note Picture size settings are indicated on the LCD panel as 1344 (1344 × 1024), 640 (640 × 480), and (×2 D. Zoom). 5 Release the shift button. When the picture size is set, exit the menu. The camera is ready to take pictures.
4 Rotate the shift dial while pressing the shift button. Choose a picture quality mode. CAM QUALITY Super High Middle Low Picture Size Super High Middle Low 1344 × 1024 Non compression Approx.1/4 Approx.1/8 Approx.1/16 640 × 480 ×2D. Zoom Non compression Approx.1/3 Approx.1/6 Approx.1/12 TIFF RGB picture JPEG Y-C compressed picture Select this to get the highest quality picture. High Select this when you want to give your picture quality priority over the number of pictures.
Choosing the Picture Taking Brightness (EV compensation) When a exposure mode other than manual exposure (Manual) is chosen, you can adjust the brightness to fit the shooting conditions. 1 1 While pressing the mode lock (green), turn the power/mode dial to CAM. AE-LOCK R-REVIEW DISP •OFF INDEX/EZ.FOCUS LCD •CAM •PLAY •PC •OFF 2 MENU EXCUTE •CAM •PLAY EXIT Press the LCD button to turn on the LCD monitor. Note 2 Settings can also be confirmed on the LCD panel.
Adjusting for Natural Color Tone (White Balance Adjustment) This camera comes equipped with the white balance function to give a more natural color tone to your pictures in a variety of shooting conditions. Choose a white balance mode from Auto White Balance (Auto), White Balance Hold (Hold), Outdoor (Outdoor), and Indoor (Indoor). With White Balance Hold you can adjust the most appropriate white balance for the shooting condition.
Auto (Auto White Balance) This is the default. White balance is automatically adjusted to give a natural color tone according to the amount of light when shooting. Hold (White Balance Hold) Choose this when you want better color reproduction or you are shooting a monochrome subject and background. Press the WB button to adjust the white balance. For further information refer to the Adjusting the White Balance Hold section below.
When the WB indicator disappears, white balance adjustment is complete. The camera is ready to take pictures. The white balance you have chosen is valid until you readjust it. Note When the WB indicator flashes, the white level was not successfully adjusted. Press any other operation button to leave this mode, then begin the white balance adjustment process again.
50 Sets sensitivity equal to ISO 50. Use this sensitivity when there is sufficient light, such as in the bright outdoors, for a finer image than with ISO 100. 100 Sets sensitivity equal to ISO 100. This is the standard ISO sensitivity. 400 Sets sensitivity equal to ISO 400. Use this sensitivity when you want to shoot a picture in a room without using a strobelight, or when there is not enough sunlight. The picture quality with this sensitivity is not as good as with ISO 100. 5 Release the shift button.
3 While pressing the [z] button (SPOT light meter switch button), turn the shift dial to choose the light meter reading method. CAM 3,4 LIGHT METERING AL QU SIZE US ER EV ISO AE DRIVE WB AE-LOCK R-REVIEW AVERAGE SPOT 3 AVERAGE (Center-weighted average light metering) Appropriate for average picture taking conditions. Takes the average light metering of the whole screen after you have placed the focal point in the center of the viewfinder.
Resetting the Content of the Setting Resetting the modes returns the following settings to those set forth by the factory. • mode dial settings • Miscellaneous Settings (page 73) R 1 SE U QUA L DRIVE W 3~5 3 SIZE 4 While pressing the mode lock (green), turn the power/mode dial to CAM mode. ISO AE B 2 Press the LCD button to turn on the LCD monitor. IS O USER Note SIZE SIZ E QUAL WB DR IV E •PC Settings can also be confirmed on the LCD panel.
Saving the Content of Settings You can save the content of the following settings in up to 3 user files. • mode dial settings • the content of Miscellaneous Settings (page 73) 1 1 While pressing the mode lock (green), turn the power/mode dial to CAM mode. •PC •OFF 3~ 6 •CAM •PLAY MENU EXCUTE 2 2 4~6 Press the MENU button. The LCD monitor turns on and the menu is displayed. EXIT 3 Choose “User File Save” using the v(UP)/ V(DOWN) buttons. 4 Press the EXECUTE button.
6 Press the EXECUTE button. The setting content is saved as a user file with the chosen file number. The date and time the file is saved is also displayed. 7 •PC •OFF Press the EXIT button. The LCD monitor display returns to the menu. •CAM •PLAY MENU 8 EXCUTE EXIT Press the EXIT button. After exiting the menu, the camera is ready to take pictures. 7,8 Reading the user file you have saved sets the same content in the user file.
4 While pressing the shift button, turn the shift dial to choose a user file number from No. 1 to No. 3. CAM USER FILE 5 ____ __________ No.0 No.1 No.2 No.3 (reset) 1999-07-04 1999-07-04 1999-07-04 Release the shift button. The content of the selected user file number is changed, and the camera is ready to take pictures. When you make a folder on a card, picures are thereafter saved in that folder. In this way you can manage pictures as you take them.
4 Press the EXECUTE button. The message “Add No.xxxx Folder OK?” appears. [xxxx] is the automatically attached folder name. 5 Press the EXECUTE button. The folder is created, and the camera is ready to take pictures. Pictures are thereafter saved in that folder. Note You can create about 510 folders on a card. Attaching Keywords (ID Numbers) to Pictures Advanced Operations Settings You can attach a keyword of up to 16 letters to a picture. The keyword is displayed when the picture is played back.
3 Select “ID Set” using the v(UP)/V(DOWN) buttons. CAMERA MENU Custom PC Card INIT User File Save New Folder ID Set File No. Mem WB Flash Date & Time LCD Set Display Set 4 Press the EXECUTE button. The keyword screen is displayed. ID SET P No.99 MODE Off ID No. [0123456789012345] 5 Select “Mode” using the v(UP)/V(DOWN) buttons and press the EXECUTE button. You can now change the mode setting. 6 Select “Off”, “Hold” or “Inc” using the v(UP)/ V(DOWN) buttons and press the EXECUTE button.
Inc Choose “Inc” if you want the number of the picture to be automatically included at the end of keyword every time you take a picture. (ex.) The keyword is PICTURE01 1st picture 2nd picture : PICTURE01 : PICTURE02 9th picture 10th picture : PICTURE09 : PICTURE10 Note When the automatic counter reaches [99], the number returns to [00] the next time you take a picture. The LCD monitor display returns to the keyword screen. Advanced Operations Settings 68 GB 7 Choose “ID No.
9 •PC •OFF •CAM •PLAY If you finish inputting the keyword before reaching the 16-letter limit, move the cursor to END and press the EXECUTE button. MENU 10 EXCUTE EXIT Press the EXIT button. The display on the LCD monitor returns to the menu. 10,11 11 Press the EXIT button. The menu disappears, and the camera is ready to take pictures. Adding or Changing a Keyword to a Picture that has Already been Taken 1 While pressing the mode lock (green), turn the power/mode dial to PLAY.
5 Press the EXECUTE button. The keyword input screen is displayed. If a keyword has already been attached to the picture, that keyword is displayed. ID SET P No.99 ID No. [0123456789012345] END BS CLR SPC 0123456789!"#$%&' ABCDEFGHIJKLMNOPQRS TUVWXYZ*+,-./;:<=>? 100MIN abcdefghijklmnopqrs tuvwxyz@[¥]^_{ } 0001/00009 6 Choose the letter you’d like to enter using the v(UP)/V(DOWN) buttons. Press the EXECUTE button. Advanced Operations Settings The letter you have chosen is input.
Choosing a Method to Attach a File Name to a Picture When a picture is taken, a number from 00001-99999 is automatically attached as a file name to the picture. The following methods to attach a number are possible. • Attach serial numbers on an individual card. • Attach serial numbers consecutively, even if the card is changed. Specifying a File Number Before Shooting 1 1 While pressing the mode lock (green), turn the power/mode dial to CAM.
5 Select “Memory” using the v(UP)/V(DOWN) buttons and press the EXECUTE button. You can now change the “Memory” setting. 6 Select either “off” or “on” using the v(UP)/ V(DOWN) buttons and press the EXECUTE button. off Serial numbers are attached as file names on each card. When this method is selected, specifying a starting number is not possible. on Serial numbers are attached as file names and continue in consecutive order even if a new card is inserted.
9 •PC •OFF •CAM •PLAY Press the EXIT button. The display on the LCD monitor returns to the menu. MENU EXCUTE 10 EXIT 9,10 Press the EXIT button. The menu disappears, and the camera is ready to take pictures. Miscellaneous Settings 1 1 While pressing the mode lock (green), turn the power/mode dial to CAM. •PC •OFF 3~ 6 •CAM •PLAY MENU EXCUTE 2 2 4,5 Press the MENU button. The LCD monitor turns on and the menu is displayed. EXIT 3 Choose “Custom” using the v(UP)/V(DOWN) buttons.
4 Press the EXECUTE button. The CUSTOM menu is displayed. CUSTOM Power Save on Interval Rec Time 00:00:10 Review off Review Time 5 sec Self-Timer 10 sec Sharpness Soft/Normal/Hard Histogram Manual/Auto Frame Beep on 5 Choose the item you would like to set using the v(UP)/V(DOWN) buttons and press the EXECUTE button. You can set the item you selected.
Note You can display the last picture taken at any time by pressing the REVIEW button. Review Time When Review is on or when the REVIEW button is pressed, the picture and/or histogram display time can be set for an interval within the range of 1 to 10 seconds (in one-second units). Self-Timer Sets the interval from when you press the RELEASE button to the time the shutter clicks within a range of 1 to 30 seconds (in one-second units).
• “Type” This item determines the type of frame displayed on the monitor. Selecting “AE frame” selects the AE frame type. This frame shows the light metering area used for determining exposure. Note that metering is done in the same manner regardless of whether the AE frame is displayed. Advanced Operations Settings 76 GB Selecting the “Guide 90” frame changes frame display to guide lines that can be moved horizontally.
• “Top” The “Top” item is used for setting the position of the Guide 90 or Guide 0 guide line that is bisected by a crosshair. The guide line can be positioned anywhere between the points that are 1/10 of the monitor width from the sides (for the Guide 90 frame) or top and bottom (for the Guide 0 frame) of the monitor. • “Bottom” The “Bottom” item is used for setting the position of the Guide 90 or Guide 0 guide line without the crosshair.
Advanced Operations Taking a Picture Shooting with the Flash Use the flash when taking pictures in dark places, such as indoors. A flash is built-in in the unit. Depending on shooting conditions, choose a flash mode from among Auto, On, Off, and External. When shooting in the External mode, attach an external flash to the accessory shoe to take flash pictures. Flash Mode Usage Guide Shooting Condition Normal Auto The subject is lit from behind. You want to use a flash during daytime.
Note Concerning Use of the Built-in Flash When photos are taken using the built-in flash, occlusion of light from the flash can occur under the following circumstances, resulting in a shadow at the bottom of the recorded image. If this occurs, change the zoom setting or use the optional external flash unit, as appropriate. 4 While pressing the shift button, turn the shift dial to select a flash mode. CAM FLASH Auto On Off External Auto • When shots are taken at the wideangle setting (f = 5.
If the flash mode is set to Auto or On, when the flash indicator flashes, the flash is warming up. When the flash lamp light becomes constant, the flash is ready for use. Flashing Continuously lit W B E A Note ISO DRIVE SIZE AL QU US ER When using the built-in flash, press the flash popup key to open it. When finished with the flash, push the top of the flash down to close.
4 Press the EXECUTE button. The WB FLASH menu is displayed. 5 Select “Flash Mode” using the v(UP)/V(DOWN) buttons and press the EXECUTE button. WB FLASH Flash Mode Interval Start Internal/External 10 sec(3~10) You can now set the flash mode. Choose “Internal” (built-in flash) or “External” (external flash) using the v(UP)/V(DOWN) buttons and press the EXECUTE button. Choose “Internal” to use the built-in flash or “External” to use the external flash and press the EXECUTE button.
9 Select “Start” using the v(UP)/V(DOWN) buttons and then press EXECUTE. “WB” is displayed in the viewfinder and white balance adjustment begins. After the flash lights about 10 times, the WB indicator goes off. The white balance adjustment is complete. The white balance value is valid until it is adjusted again. Note When the WB indicator flashes, the white balance is not successfully being adjusted.
4 While pressing the shift button, turn the shift dial to select “Cont1” or “Cont2.” CAM DRIVE 1Shot Cont1 Cont2 Self Timer Interval Rec Cont1 In this mode, when the shooting mode is set to a mode other than manual exposure, the exposure is automatically adjusted every time a picture is taken. Cont2 The continuous picture taking speed is faster in this mode than that in Cont1. Note These modes are indicated on the LCD panel as 1 (Cont1) and 2 (Cont2). 5 Release the shift button.
Taking a Picture at Regular Intervals (Interval Shooting) In this mode, after pressing the release button, pictures are continuously taken at regular intervals. How to set the shooting interval is described in the Miscellaneous Settings section (page 73). 4 DR IV E WB 1 QUAL AE O USER IS 3~5 3 While pressing the mode lock (green), turn the power/mode lock to CAM. SIZE 2 Press the LCD button to turn the LCD monitor on.
Taking a Picture with the Self-Timer In this mode, after pressing the release button, the shutter automatically clicks after a set period of time. How to set the time between the pressing of the release button and the shutter release is described in the Miscellaneous Settings section (page 73). IV E 1 While pressing the mode lock (green), turn the power/mode dial to CAM. DR WB 4 QUAL AE USER IS O 3~5 3 SIZE 2 Press the LCD button to turn the LCD monitor on.
Checking Pictures Directly After Shooting (Review Funcion and Histogram) When the REVIEW button is pressed directly after taking a picture, the picture is displayed on the LCD monitor in this mode. When you turn the review function on in Miscellaneous Settings, pictures are displayed automatically, without having to press the REVIEW button. Also, when histogram is set to “Auto” in “Miscellaneous Settings”, the histogram for a picture is displayed when that picture is displayed.
Advanced Operations Playback Rotating the Picture You can rotate the picture 90° clockwise or counter-clockwise, or 180° during playback. 1 1 •PC •OFF 3~ 6 While pressing the mode lock (green), turn the power/mode dial to PLAY. The LCD monitor turns on. •CAM •PLAY MENU EXCUTE EXIT 2 4~6 2 3 Push the MENU button. The menu is displayed on the LCD monitor. Choose “Rotate” using the v(UP)/V(DOWN) buttons. PLAY MENU 4 5 Press the EXECUTE button. The ROTATE menu is displayed.
The picture is displayed at the angle of rotation chosen. 6 7 •PC •OFF •CAM •PLAY Rotate the picture as described in step 5 as often as necessary. Press the EXIT button. The LCD monitor returns to the menu display. Note, however, that infomation of rotation changes made to protected pictures is not saved. MENU EXCUTE EXIT 7,8 8 Press the EXIT button. The menu disappears. Advanced Operations Playback Viewing an Enlarged Picture You can view an enlarged detail of a picture during playback.
4 Press the EXECUTE button. The area of the picture to be enlarged is framed with a green line. No.1 0001/00001 5 Select the area to be enlarged using the v(UP)/ V(DOWN) buttons. The frame moves left when the v(UP) button is pressed. No.1 0001/00001 6 Press the EXECUTE button. The selected area is enlarged and displayed, and the position of the enlarged area is displayed in the upper left corner. No.1 Advanced Operations Playback The frame moves right when the V(DOWN) button is pushed.
Note While viewing this screen, you can change the area to be enlarged by pressing the v(UP)/ V(DOWN) buttons. 7 •PC •OFF •CAM •PLAY Press the EXIT button. The enlargement indicator is cancelled. MENU 8 EXCUTE Press the EXIT button. The menu returns to the LCD monitor display. EXIT 7~9 9 Press the EXIT button. The menu disappears.
Advanced Operations Erasing Erasing All Pictures You can erase all saved pictures that are no longer needed from the card. However, you cannot erase pictures that have been protected. 1 1 While pressing the mode lock (green), turn the power/mode dial to PLAY. •PC The LCD monitor turns on. •OFF 3~ 5 •CAM •PLAY MENU EXCUTE EXIT 2 4~6 2 Press the MENU button. The menu appears on the LCD monitor. 3 Select “Delete” using the v(UP)/V(DOWN) buttons. 4 Press the EXECUTE button.
6 Press the EXECUTE buttons. Picture erasing begins. When deletion is finished, the LCD monitor display returns to the state shown in step 1. Caution Do not remove the card during picture deletion. Damage to the “Memory Stick” or PC Card may occur. Erasing Selected Pictures You can erase selected saved pictures, with the exception of protected pictures, from the card. 1 1 •PC Advanced Operations Erasing The LCD monitor turns on.
5 Choose “Select” using the v(UP)/V(DOWN) buttons and then press the EXECUTE button. The screen from which to choose pictures for deletion appears. 6 6 Turn the shift dial to the picture you would like to erase and press the EXECUTE button. The chosen picture is marked. AE-LOCK R-REVIEW •PC •OFF DISP INDEX/EZ.FOCUS LCD •CAM •PLAY MENU EXCUTE EXIT Note Protected pictures cannot be chosen. 7 8 Repeat step 6 to choose other pictures to be erased.
9 Press the EXECUTE button. Picture erasing begins. When deletion is finished, the LCD monitor returns to the state shown in step 5. Caution Do not remove the card during picture deletion. Damage to the “Memory Stick” or PC Card may occur. 10 •PC •OFF •CAM •PLAY Press the EXIT button. The LCD monitor display returns to the state shown in step 4. MENU 11 EXCUTE Advanced Operations Erasing EXIT Press the EXIT button. The LCD monitor display returns to the menu. 10~12 12 Press the EXIT button.
3 Select “Delete” using the v(UP)/V(DOWN) buttons. PLAY MENU Rotate D.Zoom Auto Play Protect Delete PC Card INIT ID Set LCD Set Display Set 4 Press the EXECUTE button. The Delete menu is displayed. 5 Select “1 Shot” using the v(UP)/V(DOWN) buttons and then press the EXECUTE button. 1 Shot Select All The message “Do you delete this image?” appears. Note To cancel erase, press the EXIT button. 6 Press the EXECUTE button. Advanced Operations Erasing Delete Picture erasing begins.
7 •PC •OFF •CAM •PLAY Press the EXIT button. The LCD monitor display returns to the menu. MENU 8 EXCUTE Press the EXIT button. The menu disappears. EXIT 7,8 Making it Impossible to Erase Important Pictures (Protect) You can save pictures from being accidentally erased. This is called “protecting” the picture. You can protect pictures when they are shown on the LCD monitor during playback.
4 Press the EXECUTE button. The PROTECT menu is displayed. PROTECT 1 Shot on/off All on All off 5 Choose “1 Shot on/off” using the v(UP)/ V(DOWN) buttons and then press the EXECUTE button. The chosen picture is protected, indicated by a P on the LCD monitor. No.3 PROTECT 1 Shot on/off All on All off 0001/00008 Notes • When you perform the same operation on a picture that has already been protected, the protect function is removed.
Advanced Operations Miscellaneous Setting the LCD Monitor Display You can set whether or not information related to picture taking or playback is displayed on the LCD monitor. 1 1 While pressing the mode lock (green), turn the power/mode dial to CAM. •PC •OFF 3~ 6 Note •CAM •PLAY MENU EXCUTE EXIT In this section, setting the LCD monitor display is explained while the power/mode dial is set to CAM, but the same operation can be done while the power/mode dial is set to PLAY.
5 Select the item you want to set using the v(UP)/ V(DOWN) buttons and press the EXECUTE button. The selected item is ready to change. DISPLAY SET Size/Qlty/Rotate Folder/File Name ID No. Date/Time Remaining Shot Tv/Av/Evcomp Frame 6 on on on on on on on Select “on” or “off” using the v(UP)/V(DOWN) buttons and then press the EXECUTE button. Items which can be set are listed below: Folder/File Name ID No.
Adjusting Picture Display on the LCD Monitor Adjusts picture display items such as contrast, brightness, and display range on the LCD monitor. 1 1 While pressing the mode lock (green), turn the power/mode dial to PLAY. •PC The LCD monitor turns on. •OFF 3~ 6 •CAM •PLAY MENU EXCUTE Note In this section, adjusting the picture display is explained while the power/mode dial is set to PLAY, but the same operation can be done while the power/mode dial is set to CAM.
6 Choose a value using the v(UP)/V(DOWN) buttons and press the EXECUTE button. The items you can set are listed below: Contrast, Bright, Color or Picture Contrast, brightness, color density or picture sharpness can be set within a -10 to +10 range (in units of 1). Disp Area (Display area) When NORMAL is chosen, the picture is displayed after being resized to fit the frame 100%. When OVER is chosen, the picture is displayed without being resized.
Operation by Remote Control Using the supplied remote control RM-S7D, you can perform the same operations as with the release button and shift dial operations on the camera itself. The remote control is convenient when you want to take pictures without holding the camera or for playing back pictures on a television. Further, when operating from a position where the camera cannot receive the remote control signal, connect the camera and remote control with the remote control cable (supplied).
2 3 Insert a lithium button battery CR2025 into the battery case, making sure the + (plus) side is visible. Return the battery cover to its original position. 1 REM OTE VIDE OUTO Using the remote control cable (supplied), connect the remote control terminal on the camera to the corresponding terminal on the remote control.
Using a Wall Socket To take or play pictures without using the battery pack, plug the camera into a wall socket using the battery adaptor/charger AC-VQ800 (supplied) and DC power cable DK-415 (supplied with the ACVQ800). 1 2 3 2 1 Advanced Operations Miscellaneous 104 GB 2 3 4 4 Slide the AC adaptor/charger’s mode switch to video/camera. Connect the DC and AC power cables to the AC adaptor/charger. Make sure the power/mode dial on the camera is set to OFF.
7 Insert the DC power cable connector v mark side first into the battery case until it locks firmly into place. 7 8 Put the cable into the battery cover groove and close the battery cover. Connecting to the PC If the camera and the PC are connected using the PC interface cable (supplied), pictures stored on the PC card can be read by the PC and you can operate the camera from the PC.
•PC 2 •OFF •CAM •PLAY MENU EXCUTE EXIT Advanced Operations Miscellaneous 106 GB 2 While pressing the mode lock (green), turn the power/mode dial to the PC position. Start the TWAIN driver software (supplied). Note The camera cannot be operated from the PC if the camera is being operated or the menu appears on the LCD monitor. • In PC mode, the LCD monitor turns OFF automatically after 15 seconds, even if it is set to ON. • The menu displayed in PC mode is the same as that displayed in CAM mode.
Menu Summary There are three menus in the camera: Shooting Menu, Camera Menu, and Playback Menu. CAM AE MODE Program Aperture Shutter Manual CAM FLASH Auto On Off External CAM Mode Menu The menu for setting shooting conditions. To call up this menu, turn the power/mode dial to CAM or PC*, turn the mode dial and press the shift button. PICTURE SIZE 1344x1024 640 x 480 X2 D.Zoom CAM QUALITY CAM WB-auto +0.50EV 300 0 F3.
CUSTOM Power Save on Interval Rec Time 00:00:10 Review off Review Time 5 sec Self-Timer 10 sec Sharpness Soft/Normal/Hard Histogram Manual/Auto Frame Beep on Card Initialization Initializes the card inserted in the camera. → Page 31 PC CARD INIT Initialize OK? Camera Menu The menu for setting the shooting conditions and camera functions. To call up the camera menu, turn the power/mode dial to the CAM or PC* position and press the MENU button.
LCD Monitor Picture Display Fine Tuning Adjusts picture display items such as contrast, brightness, and display range on the LCD monitor. → Page 100 LCD SET Contrast Bright Color Picture Disp Area 0 0 0 0 Normal DISPLAY SET Size/Qlty/Rotate Folder/File Name ID No. Date/Time Remaining Shot Tv/Av/Evcomp Frame on on on on on on on LCD Monitor Display Setting Sets whether or not information necessary for shooting or playing back a picture such as picture size and Frame is displayed on the LCD monitor.
Picture Rotation Rotates a picture 90° clockwise or counterclockwise, or 180° during playback. → Page 87 ROTATE 90 cw 90 ccw 180 No.1 Picture Enlargement Enlarges and displays a detail of a picture during playback. → Page 88 Playback Menu The menu for setting different picture and playback options. To call up the menu, turn the power/mode dial to the PLAY position and press the MENU button.
DISPLAY SET Size/Qlty/Rotate Folder/File Name ID No. Date/Time Remaining Shot Tv/Av/Evcomp Frame on on on on on on on LCD Monitor Display Setting Sets whether or not necessary information for picture taking or playback, such as picture size or Frame, is displayed on the LCD monitor.
Maintenance Maintenance of the Camera Surface If the camera surface gets dirty, lighty wipe with a dry cloth. If the camera is very dirty, wipe with a cloth moistened with a small amount of neutral detergent and wipe dry. • When using a chemical cleaning cloth, follow the manufacturer’s instructions. • Do not use volitile liquids such as alcohol, thinner or benzine on the camera surface. They will remove paint from the surface finish.
Troubleshooting Before bringing in your camera for servicing, check the following table as a guide to troubleshoot the problem. If the problem cannot be corrected, contact the place of purchase or your Sony dealer. If messages you are unfamiliar with appear in the viewfinder, or on the LCD panel or LCD monitor, refer to “Warning Indicators” on page 116. Symptom Camera is inoperable. Power cuts out. Cause Charge the battery pack. (page 24) AC power adaptor/charger is not firmly connected.
Symptom Auto focus does not work. Picture is dark. Cause Corrective Action AF switch is set to MF (manual Set the AF switch to AF focus) (auto focus). Pictures are being taken in conditions where auto focus does not work. Manually set the focus. (page 37) Subject is backlit. There is insufficient light. Correct the brightness. (page 56) When shooting a bright subject, These lines are called “smears.” The camera is not vertical lines appear on the malfunctioning. picture.
Symptom Picture is not recorded when you press the release button. Cause Corrective Action A card is not inserted in the camera. Insert a card in the camera. (page 30) There are no more remaining shots. Insert a new card. Change the picture quality or erase unnecessary pictures. Check the remaining shot number and try again. (pages 54, 91) Files names for pictures recorded on the card have reached 99999. Vertical lines appear around This occurs when there is a lights or candle flames, etc.
Warning Indicators LCD Monitor The following warning indicators appear on the LCD monitor. Low Battery Charge Indicator When the battery voltage becomes low, the remaining battery time indicator on the LCD monitor changes to the indicator.* * When using the AC power adaptor/charger, this indicator does not appear. CARD FULL No Shot Available If you press the release button when the picture file on the card is full, the message CARD FULL is displayed in red for 4 seconds.
LCD Panel The following warning indicators appear on the LCD panel. Battery Indicator As the battery voltage becomes low, on the LCD panel. is indicated The battery indicator changes as follows: Battery Indicator Battery Charge Amount Standard (A fully charged battery is 100%) 100 to 80% 80 to 60% 60 to 40% 40 to 20% 20 to 10% * When using the AC power adaptor/charger, this indicator does not appear.
EV Indicator The letters EV appear whenever EV compensation mode is on. When EV compensation is turned to +/- 0.0, the indicator does not appear. Auto Focus Off Indicator When the AF switch is turned to MF (manual focus), the MF indicator appears.
Error Messages The following messages are displayed on the camera’s LCD monitor or LCD panel or in the viewfinder. Refer to list below for the meaning of the error message. Message on LCD Panel or Message on LCD Monitor in Viewfinder Meaning and Corrective Action NO CARD A card is not inserted. → Insert a card into the camera. (page 30) Full CARD FULL The maximum number of pictures has been recorded on the card. → Erase unnecessary pictures (page 91) or insert a new card.
Message on LCD Panel or Message on LCD Monitor in Viewfinder Miscellaneous 120 GB Meaning and Corrective Action Err12 NO ID INFO A keyword was attempted to be added to a picture that was not recorded by the camera. → Keywords can only be added to pictures recorded by the camera. (page 66) Err13 DATE & TIME NOT SET The lithium button battery used to maintain the internal clock has run out. → Contact your nearest Sony dealer or Sony Customer Service.
Specifications System Camera type Digital still camera Picture quality modes Super – TIFF (Non compression) High, Middle, Low – JPEG (compression) Recording medium PCMCIA ATA TYPE II card Sony “Memory Stick” (for use with Memory Stick/PC Card Adapter) Picture elements 1/2 inch single-plate, solid-state picture element (all elements read) Optical viewfinder Focusing screen with built-in double imaging, single ref type LCD monitor 2.
Internal flash External light sensor, self-adjusting system: adjusts to all shutter speeds Guide Number: GN10 Range: 1.0 to 2.5 meters approx. (ISO 100, without EV compensation) Flash modes: Auto/On/Off White balance Auto/One push hold/Indoor/Outdoor Video output terminal NTSC model: 1.0Vp-p 75Ω, unbalanced, sync negative PAL model: Miscellaneous 122 GB 1.
Accessories Viewfinder cap (fitted on the lens, 1) Lens cap (fitted on the lens, 1) Video cable (1) Wireless remote control (1) Remote control cable (5 meters, 1) AC adaptor/charger AC-VQ800 (DK-415 supplied with the AC-VQ800, 1) PC interface cable (1) “Memory Stick” (1) Memory Stick/PC Card Adaptor (1) TWAIN Driver Software CD-ROM (1) User’s manual (this manual, 1) Warranty (1) Design and specifications are subject to change without notice.
Index A AE-LOCK ............................................. Aperture ................................................. Aperture Priority AE .............................. Auto Focus ............................................. Auto Power Off Function ...................... Automatic Cycle Viewing ............... 39, I 36 51 51 35 73 40 13 13 39 31 84 59 B K Battery ............................................ 24, 25 Battery Cover Lock ............................... 26 Battery Indicator ............
R Reading Setting Content ........................ 64 Remote Control ................................... 102 Remote Control Cable .................. 19, 102 Resetting Settings Content .................... 62 Review Funcion and Histogram ............ 86 Review Function .................................... 73 Rotation ................................................. 87 S Saving User Files ................................... Self-Timer ....................................... 73, Sharpness ...................
Index 126 GB
Index 127 GB
For information regarding the DKC-FP3, please see our Internet home page at http://www.world.sony.
